ide: dead/stale code removal

index 9ac4e37..0c6155f 100644
@@ -869,10 +869,10 @@ static void do_pata_set_dmamode(struct ata_port *ap, struct ata_device *adev, in
 				(timings[pio][1] << 8);
 		}
 
-		if (ap->udma_mask) {
+		if (ap->udma_mask)
 			udma_enable &= ~(1 << devid);
-			pci_write_config_word(dev, master_port, master_data);
-		}
+
+		pci_write_config_word(dev, master_port, master_data);
 	}
 	/* Don't scribble on 0x48 if the controller does not support UDMA */
 	if (ap->udma_mask)

index 0df83cf..95ebdac 100644
@@ -90,48 +90,12 @@ static void cs5520_set_timings(struct ata_port *ap, struct ata_device *adev, int
 }
 
 /**
- *	cs5520_enable_dma	-	turn on DMA bits
- *
- *	Turn on the DMA bits for this disk. Needed because the BIOS probably
- *	has not done the work for us. Belongs in the core SATA code.
- */
-
-static void cs5520_enable_dma(struct ata_port *ap, struct ata_device *adev)
-{
-	/* Set the DMA enable/disable flag */
-	u8 reg = ioread8(ap->ioaddr.bmdma_addr + 0x02);
-	reg |= 1<<(adev->devno + 5);
-	iowrite8(reg, ap->ioaddr.bmdma_addr + 0x02);
-}
-
-/**
- *	cs5520_set_dmamode	-	program DMA timings
- *	@ap: ATA port
- *	@adev: ATA device
- *
- *	Program the DMA mode timings for the controller according to the pio
- *	clocking table. Note that this device sets the DMA timings to PIO
- *	mode values. This may seem bizarre but the 5520 architecture talks
- *	PIO mode to the disk and DMA mode to the controller so the underlying
- *	transfers are PIO timed.
- */
-
-static void cs5520_set_dmamode(struct ata_port *ap, struct ata_device *adev)
-{
-	static const int dma_xlate[3] = { XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 };
-	cs5520_set_timings(ap, adev, dma_xlate[adev->dma_mode]);
-	cs5520_enable_dma(ap, adev);
-}
-
-/**
  *	cs5520_set_piomode	-	program PIO timings
  *	@ap: ATA port
  *	@adev: ATA device
  *
  *	Program the PIO mode timings for the controller according to the pio
- *	clocking table. We know pio_mode will equal dma_mode because of the
- *	CS5520 architecture. At least once we turned DMA on and wrote a
- *	mode setter.
+ *	clocking table.
  */
 
 static void cs5520_set_piomode(struct ata_port *ap, struct ata_device *adev)

@@ -149,7 +113,6 @@ static struct ata_port_operations cs5520_port_ops = {
 	.qc_prep		= ata_sff_dumb_qc_prep,
 	.cable_detect		= ata_cable_40wire,
 	.set_piomode		= cs5520_set_piomode,
-	.set_dmamode		= cs5520_set_dmamode,
 };
 
 static int __devinit cs5520_init_one(struct pci_dev *pdev, const struct pci_device_id *id)

index 2a6412f..b2e71e6 100644
@@ -2,6 +2,7 @@
  *    pata_efar.c - EFAR PIIX clone controller driver
  *
  *	(C) 2005 Red Hat
+ *	(C) 2009 Bartlomiej Zolnierkiewicz
  *
  *    Some parts based on ata_piix.c by Jeff Garzik and others.
  *

@@ -118,12 +119,12 @@ static void efar_set_piomode (struct ata_port *ap, struct ata_device *adev)
 		int shift = 4 * ap->port_no;
 		u8 slave_data;
 
-		idetm_data &= 0xCC0F;
+		idetm_data &= 0xFF0F;
 		idetm_data |= (control << 4);
 
 		/* Slave timing in separate register */
 		pci_read_config_byte(dev, 0x44, &slave_data);
-		slave_data &= 0x0F << shift;
+		slave_data &= ap->port_no ? 0x0F : 0xF0;
 		slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << shift;
 		pci_write_config_byte(dev, 0x44, slave_data);
 	}

@@ -200,7 +201,7 @@ static void efar_set_dmamode (struct ata_port *ap, struct ata_device *adev)
 			master_data &= 0xFF4F;  /* Mask out IORDY|TIME1|DMAONLY */
 			master_data |= control << 4;
 			pci_read_config_byte(dev, 0x44, &slave_data);
-			slave_data &= (0x0F + 0xE1 * ap->port_no);
+			slave_data &= ap->port_no ? 0x0F : 0xF0;
 			/* Load the matching timing */
 			slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
 			pci_write_config_byte(dev, 0x44, slave_data);

@@ -251,7 +252,7 @@ static int efar_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 	static const struct ata_port_info info = {
 		.flags		= ATA_FLAG_SLAVE_POSS,
 		.pio_mask	= ATA_PIO4,
-		.mwdma_mask	= ATA_MWDMA2,
+		.mwdma_mask	= ATA_MWDMA12_ONLY,
 		.udma_mask 	= ATA_UDMA4,
 		.port_ops	= &efar_ops,
 	};

index d30da80..9a09a1b 100644
@@ -80,14 +80,13 @@ static struct hpt_clock hpt3x2n_clocks[] = {
 
 	{	XFER_MW_DMA_2,	0x2c829c62	},
 	{	XFER_MW_DMA_1,	0x2c829c66	},
-	{	XFER_MW_DMA_0,	0x2c829d2c	},
+	{	XFER_MW_DMA_0,	0x2c829d2e	},
 
 	{	XFER_PIO_4,	0x0c829c62	},
 	{	XFER_PIO_3,	0x0c829c84	},
 	{	XFER_PIO_2,	0x0c829ca6	},
 	{	XFER_PIO_1,	0x0d029d26	},
 	{	XFER_PIO_0,	0x0d029d5e	},
-	{	0,		0x0d029d5e	}
 };
 
 /**

index 7e31025..c86c716 100644
@@ -255,8 +255,17 @@ static int hpt3x3_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 #ifdef CONFIG_PM
 static int hpt3x3_reinit_one(struct pci_dev *dev)
 {
+	struct ata_host *host = dev_get_drvdata(&dev->dev);
+	int rc;
+
+	rc = ata_pci_device_do_resume(dev);
+	if (rc)
+		return rc;
+
 	hpt3x3_init_chipset(dev);
-	return ata_pci_device_resume(dev);
+
+	ata_host_resume(host);
+	return 0;
 }
 #endif
 

index f156da8..8f3325a 100644
@@ -22,7 +22,7 @@
 #define DRV_VERSION	"0.0.3"
 
 /**
- *	it8213_pre_reset	-	check for 40/80 pin
+ *	it8213_pre_reset	-	probe begin
  *	@link: link
  *	@deadline: deadline jiffies for the operation
  *

@@ -92,18 +92,17 @@ static void it8213_set_piomode (struct ata_port *ap, struct ata_device *adev)
 			    { 2, 1 },
 			    { 2, 3 }, };
 
-	if (pio > 2)
-		control |= 1;	/* TIME1 enable */
+	if (pio > 1)
+		control |= 1;	/* TIME */
 	if (ata_pio_need_iordy(adev))	/* PIO 3/4 require IORDY */
-		control |= 2;	/* IORDY enable */
+		control |= 2;	/* IE */
 	/* Bit 2 is set for ATAPI on the IT8213 - reverse of ICH/PIIX */
 	if (adev->class != ATA_DEV_ATA)
-		control |= 4;
+		control |= 4;	/* PPE */
 
 	pci_read_config_word(dev, idetm_port, &idetm_data);
 
-	/* Enable PPE, IE and TIME as appropriate */
-
+	/* Set PPE, IE, and TIME as appropriate */
 	if (adev->devno == 0) {
 		idetm_data &= 0xCCF0;
 		idetm_data |= control;

@@ -112,17 +111,17 @@ static void it8213_set_piomode (struct ata_port *ap, struct ata_device *adev)
 	} else {
 		u8 slave_data;
 
-		idetm_data &= 0xCC0F;
+		idetm_data &= 0xFF0F;
 		idetm_data |= (control << 4);
 
 		/* Slave timing in separate register */
 		pci_read_config_byte(dev, 0x44, &slave_data);
 		slave_data &= 0xF0;
-		slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << 4;
+		slave_data |= (timings[pio][0] << 2) | timings[pio][1];
 		pci_write_config_byte(dev, 0x44, slave_data);
 	}
 
-	idetm_data |= 0x4000;	/* Ensure SITRE is enabled */
+	idetm_data |= 0x4000;	/* Ensure SITRE is set */
 	pci_write_config_word(dev, idetm_port, idetm_data);
 }
 

@@ -173,10 +172,10 @@ static void it8213_set_dmamode (struct ata_port *ap, struct ata_device *adev)
 
 		udma_enable |= (1 << devid);
 
-		/* Load the UDMA mode number */
+		/* Load the UDMA cycle time */
 		pci_read_config_word(dev, 0x4A, &udma_timing);
 		udma_timing &= ~(3 << (4 * devid));
-		udma_timing |= (udma & 3) << (4 * devid);
+		udma_timing |= u_speed << (4 * devid);
 		pci_write_config_word(dev, 0x4A, udma_timing);
 
 		/* Load the clock selection */

@@ -211,7 +210,7 @@ static void it8213_set_dmamode (struct ata_port *ap, struct ata_device *adev)
 			master_data &= 0xFF4F;  /* Mask out IORDY|TIME1|DMAONLY */
 			master_data |= control << 4;
 			pci_read_config_byte(dev, 0x44, &slave_data);
-			slave_data &= (0x0F + 0xE1 * ap->port_no);
+			slave_data &= 0xF0;
 			/* Load the matching timing */
 			slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0);
 			pci_write_config_byte(dev, 0x44, slave_data);

@@ -263,7 +262,7 @@ static int it8213_init_one (struct pci_dev *pdev, const struct pci_device_id *en
 	static const struct ata_port_info info = {
 		.flags		= ATA_FLAG_SLAVE_POSS,
 		.pio_mask	= ATA_PIO4,
-		.mwdma_mask	= ATA_MWDMA2,
+		.mwdma_mask	= ATA_MWDMA12_ONLY,
 		.udma_mask 	= ATA_UDMA4, /* FIXME: want UDMA 100? */
 		.port_ops	= &it8213_ops,
 	};

index 6932e56..9df1ff7 100644
@@ -25,6 +25,13 @@
  *		http://www.ryston.cz/petr/vlb/pdc20230b.html
  *		http://www.ryston.cz/petr/vlb/pdc20230c.html
  *		http://www.ryston.cz/petr/vlb/pdc20630.html
+ *	QDI65x0:
+ *		http://www.ryston.cz/petr/vlb/qd6500.html
+ *		http://www.ryston.cz/petr/vlb/qd6580.html
+ *
+ *	QDI65x0 probe code based on drivers/ide/legacy/qd65xx.c
+ *	Rewritten from the work of Colten Edwards <[email protected]> by
+ *	Samuel Thibault <[email protected]>
  *
  *  Unsupported but docs exist:
  *	Appian/Adaptec AIC25VL01/Cirrus Logic PD7220

@@ -35,7 +42,7 @@
  *  the MPIIX where the tuning is PCI side but the IDE is "ISA side".
  *
  *  Specific support is included for the ht6560a/ht6560b/opti82c611a/
- *  opti82c465mv/promise 20230c/20630/winbond83759A
+ *  opti82c465mv/promise 20230c/20630/qdi65x0/winbond83759A
  *
  *  Use the autospeed and pio_mask options with:
  *	Appian ADI/2 aka CLPD7220 or AIC25VL01.

@@ -672,7 +679,7 @@ static void qdi6580dp_set_piomode(struct ata_port *ap, struct ata_device *adev)
 	outb(timing, ld_qdi->timing + 2 * ap->port_no);
 	/* Clear the FIFO */
 	if (adev->class != ATA_DEV_ATA)
-		outb(0x5F, ld_qdi->timing + 3);
+		outb(0x5F, (ld_qdi->timing & 0xFFF0) + 3);
 }
 
 /**

@@ -707,7 +714,7 @@ static void qdi6580_set_piomode(struct ata_port *ap, struct ata_device *adev)
 	outb(timing, ld_qdi->timing + 2 * adev->devno);
 	/* Clear the FIFO */
 	if (adev->class != ATA_DEV_ATA)
-		outb(0x5F, ld_qdi->timing + 3);
+		outb(0x5F, (ld_qdi->timing & 0xFFF0) + 3);
 }
 
 /**

@@ -787,6 +794,7 @@ static struct ata_port_operations qdi6580_port_ops = {
 static struct ata_port_operations qdi6580dp_port_ops = {
 	.inherits	= &legacy_base_port_ops,
 	.set_piomode	= qdi6580dp_set_piomode,
+	.qc_issue	= qdi_qc_issue,
 	.sff_data_xfer	= vlb32_data_xfer,
 };
 

index 2096fb7..950da39 100644
@@ -58,7 +58,7 @@ static int marvell_pata_active(struct pci_dev *pdev)
 }
 
 /**
- *	marvell_pre_reset	-	check for 40/80 pin
+ *	marvell_pre_reset	-	probe begin
  *	@link: link
  *	@deadline: deadline jiffies for the operation
  *

index 773b159..061aa1c 100644
@@ -325,6 +325,13 @@ static struct scsi_host_template ns87415_sht = {
 	ATA_BMDMA_SHT(DRV_NAME),
 };
 
+static void ns87415_fixup(struct pci_dev *pdev)
+{
+	/* Select 512 byte sectors */
+	pci_write_config_byte(pdev, 0x55, 0xEE);
+	/* Select PIO0 8bit clocking */
+	pci_write_config_byte(pdev, 0x54, 0xB7);
+}
 
 /**
  *	ns87415_init_one - Register 87415 ATA PCI device with kernel services

@@ -371,10 +378,8 @@ static int ns87415_init_one (struct pci_dev *pdev, const struct pci_device_id *e
 	if (rc)
 		return rc;
 
-	/* Select 512 byte sectors */
-	pci_write_config_byte(pdev, 0x55, 0xEE);
-	/* Select PIO0 8bit clocking */
-	pci_write_config_byte(pdev, 0x54, 0xB7);
+	ns87415_fixup(pdev);
+
 	return ata_pci_sff_init_one(pdev, ppi, &ns87415_sht, NULL);
 }
 

@@ -384,6 +389,23 @@ static const struct pci_device_id ns87415_pci_tbl[] = {
 	{ }	/* terminate list */
 };
 
+#ifdef CONFIG_PM
+static int ns87415_reinit_one(struct pci_dev *pdev)
+{
+	struct ata_host *host = dev_get_drvdata(&pdev->dev);
+	int rc;
+
+	rc = ata_pci_device_do_resume(pdev);
+	if (rc)
+		return rc;
+
+	ns87415_fixup(pdev);
+
+	ata_host_resume(host);
+	return 0;
+}
+#endif
+
 static struct pci_driver ns87415_pci_driver = {
 	.name			= DRV_NAME,
 	.id_table		= ns87415_pci_tbl,

@@ -391,7 +413,7 @@ static struct pci_driver ns87415_pci_driver = {
 	.remove			= ata_pci_remove_one,
 #ifdef CONFIG_PM
 	.suspend		= ata_pci_device_suspend,
-	.resume			= ata_pci_device_resume,
+	.resume			= ns87415_reinit_one,
 #endif
 };
 

index 84ac503..9a8687d 100644
@@ -239,7 +239,7 @@ static int oldpiix_init_one (struct pci_dev *pdev, const struct pci_device_id *e
 	static const struct ata_port_info info = {
 		.flags		= ATA_FLAG_SLAVE_POSS,
 		.pio_mask	= ATA_PIO4,
-		.mwdma_mask	= ATA_MWDMA2,
+		.mwdma_mask	= ATA_MWDMA12_ONLY,
 		.port_ops	= &oldpiix_pata_ops,
 	};
 	const struct ata_port_info *ppi[] = { &info, NULL };

index 4401b33..4fd25e7 100644
@@ -139,9 +139,9 @@ static void radisys_set_dmamode (struct ata_port *ap, struct ata_device *adev)
 		pci_read_config_byte(dev, 0x4A, &udma_mode);
 
 		if (adev->xfer_mode == XFER_UDMA_2)
-			udma_mode &= ~ (1 << adev->devno);
+			udma_mode &= ~(2 << (adev->devno * 4));
 		else /* UDMA 4 */
-			udma_mode |= (1 << adev->devno);
+			udma_mode |= (2 << (adev->devno * 4));
 
 		pci_write_config_byte(dev, 0x4A, udma_mode);
 

index c843a1e..237a24d 100644
@@ -284,7 +284,7 @@ static struct ata_port_info rdc_port_info = {
 
 	.flags		= ATA_FLAG_SLAVE_POSS,
 	.pio_mask	= ATA_PIO4,
-	.mwdma_mask	= ATA_MWDMA2,
+	.mwdma_mask	= ATA_MWDMA12_ONLY,
 	.udma_mask	= ATA_UDMA5,
 	.port_ops	= &rdc_pata_ops,
 };

index a5e4dfe..2932998 100644
@@ -105,11 +105,20 @@ static int rz1000_init_one (struct pci_dev *pdev, const struct pci_device_id *en
 #ifdef CONFIG_PM
 static int rz1000_reinit_one(struct pci_dev *pdev)
 {
+	struct ata_host *host = dev_get_drvdata(&pdev->dev);
+	int rc;
+
+	rc = ata_pci_device_do_resume(pdev);
+	if (rc)
+		return rc;
+
 	/* If this fails on resume (which is a "cant happen" case), we
 	   must stop as any progress risks data loss */
 	if (rz1000_fifo_disable(pdev))
 		panic("rz1000 fifo");
-	return ata_pci_device_resume(pdev);
+
+	ata_host_resume(host);
+	return 0;
 }
 #endif
 

index d70ecec..8af0dc8 100644
@@ -2,7 +2,7 @@
  *    pata_sis.c - SiS ATA driver
  *
  *	(C) 2005 Red Hat
- *	(C) 2007 Bartlomiej Zolnierkiewicz
+ *	(C) 2007,2009 Bartlomiej Zolnierkiewicz
  *
  *    Based upon linux/drivers/ide/pci/sis5513.c
  * Copyright (C) 1999-2000	Andre Hedrick <[email protected]>

@@ -876,6 +876,23 @@ static int sis_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
 	return ata_pci_sff_init_one(pdev, ppi, &sis_sht, chipset);
 }
 
+#ifdef CONFIG_PM
+static int sis_reinit_one(struct pci_dev *pdev)
+{
+	struct ata_host *host = dev_get_drvdata(&pdev->dev);
+	int rc;
+
+	rc = ata_pci_device_do_resume(pdev);
+	if (rc)
+		return rc;
+
+	sis_fixup(pdev, host->private_data);
+
+	ata_host_resume(host);
+	return 0;
+}
+#endif
+
 static const struct pci_device_id sis_pci_tbl[] = {
 	{ PCI_VDEVICE(SI, 0x5513), },	/* SiS 5513 */
 	{ PCI_VDEVICE(SI, 0x5518), },	/* SiS 5518 */

@@ -891,7 +908,7 @@ static struct pci_driver sis_pci_driver = {
 	.remove			= ata_pci_remove_one,
 #ifdef CONFIG_PM
 	.suspend		= ata_pci_device_suspend,
-	.resume			= ata_pci_device_resume,
+	.resume			= sis_reinit_one,
 #endif
 };
 

index 78eac27..0d97890 100644
@@ -303,14 +303,21 @@ static void via_do_set_mode(struct ata_port *ap, struct ata_device *adev, int mo
 	}
 
 	/* Set UDMA unless device is not UDMA capable */
-	if (udma_type && t.udma) {
-		u8 cable80_status;
+	if (udma_type) {
+		u8 udma_etc;
 
-		/* Get 80-wire cable detection bit */
-		pci_read_config_byte(pdev, 0x50 + offset, &cable80_status);
-		cable80_status &= 0x10;
+		pci_read_config_byte(pdev, 0x50 + offset, &udma_etc);
 
-		pci_write_config_byte(pdev, 0x50 + offset, ut | cable80_status);
+		/* clear transfer mode bit */
+		udma_etc &= ~0x20;
+
+		if (t.udma) {
+			/* preserve 80-wire cable detection bit */
+			udma_etc &= 0x10;
+			udma_etc |= ut;
+		}
+
+		pci_write_config_byte(pdev, 0x50 + offset, udma_etc);
 	}
 }
 

index 3f0bc42..a743e68 100644
@@ -165,7 +165,7 @@ static const struct pci_device_id generic_pci_tbl[] = {
 	{ PCI_VDEVICE(TOSHIBA,	PCI_DEVICE_ID_TOSHIBA_PICCOLO_1),	 4 },
 	{ PCI_VDEVICE(TOSHIBA,	PCI_DEVICE_ID_TOSHIBA_PICCOLO_2),	 4 },
 	{ PCI_VDEVICE(TOSHIBA,	PCI_DEVICE_ID_TOSHIBA_PICCOLO_3),	 4 },
-	{ PCI_VDEVICE(TOSHIBA,	PCI_DEVICE_ID_TOSHIBA_PICCOLO_5)	 4 },
+	{ PCI_VDEVICE(TOSHIBA,	PCI_DEVICE_ID_TOSHIBA_PICCOLO_5),	 4 },
 	{ PCI_VDEVICE(NETCELL,	PCI_DEVICE_ID_REVOLUTION),		 6 },
 	/*
 	 * Must come last.  If you add entries adjust