Skip to content

omap: Board specific muxing using hwmod

Tony Lindgren linux-arm-kernel linux-omap 1 version New

Get series with b4
b4 am [email protected]

Versions newest first

  1. v1 Latest6 patches 0 repliesNew

Patches in v1 No applies recorded yet

#Subject and filesSizeRepliesApplied
1/6omap2+: Add omap_mux_get_by_namearch/arm/mach-omap2/mux.c+48 -250 replies
2/6omap2+: Add support for hwmod specific muxing of devicesarch/arm/mach-omap2/mux.c arch/arm/mach-omap2/mux.h arch/arm/plat-omap/include/plat/omap_hwmod.h+123 -00 replies
2/6omap2+: Add support for hwmod specific muxing of devicesarch/arm/mach-omap2/mux.c arch/arm/mach-omap2/mux.h arch/arm/plat-omap/include/plat/omap_hwmod.h+118 -00 replies
3/6omap2+: Allow hwmod state changes to mux pads based on the state changesarch/arm/mach-omap2/mux.c arch/arm/mach-omap2/mux.h arch/arm/mach-omap2/omap_hwmod.c+74 -30 replies
3/6omap2+: Allow hwmod state changes to mux pads based on the state changesarch/arm/mach-omap2/mux.c arch/arm/mach-omap2/mux.h arch/arm/mach-omap2/omap_hwmod.c+74 -30 replies
4/6omap2+: Add struct omap_device_board_data and allow omap_device_build initialize pads to muxarch/arm/mach-omap2/devices.c arch/arm/mach-omap2/gpio.c arch/arm/mach-omap2/pm.c +4 more+37 -110 replies
4/6omap2+: Add struct omap_device_board_data and allow omap_device_build initialize pads to mux+0 -00 replies
5/6omap2+: Use omap_device_board_data for platform level serial initarch/arm/mach-omap2/serial.c arch/arm/plat-omap/include/plat/serial.h+22 -100 replies
5/6omap2+: Use omap_device_board_data for platform level serial initarch/arm/mach-omap2/mux.h arch/arm/mach-omap2/serial.c arch/arm/plat-omap/include/plat/serial.h+38 -90 replies
6/6omap2+: Initialize serial ports for wake-up events for n8x0arch/arm/mach-omap2/board-n8x0.c+63 -31 reply
6/6omap2+: Initialize serial ports for wake-up events for n8x0+0 -00 replies
6/6omap2+: Initialize serial ports for wake-up events for n8x0arch/arm/mach-omap2/board-n8x0.c+38 -20 replies

Reviews trailers per patch

No Reviewed-by, Acked-by or Tested-by trailers for v1 yet.

Read the v1 thread

Cover letter [PATCH 0/6] omap: Board specific muxing using hwmod

Hi all,

Here are some patches to allow us to pass the board specific mux data to the platform level device init code, and then allow hwmod state changes to do the pin muxing.

Dynamic remuxing is also supported as needed, the last patch in this series sets up the board-*.c data for n8x0 to do uart3 rx pin remuxing for the idle modes.

Regards,

Tony

---

Tony Lindgren (6):
omap2+: Add omap_mux_get_by_name
omap2+: Add support for hwmod specific muxing of devices
omap2+: Allow hwmod state changes to mux pads based on the state changes omap2+: Add struct omap_device_board_data and allow omap_device_build initialize pads to mux omap2+: Use omap_device_board_data for platform level serial init
omap2+: Initialize serial ports for wake-up events for n8x0

 arch/arm/mach-omap2/board-n8x0.c              |   66 ++++++++-
 arch/arm/mach-omap2/devices.c                 |    2 
 arch/arm/mach-omap2/gpio.c                    |    2 
 arch/arm/mach-omap2/mux.c                     |  188 ++++++++++++++++++++++---
 arch/arm/mach-omap2/mux.h                     |   39 +++++
 arch/arm/mach-omap2/omap_hwmod.c              |   14 +-
 arch/arm/mach-omap2/pm.c                      |    3 
 arch/arm/mach-omap2/serial.c                  |   29 +++-
 arch/arm/plat-omap/i2c.c                      |    4 -
 arch/arm/plat-omap/include/plat/omap_device.h |   19 ++-
 arch/arm/plat-omap/include/plat/omap_hwmod.h  |   32 ++++
 arch/arm/plat-omap/include/plat/serial.h      |    5 +
 arch/arm/plat-omap/omap_device.c              |   14 ++
 13 files changed, 366 insertions(+), 51 deletions(-)
Signature · 1 line
Signature