Skip to content

mtd: spi-nor: add a new framework for SPI NOR

Marek Vasut linux-arm-kernel linux-mtd linux-spi 1 version New

Get series with b4
b4 am [email protected]

Versions newest first

  1. v1 Latest0 of 4 patches 0 repliesNew

Patches in v1 No applies recorded yet

None of the 4 patches the cover letter announces are in this archive.

Reviews trailers per patch

No Reviewed-by, Acked-by or Tested-by trailers for v1 yet.

Read the v1 thread

Cover letter [PATCH 0/4] mtd: spi-nor: add a new framework for SPI NOR

Dear Sourav Poddar,

Quoted 103 lines

Dear Marek Vasut,

Quoted 41 lines · Marek Vasut

Dear Sourav Poddar,

Quoted 39 lines

Dear Marek Vasut,

Quoted 24 lines · Marek Vasut

Dear Sourav Poddar,

Quoted 22 lines

Dear Marek Vasut, Huang,

Quoted 4 lines · Marek Vasut

Dear Huang Shijie,

Quoted 2 lines

1.) Why add a new framework for SPI NOR?

Quoted 8 lines
Quoted 4 lines

The SPI-NOR controller such as Freescale's Quadspi controller is working in a different way from the SPI bus. It should knows the NOR commands to find the right LUT sequence. Unfortunately, the current code can not meet this requirement.

Is there any kind of documentation for this controller available? I cannot quite understand how this controller works and why can it not be used with our current infrastructure.

I do have a similar requirement where my controller need to be configured from slave info. I have submiited a series in the mtd list adding that portion
of handling such cases. Here, is the patch which specific to m25p80 part. http://patchwork.ozlabs.org/patch/294285/

Quoted 4 lines
Quoted 2 lines

The whole series can be found here:
https://www.mail-archive.com/linux-omap at vger.kernel.org/msg98691.html

Is this TI QSPI the same thing as the Altera QSPI controller please ?

No, its differenet.

Quoted 4 lines

Otherwise, I seriously believe you and Huang should work on a common infrastructure. I would first like to understand how is the controller in DRA7xx different from regular SPI controller though. Is there any kind of documentation I could study please?

Quoted 4 lines
Quoted 1 line

Sorry, we dont have a public document yet.

Sorry for the delayed reply. I am processing the input on the QSPI and I'm finally starting to understand what's going on in here.

Thanks for the response.

Quoted 39 lines
Quoted 39 lines

Though, this is what ti qspi contoller has

It supports two modes of operation, one is SPI mode(normal), other is the memory mapped read mode.

For SPI mode, the state machine remains the same as it is with other spi controller
available.

For memory mapped, there is something more which we need to do around ..

1. There is a qspi "set up" register available, which needs to be filled with

information like flash opcode, dummy bytes etc. In short, flash

specific

details.

2 if the above register is configured with the required opcodes, then
whenever

we need to use memory mapped operations, we need to do is to

switch our

qspi controller to memory mapped mode.

Switching of this mode to memory mapped needs

a ) write to a particular qspi register
b) write to control module(optional based on SOC).

3. Once the above steps are configured, then the flash data will be mapped to a

particular memory address(SOC specific) from where the flash data

Quoted 7 lines
Quoted 1 line

can be read.

OK, but is the memory mapped mode of any use (but for booting I suppose) ? How does it handle large SPI NOR flashes (we have spansion devices as big as 128MiB), does it really hog a _large_ amount of address space from the CPU address space ? Or is the operation somehow indexed ? Why is it better than using DMA?

Memory mapped will be of use whenever we try to read the flash content. Instead of going through the entire SPI framework, and raising interrupts, we can
memcpy the flash contents. I am using it for mounting a jffs2 filesystem.

Quoted 8 lines

For me the memory mapped regions are like in the range 5c000000 - 5fffffff, so
I can handle flash as large as 64MB.

As far as its comparison with DMA is concerned, I cant comment much about it.
My Qspi controller does not support DMA :(:(. So, memory mapped becomes the best option option for me.

OK, understood. So to sling large chunks of memory from SPI NOR to your DRAM, you need to issue these two steps in a loop:

1) write into the controller register the starting address of the SPI flash which you want to have available via the mmap interface
2) memcpy() from this mmaped area to DRAM

correct? Won't the second step be pretty CPU-intensive?