Skip to content

mtd: gpmi: add subpage read support

Huang Shijie linux-arm-kernel linux-mtd 1 version New

Get series with b4
b4 am [email protected]

Versions newest first

  1. v1 Latest0 of 3 patches 0 repliesNew

Patches in v1 No applies recorded yet

None of the 3 patches the cover letter announces are in this archive.

Reviews trailers per patch

No Reviewed-by, Acked-by or Tested-by trailers for v1 yet.

Read the v1 thread

Cover letter [PATCH 0/3] mtd: gpmi: add subpage read support
Quoted 85 lines · Huang Shijie

1) Why add the subpage read support?
The page size of the nand chip becomes larger and larger, the imx6 has to supports the 16K page or even bigger page. But sometimes, the upper layer only needs a small part of the page, such as 512 bytes or less.

For example, ubiattach may only read 64 bytes per page.

2) We only enable the subpage read support when it meets the conditions:
<1> the chip is imx6 (or later chips) which can supports large nand page. <2> the size of ECC parity is byte aligned.
If the size of ECC parity is not byte aligned, the calling of NAND_CMD_RNDOUT will fail.

3) What does this patch set do?
patch 1: add a new argument for read_subpage hook
patch 2: do not use the mtd->writesize.
patch 3: This patch will fake a virtual small page for the subpage read,
and call the gpmi_ecc_read_page() to do the real work. In order to fake a virtual small page, the patch changes the BCH registers and the bch_geometry{}. After the subpage read finished, we will restore them back.

4) Performace:

    4.1) Tested with Toshiba TC58NVG2S0F(4096 + 224) with the following command:
         #ubiattach /dev/ubi_ctrl -m 4

       The detail information of /dev/mtd4 shows below:
       --------------------------------------------------------------
       #mtdinfo /dev/mtd4
        mtd4
        Name:                           test
        Type:                           nand
        Eraseblock size:                262144 bytes, 256.0 KiB
        Amount of eraseblocks:          1856 (486539264 bytes, 464.0 MiB)
        Minimum input/output unit size: 4096 bytes
        Sub-page size:                  4096 bytes
        OOB size:                       224 bytes
        Character device major/minor:   90:8
        Bad blocks are allowed:         true
        Device is writable:             true
       --------------------------------------------------------------

    4.2) Before this patch:
       --------------------------------------------------------------
       [   94.530495] UBI: attaching mtd4 to ubi0
       [   98.928850] UBI: scanning is finished
       [   98.953594] UBI: attached mtd4 (name "test", size 464 MiB) to ubi0
       [   98.958562] UBI: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
       [   98.964076] UBI: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
       [   98.969518] UBI: VID header offset: 4096 (aligned 4096), data offset: 8192
       [   98.975128] UBI: good PEBs: 1856, bad PEBs: 0, corrupted PEBs: 0
       [   98.979843] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
       [   98.985878] UBI: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 2024916145
       [   98.993635] UBI: available PEBs: 0, total reserved PEBs: 1856, PEBs reserved for bad PEB handling: 40
       [   99.001807] UBI: background thread "ubi_bgt0d" started, PID 831
       --------------------------------------------------------------
       The attach time is about 98.9 - 94.5 = 4.4s

    4.3) After this patch:
       --------------------------------------------------------------
       [  286.464906] UBI: attaching mtd4 to ubi0
       [  289.186129] UBI: scanning is finished
       [  289.211416] UBI: attached mtd4 (name "test", size 464 MiB) to ubi0
       [  289.216360] UBI: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes
       [  289.221858] UBI: min./max. I/O unit sizes: 4096/4096, sub-page size 4096
       [  289.227293] UBI: VID header offset: 4096 (aligned 4096), data offset: 8192
       [  289.232878] UBI: good PEBs: 1856, bad PEBs: 0, corrupted PEBs: 0
       [  289.237628] UBI: user volume: 0, internal volumes: 1, max. volumes count: 128
       [  289.243553] UBI: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 2024916145
       [  289.251348] UBI: available PEBs: 1812, total reserved PEBs: 44, PEBs reserved for bad PEB handling: 40
       [  289.259417] UBI: background thread "ubi_bgt0d" started, PID 847
       --------------------------------------------------------------
       The attach time is about 289.18 - 286.46 = 2.7s

     4.4) The conclusion:
       We achieve (4.4 - 2.7) / 4.4 = 38.6% faster in the ubiattach.

5) This patch depends on the following patch:

    http://lists.infradead.org/pipermail/linux-mtd/2013-December/051091.html

Huang Shijie (3):
mtd: nand: add "page" argument for read_subpage hook
mtd: gpmi: do not use the mtd->writesize
mtd: gpmi: add subpage read support

Quoted 9 lines
 drivers/mtd/nand/gpmi-nand/gpmi-nand.c |  102 +++++++++++++++++++++++++++++++-
 drivers/mtd/nand/nand_base.c           |    7 ++-
 include/linux/mtd/nand.h               |    2 +-
 3 files changed, 105 insertions(+), 6 deletions(-)
Signature · 1 line
1.7.2.rc3

just a ping.

Best Regards
Huang Shijie