Skip to content

IR support for A83T

Philipp Rossak linux-arm-kernel linux-devicetree linux-media lkml 8 versions – In review

Get series with b4
b4 am [email protected]

Versions newest first · linked by author and title

  1. v7 Latest4 patches 1 replyIn review
  2. v64 patches 3 repliesSuperseded
  3. v5 posting 2/26 patches 4 repliesSuperseded
Earlier versions · 5
VersionPostedPatchesRepliesStatus
v5 posting 1/26 patches2 repliesSuperseded
v45 of 6 patches2 repliesSuperseded
v36 patches7 repliesSuperseded
v26 patches2 repliesSuperseded
v15 patches7 repliesSuperseded

Changes in v7 from the cover letter

* update Acked-by
* add missing a83t compatile on patch 2

Patches in v7 No applies recorded yet

#Subject and filesSizeRepliesApplied
1/4ARM: dts: sun8i: a83t: Add the cir pin for the A83Tarch/arm/boot/dts/sun8i-a83t.dtsi+5 -00 replies
2/4ARM: dts: sun8i: a83t: Add support for the cir interfacearch/arm/boot/dts/sun8i-a83t.dtsi+13 -00 replies
3/4ARM: dts: sun8i: a83t: bananapi-m3: Enable IR controllerarch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts+5 -00 replies
4/4ARM: dts: sun8i: h3-h5: ir register size should be the whole memory blockarch/arm/boot/dts/sunxi-h3-h5.dtsi+1 -10 replies

Reviews trailers per patch

All 4 patches have a Reviewed-by or Acked-by.

PatchMaxime RipardChen-Yu Tsai
1/4A-b
2/4A-b
3/4A-b A-b
4/4A-b

Trailers given in replies are filled; those carried in the patches from earlier versions are outlined with dashes.

Read the v7 thread

Cover letter [PATCH v7 0/4] IR support for A83T

This patch series adds support for the sunxi A83T ir module and enhances the sunxi-ir driver. Right now the base clock frequency for the ir driver is a hard coded define and is set to 8 MHz.
This works for the most common ir receivers. On the Sinovoip Bananapi M3 the ir receiver needs, a 3 MHz base clock frequency to work without problems with this driver.

This patch series adds support for an optinal property that makes it able to override the default base clock frequency and enables the ir interface on the a83t and the Bananapi M3.

changes since v6:
* update Acked-by
* add missing a83t compatile on patch 2

changes since v5:
* removed already merged patches
* adapt patch 2 to be applyable to current rc-1

changes since v4:
* rename cir pin from cir_pins to r_cir_pin
* drop unit-address from r_cir_pin
* add a83t compatible to the cir node
* move muxing options to dtsi
* rename cir label and reorder it in the bananpim3.dts file

changes since v3:
* collecting all acks & reviewd by
* fixed typos

changes since v2:
* reorder cir pin (alphabetical)
* fix typo in documentation

changes since v1:
* fix typos, reword Documentation
* initialize 'b_clk_freq' to 'SUNXI_IR_BASE_CLK' & remove if statement
* change dev_info() to dev_dbg()
* change naming to cir* in dts/dtsi
* Added acked Ackedi-by to related patch
* use whole memory block instead of registers needed + fix for h3/h5

changes since rfc:
* The property is now optinal. If the property is not available in the dtb the driver uses the default base clock frequency.
* the driver prints out the the selected base clock frequency.
* changed devicetree property from base-clk-frequency to clock-frequency

Regards,
Philipp

Philipp Rossak (4):
ARM: dts: sun8i: a83t: Add the cir pin for the A83T
ARM: dts: sun8i: a83t: Add support for the cir interface
ARM: dts: sun8i: a83t: bananapi-m3: Enable IR controller
ARM: dts: sun8i: h3-h5: ir register size should be the whole memory
block

 arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts |  5 +++++
 arch/arm/boot/dts/sun8i-a83t.dtsi            | 18 ++++++++++++++++++
 arch/arm/boot/dts/sunxi-h3-h5.dtsi           |  2 +-
 3 files changed, 24 insertions(+), 1 deletion(-)
Signature · 1 line
2.11.0