Skip to content

Fixing MMC access on Raspberry Pi CM3

Tomaz Solc barebox 2 versions – Applied

Status from this message: Applied, thanks

Get series with b4
b4 am [email protected]

Versions newest first · linked by author and title

  1. v2 Latest8 patches 1 replyApplied
  2. v17 patches 4 repliesSuperseded

Patches in v2 Applied

#Subject and filesSizeRepliesApplied
1/8ARM: rpi: switch emmc from sdhost to sdhciarch/arm/dts/bcm2837-rpi-3.dts+9 -00 replies
2/8Kconfig: add pin controllers submenu.drivers/pinctrl/Kconfig+4 -00 replies
3/8pinctrl: bcm2835: move existing code from gpio.arch/arm/configs/rpi_defconfig drivers/gpio/Kconfig drivers/gpio/Makefile +3 more+8 -60 replies
4/8pinctrl: bcm2835: register the pin controller.drivers/pinctrl/pinctrl-bcm2835.c+51 -10 replies
5/8mci: bcm2835: use device_initcall(), not coredev.drivers/mci/mci-bcm2835.c+1 -10 replies
6/8mci: bcm2835: parse other device tree properties.drivers/mci/mci-bcm2835.c+3 -00 replies
7/8ARM: rpi: Add device tree for Compute Module 3.arch/arm/boards/raspberry-pi/lowlevel.c arch/arm/dts/Makefile arch/arm/dts/bcm2837-rpi-cm3.dts +2 more+40 -10 replies
8/8ARM: rpi: add CONFIG_PINCTRL to rpi_defconfig.arch/arm/configs/rpi_defconfig+1 -10 replies

Reviews trailers per patch

No Reviewed-by, Acked-by or Tested-by trailers for v2 yet.

Read the v2 thread

Cover letter [PATCH v2 0/8] Fixing MMC access on Raspberry Pi CM3

Changes from the first patch series:

- Base Compute Module 3 device tree off upstream device tree for CM3 + IO3 dev board, instead of R. Pi 3B.
- Keep Makefile.bcm283x without a newline at the end of file.
- Make mci init before pinctrl by moving mci-bcm2835 to device_initcall() instead of changing link order.
- Add CONFIG_PINCTRL to rpi_defconfig.

Best regards
Tomaz

Tomaz Solc (8):
ARM: rpi: switch emmc from sdhost to sdhci
Kconfig: add pin controllers submenu.
pinctrl: bcm2835: move existing code from gpio.
pinctrl: bcm2835: register the pin controller.
mci: bcm2835: use device_initcall(), not coredev.
mci: bcm2835: parse other device tree properties.
ARM: rpi: Add device tree for Compute Module 3.
ARM: rpi: add CONFIG_PINCTRL to rpi_defconfig.

 arch/arm/boards/raspberry-pi/lowlevel.c            | 10 +++++
 arch/arm/configs/rpi_defconfig                     |  4 +-
 arch/arm/dts/Makefile                              |  1 +
 arch/arm/dts/bcm2837-rpi-3.dts                     |  9 ++++
 arch/arm/dts/bcm2837-rpi-cm3.dts                   | 18 ++++++++
 arch/arm/mach-bcm283x/Kconfig                      |  6 +++
 drivers/gpio/Kconfig                               |  4 --
 drivers/gpio/Makefile                              |  1 -
 drivers/mci/mci-bcm2835.c                          |  5 ++-
 drivers/pinctrl/Kconfig                            | 10 +++++
 drivers/pinctrl/Makefile                           |  1 +
 .../gpio-bcm2835.c => pinctrl/pinctrl-bcm2835.c}   | 52 +++++++++++++++++++++-
 images/Makefile.bcm283x                            |  6 ++-
 13 files changed, 117 insertions(+), 10 deletions(-)
 create mode 100644 arch/arm/dts/bcm2837-rpi-cm3.dts
 rename drivers/{gpio/gpio-bcm2835.c => pinctrl/pinctrl-bcm2835.c} (77%)
Signature · 7 lines
2.11.0


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox