sunxi: H6: Enable USB (2.0) support
Get series with b4
b4 am [email protected]Versions newest first
- v1 Latest0 of 6 patches 0 repliesNew
Patches in v1 No applies recorded yet
None of the 6 patches the cover letter announces are in this archive.
Reviews trailers per patch
No Reviewed-by, Acked-by or Tested-by trailers for v1 yet.
Cover letter [U-Boot] [linux-sunxi] [PATCH 0/6] sunxi: H6: Enable USB (2.0) support
On Wed, 19 Jun 2019 10:57:14 +0200
Clément Péron <[email protected]> wrote:
Hi,
Quoted 43 lines · André Przywara
Quoted 42 lines
On Tue, 18 Jun 2019 19:22:34 +0200
Clément Péron <[email protected]> wrote:Hi,
Quoted 35 lines · Clément Péron
Quoted 34 lines
Hi Andre,
Quoted 27 lines · Jagan Teki
Quoted 25 lines · Andre Przywara
Hi,
this series enables USB support on the H6 boards. This is mostly just adding some missing pieces here and there, the actual controller and PHY are very similar to the previous ones, if not identical. This is for the 2.0 ports only at the moment, USB 3.0 will be done later (started porting Icenowy's Linux driver).
The Pine H64 shares a similar problem as the Pine64+ boards regarding the upper USB port. To enable this port, we need the first patch from the series [1] fixing this issue on the A64 boards.Patch 1 is a drive-by patch to bring
SUNXI_GPIOtoKconfig, as this was lingering in one of my branches for a while.
Patch 2 enables GPIO support for the H6, as this is needed for the Pine H64 to enable the VBUS regulator.
Patch 3 adds the clock and reset gates mappings for the USB controller and the PHY, the values are taken from the manual and verified against Linux.
Patch 4 adds some code to the PHY driver to skip over not implemented PHYs, as the H6 uses a PHY0/PHY3 combination in the DT.
Patch 5 then eventually enables USB in the existing defconfigs. Patch 6 adds the .dts fixes required to get the upper USB port to work on the Pine H64.Quoted 1 line
Quoted 1 line
Clément, can you please verify that this works for the Beelink box?
Thank you for the notice.
Quoted 7 lines
Quoted 5 lines
Quoted 3 lines
Quoted 1 line
Works fine on my board:
I have tested with and without the trick in usb2otg node and both seems working. (only tested usb start; usb tree).
You mean dropping the status="okay"?
I mean, I have tested with and without the whole patch and it works in both cases.
Do you mean it works without adding "phys = <&usb2phy 0>;" to the ehci0 and ohci0 nodes?
Are you sure that USB *really* works? The boot log *always* enumerates the bus and prints one device (the root hub), but does "usb tree" show an actual connected device? The easiest test is to connect a pen drive, at which point U-Boot automatically lists the USB mass storage device in the boot log.
Quoted 11 lines
Quoted 9 lines
Yeah, I figured as well that it works both ways. Actually older kernels require the MUSB driver to be enabled, while newer kernels don't seem to care. As this affects the Debian Buster kernel (4.19, in the installer), I plan on just leaving it as it is right now.
Quoted 1 line
Why not leave it to avoid a difference with linux?
Technically we should disable it, as it's not usable and might clash with EHCI0/OHCI0, but for said reason I just keep it.
That's what I have in mind, if it's not mandatory just leave it as this, this will avoid differences with linux.
There shall be no real differences with Linux, in this case I will push those changes to Linux, so we sync this somewhat the other way. The hardware clearly connects the USB0 controller to PHY0, the DT should reflect this.
Cheers,
Andre.
Quoted 39 lines
Quoted 39 lines
Quoted 38 lines
Quoted 38 lines
U-Boot 2019.07-rc4 (Jun 18 2019 - 19:06:21 +0200) Allwinner Technology
CPU: Allwinner H6 (SUN50I) Model: Beelink GS1 DRAM: 2 GiB MMC: mmc at 4020000: 0, mmc at 4022000: 1 Loading Environment from FAT... Unable to use mmc 1:1... In: serial at 5000000 Out: serial at 5000000 Err: serial at 5000000 Net: No ethernet found.starting USB...
Bus usb at 5101000: USB EHCI 1.00
Bus usb at 5101400: USB OHCI 1.0
scanning bus usb at 5101000 for devices... 1 USB Device(s) foundRegards,
ClémentQuoted 20 lines
Quoted 9 lines
I guess the USB 2.0 port is probably the OTG one, so this setup would look somewhat similar to the PineH64, which would allow you to copy the USB DT nodes from there.
Cheers,
Andre.[1] https://lists.denx.de/pipermail/u-boot/2019-May/369520.html
Quoted 7 lines
Andre Przywara (6):
sunxi: moveSUNXI_GPIOtoKconfig
sunxi: gpio: Enable support for H6 pin controller
sunxi: clocks: Add H6 USB clock gates and resets
sunxi: phy: Add USB PHY support for Allwinner H6
sunxi: H6: Enable USB for existing boards
sunxi: Pine64: DTS: enable USB PHY 0 for HCI0Except 6/6 (it can be part of DTS sync during MW) and rest
Reviewed-by Jagan Teki <[email protected]>