Skip to content

sunxi: H6: Enable USB (2.0) support

Corentin Labbe u-boot 1 version New

Get series with b4
b4 am 20190624101438.GA20546@Red

Versions newest first

  1. v2 Latest0 of 5 patches 0 repliesNew

Patches in v2 No applies recorded yet

None of the 5 patches the cover letter announces are in this archive.

Reviews trailers per patch

PatchCorentin Labbe
SeriesT-b

Trailers given in replies are filled; those carried in the patches from earlier versions are outlined with dashes.

Read the v2 thread

Cover letter [U-Boot] [linux-sunxi] [PATCH v2 0/5] sunxi: H6: Enable USB (2.0) support
Quoted 29 lines · Andre Przywara

Hi,

a minor update to v1, adding PortM support as per Icenowy's comment and dropping the DT change. We still need the latter for support the USB0 port on some boards, but this takes another route now (syncing back from Linux).
---------------

This series enables USB support on the H6 boards. This is mostly just adding some missing pieces here and there, the actual controller and PHY are very similar to the previous ones, if not identical. This is for the 2.0 ports only at the moment, USB 3.0 requires some more work to make U-Boot's driver compliant to the kernel's DT bindings.

The Pine H64 shares a similar problem as the Pine64+ boards regarding the upper USB port. To enable this port, we need a patch from Paul [1] and changes to the DT [2]. But this is orthogonal to this series.

Patch 1 is a drive-by patch to bring SUNXI_GPIO to Kconfig, as this was lingering in one of my branches for a while.
Patch 2 enables GPIO support for the H6, as this is needed for the Pine H64 to enable the VBUS regulator.
Patch 3 adds the clock and reset gates mappings for the USB controller and the PHY, the values are taken from the manual and verified against Linux.
Patch 4 adds some code to the PHY driver to skip over not implemented PHYs, as the H6 uses a PHY0/PHY3 combination in the DT.
Patch 5 then eventually enables USB in the existing defconfigs.

Quoted 3 lines

Cheers,
Andre.

Hello

I have tested your serie on a orangepi1+ and it works!

But on a pineH64 with an asix USb dongle I got:
U-Boot SPL 2019.07-rc4-00183-g6b5b853fd8-dirty (Jun 24 2019 - 10:44:19 +0200)
DRAM: 2048 MiB
Trying to boot from MMC1

NOTICE:  BL31: v2.1(release):v2.1-72-g4b9d01d5
NOTICE:  BL31: Built : 11:47:12, Apr 16 2019
NOTICE:  BL31: Detected Allwinner H6 SoC (1728)
NOTICE:  BL31: Found U-Boot DTB at 0xc07fa00, model: Pine H64
NOTICE:  PMIC: Probing AXP805
NOTICE:  PMIC: AXP805 detected

U-Boot 2019.07-rc4-00183-g6b5b853fd8-dirty (Jun 24 2019 - 10:44:19 +0200) Allwinner Technology

CPU:   Allwinner H6 (SUN50I)
Model: Pine H64
DRAM:  2 GiB
MMC:   mmc at 4020000: 0, mmc at 4022000: 1
Loading Environment from FAT... Card did not respond to voltage select!
In:    serial at 5000000
Out:   serial at 5000000
Err:   serial at 5000000
Net:   No ethernet found.

starting USB...
Bus usb at 5101000: USB EHCI 1.00
Bus usb at 5101400: USB OHCI 1.0
Bus usb at 5311000: USB EHCI 1.00
Bus usb at 5311400: USB OHCI 1.0
scanning bus usb at 5101000 for devices... 1 USB Device(s) found scanning bus usb at 5101400 for devices... 1 USB Device(s) found scanning bus usb at 5311000 for devices...
Warning: ax88179_eth MAC addresses don't match:
Address in ROM is 00:0e:c6:ac:f3:d0
Address in environment is 02:01:1b:e5:f7:26
2 USB Device(s) found
scanning bus usb at 5311400 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
=> dhcp
Waiting for Ethernet connection... unable to connect. Reset Ethernet Device
Waiting for Ethernet connection... done.
BOOTP broadcast 1
EHCI timed out on TD - token=0x14008d80
Rx: failed to receive: -5
BOOTP broadcast 2
DHCP client bound to address 192.168.66.143 (6010 ms)
*** ERROR: `serverip' not set
Cannot autoload with TFTPGET

But the network is working (download kernel via tftp with success) But I fear the EHCI timed out and co...
Could it be related to yours patchs ?

Anyway you could add

Thanks
Regards