RFC ethtool: Add support for frame preemption
Get series with b4
b4 am [email protected]Versions newest first
- v1 RFC Latest4 patches 35 repliesIn review
Patches in v1 No applies recorded yet
| # | Subject and files | Size | Replies | Applied |
|---|---|---|---|---|
| 1/4 | ethtool: Add support for configuring frame preemptioninclude/ include/ net/ | +67 | 1 reply | |
| 2/4 | ethtool: Add support for configuring frame preemption via netlinkinclude/ net/ net/ +2 more | +219 | 1 reply | |
| 3/4 | igc: Add support for configuring frame preemptiondrivers/ drivers/ drivers/ +1 more | +118 | 1 reply | |
| 4/4 | igc: Add support for exposing frame preemption stats registersdrivers/ drivers/ | +19 | 1 reply |
Reviews trailers per patch
No Reviewed-by, Acked-by or Tested-by trailers for v1 yet.
Cover letter [next-queue RFC 0/4] ethtool: Add support for frame preemption
Hi,
This series adds support for configuring frame preemption, as defined by IEEE 802.1Q-2018 (previously IEEE 802.1Qbu) and IEEE 802.3br.
Frame preemption allows a packet from a higher priority queue marked as "express" to preempt a packet from lower priority queue marked as "preemptible". The idea is that this can help reduce the latency for higher priority traffic.
Previously, the proposed interface for configuring these features was using the qdisc layer. But as this is very hardware dependent and all that qdisc did was pass the information to the driver, it makes sense to have this in ethtool.
One example, for retrieving and setting the configuration:
$ ethtool $ sudo ./ethtool --show-frame-preemption enp3s0 Frame preemption settings for enp3s0: support: supported active: active supported queues: 0xf supported queues: 0xe minimum fragment size: 68
$ ethtool --set-frame-preemption enp3s0 fp on min-frag-size 68 preemptible-queues-mask 0xe
This is a RFC because I wanted to have feedback on some points:
- The parameters added are enough for the hardware I have, is it enough in general?
- even with the ethtool via netlink effort, I chose to keep the ioctl() way, in case someone wants to backport this to an older kernel, is there a problem with this?
- Some space for bikeshedding the names and location (for example, does it make sense for these settings to be per-queue?), as I am not quite happy with them, one example, is the use of preemptible vs. preemptable;
About the patches, should be quite straightforward:
Patch 1, adds the ETHTOOL_GFP and ETHOOL_SFP commands and the associated data structures;
Patch 2, adds the ETHTOOL_MSG_PREEMPT_GET and ETHTOOL_MSG_PREEMPT_SET netlink messages and the associated attributes;
Patch 3, is the example implementation for the igc driver, the catch here is that frame preemption in igc is dependent on the TSN "mode" being enabled;
Patch 4, adds some registers that helped during implementation.
Another thing is that because igc is still under development, to avoid conflicts, I think it might be easier for the PATCH version of this series to go through Jeff Kirsher's tree.
Vinicius Costa Gomes (4):
ethtool: Add support for configuring frame preemption
ethtool: Add support for configuring frame preemption via netlink
igc: Add support for configuring frame preemption
igc: Add support for exposing frame preemption stats registers
drivers/net/ethernet/intel/igc/igc.h | 3 + drivers/net/ethernet/intel/igc/igc_defines.h | 6 + drivers/net/ethernet/intel/igc/igc_ethtool.c | 77 ++++++++ drivers/net/ethernet/intel/igc/igc_regs.h | 10 + drivers/net/ethernet/intel/igc/igc_tsn.c | 46 ++++- include/linux/ethtool.h | 6 + include/uapi/linux/ethtool.h | 25 +++ include/uapi/linux/ethtool_netlink.h | 19 ++ net/ethtool/Makefile | 3 +- net/ethtool/ioctl.c | 36 ++++ net/ethtool/netlink.c | 15 ++ net/ethtool/netlink.h | 2 + net/ethtool/preempt.c | 181 +++++++++++++++++++ 13 files changed, 423 insertions(+), 6 deletions(-) create mode 100644 net/ethtool/preempt.c
Signature · 1 line
2.26.2