Skip to content

Galaxycore GC5035 sensor driver

Tomasz Figa linux-devicetree linux-media lkml 1 version In review

Get series with b4
b4 am [email protected]

Versions newest first

  1. v4 Latest4 patches 4 repliesIn review

Changes in v4 from the cover letter

- Require and handle clock-frequency and link-frequencies device properties.
- Separate the driver patch into one for base functionality and another for OTP handling.
- Do not perform OTP initialization on driver probe, since it's a costly operation. Instead do it at first streaming time.
- Fix power sequencing to match the hardware specification.
- Set system PM ops.
- Various stylistic changes and general clean-up.
- Add myself as a maintainer.

Patches in v4 No applies recorded yet

#Subject and filesSizeRepliesApplied
1/4dt-bindings: Add a vendor prefix for Galaxycore Inc.Documentation/devicetree/bindings/vendor-prefixes.yaml+2 -01 reply
2/4media: dt-bindings: media: i2c: Add bindings for GC5035Documentation/devicetree/bindings/media/i2c/gc5035.yaml+142 -02 replies
3/4media: i2c: Add a driver for the Galaxycore GC5035 sensorMAINTAINERS drivers/media/i2c/Kconfig drivers/media/i2c/Makefile +1 more+1515 -00 replies
4/4media: i2c: gc5035: Add OTP configuration handlingdrivers/media/i2c/gc5035.c+478 -01 reply

Reviews trailers per patch

1 of 4 patches has a Reviewed-by or Acked-by.

PatchRob Herring
1/4A-b
2/4
3/4
4/4

Trailers given in replies are filled; those carried in the patches from earlier versions are outlined with dashes.

Read the v4 thread

Cover letter [PATCH v4 0/4] Galaxycore GC5035 sensor driver

Hi everyone,

This series adds YAML DT binding and V4L2 sub-device driver for Galaxycore GC5035 5-megapixel 10-bit Bayer CMOS 1/4" sensor, which has a two-lane MIPI CSI-2 data interface and uses the I2C bus for control

The initial version supports the following features:
- Manual exposure, analog and digital gain control
- Vertical blanking interval control
- Test pattern generator (color bars)
- Media controller support
- Runtime PM support
- Support operating modes:
o 2592x1944 at 30fps,
o 1296x972 at 30fps,
o 1280x720 at 60fps.

A separate patch in the series adds support for loading manufacture-time configuration from the sensor OTP, which currently includes:
- register patch table,
- DPC table.

This is based on Hao He's and Xingyu Wu's v3 series that partially reached the maling lists:
- patch 1/3 - equivalent of patch 1/4 of this seres:
https://patchwork.ozlabs.org/project/devicetree-bindings/patch/[email protected]/
- patch 3/3 - equivalent of patches 3/4 + 4/4 of this series:
https://patchwork.ozlabs.org/project/devicetree-bindings/patch/[email protected]/
Patch 2/3 that adds DT bindings was missing so I recreated it from scratch on my own.

Changes from v3:
- Require and handle clock-frequency and link-frequencies device properties.
- Separate the driver patch into one for base functionality and another for OTP handling.
- Do not perform OTP initialization on driver probe, since it's a costly operation. Instead do it at first streaming time.
- Fix power sequencing to match the hardware specification.
- Set system PM ops.
- Various stylistic changes and general clean-up.
- Add myself as a maintainer.

Hao He (3):
dt-bindings: Add a vendor prefix for Galaxycore Inc.
media: i2c: Add a driver for the Galaxycore GC5035 sensor
media: i2c: gc5035: Add OTP configuration handling

Tomasz Figa (1):
media: dt-bindings: media: i2c: Add bindings for GC5035

 .../devicetree/bindings/media/i2c/gc5035.yaml |  142 ++
 .../devicetree/bindings/vendor-prefixes.yaml  |    2 +
 MAINTAINERS                                   |    7 +
 drivers/media/i2c/Kconfig                     |   13 +
 drivers/media/i2c/Makefile                    |    1 +
 drivers/media/i2c/gc5035.c                    | 1972 +++++++++++++++++
 6 files changed, 2137 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/media/i2c/gc5035.yaml
 create mode 100644 drivers/media/i2c/gc5035.c
Signature · 1 line
2.28.0.402.g5ffc5be6b7-goog