sunxi: enable automatic eMMC boot partition support
Get series with b4
b4 am [email protected]Versions newest first
- v1 Latest5 patches 0 repliesNew
Patches in v1 No applies recorded yet
| # | Subject and files | Size | Replies | Applied |
|---|---|---|---|---|
| 1/5 | sunxi: Fix is_boot0_magic macroarch/ | +1 | 0 replies | |
| 2/5 | spl: mmc: extend spl_mmc_boot_mode() to take mmc argumentarch/ arch/ arch/ +10 more | +15 | 3 replies | |
| 3/5 | sunxi: Simplify eMMC boot partition bootingarch/ | +9 | 0 replies | |
| 4/5 | sunxi: eMMC: Add automatic boot detectionarch/ | +85 | 0 replies | |
| 5/5 | sunxi: defconfig: enable eMMC boot partition supportconfigs/ configs/ configs/ +1 more | +4 | 0 replies |
Reviews trailers per patch
1 of 5 patches has a Reviewed-by or Acked-by.
| Patch | Stefano Babic | Ley Foon Tan | Lokesh Vutla |
|---|---|---|---|
| 1/5 | |||
| 2/5 | R-b | R-b | A-b |
| 3/5 | |||
| 4/5 | |||
| 5/5 |
Trailers given in replies are filled; those carried in the patches from earlier versions are outlined with dashes. Scroll the table sideways for all 3 reviewers.
Cover letter [PATCH 0/5] sunxi: enable automatic eMMC boot partition support
The eMMC standard describes the concept of boot partitions, consisting of two storage areas separate from the main user data partition. The Allwinner BootROM supports loading SPL/Boot0 from such a boot partition, if that is configured in the eMMC device [1].
To load U-Boot proper along with the SPL from there, currently this requires to enable CONFIG_SUPPORT_EMMC_BOOT, and this means that this build won't boot from the normal eMMC user partition anymore. Also the raw MMC sector offset needs to be adjusted manually, preventing a boot from an SD card.
This series introduces automatic detection of eMMC boot partition boot. Patch 3/5 automates the raw MMC sector offset decision, allowing such a build to also boot from an SD card.
Unfortunately the BootROM does not mark an eMMC boot partition boot differently from the normal eMMC user data partition boot, so patch 4/5 introduces a function that repeats the BootROM algorithm, so that the SPL comes to the same conclusion as the BootROM. This allows to build one single image that boots from everywhere: eMMC user data, eMMC boot, SD card, SPI flash.
Patch 1/5 contains a bugfix that's needed in a later patch, patch 2/5 extends the generic spl_mmc_boot_mode() interface to make 4/5 feasible.
Without enabling CONFIG_SUPPORT_EMMC_BOOT, the AArch64 SPL grows by 92 bytes, ARMv7 grows by 36 bytes. With enabling the feature, the size goes up by 444 bytes (AArch64) and 260 bytes (ARMv7).
Even for AArch64 this is still 4.5 KB below the SPL limit, so patch 5/5 enables this new mechanism for some boards I could test this on.
Please have a look and test this if you have a board with eMMC. I put installation instructions into the linux-sunxi Wiki:
http://linux-sunxi.org/Bootable_eMMC
Cheers,
Andre
[1] http://linux-sunxi.org/Bootable_eMMC#The_BROM_implementation_details
Andre Przywara (5):
sunxi: Fix is_boot0_magic macro
spl: mmc: extend spl_mmc_boot_mode() to take mmc argument
sunxi: Simplify eMMC boot partition booting
sunxi: eMMC: Add automatic boot detection
sunxi: defconfig: enable eMMC boot partition support
arch/arm/include/asm/arch-sunxi/spl.h | 2 +- arch/arm/mach-imx/spl.c | 2 +- arch/arm/mach-k3/am6_init.c | 2 +- arch/arm/mach-k3/j721e_init.c | 2 +- arch/arm/mach-omap2/boot-common.c | 2 +- arch/arm/mach-rockchip/spl.c | 2 +- arch/arm/mach-socfpga/spl_a10.c | 2 +- arch/arm/mach-socfpga/spl_agilex.c | 2 +- arch/arm/mach-socfpga/spl_gen5.c | 2 +- arch/arm/mach-socfpga/spl_s10.c | 2 +- arch/arm/mach-stm32mp/spl.c | 2 +- arch/arm/mach-sunxi/board.c | 94 +++++++++++++++++++++- arch/arm/mach-uniphier/mmc-boot-mode.c | 5 +- common/spl/spl_mmc.c | 4 +- configs/bananapi_m64_defconfig | 1 + configs/emlid_neutis_n5_devboard_defconfig | 1 + configs/pine64-lts_defconfig | 1 + configs/pine_h64_defconfig | 1 + include/spl.h | 3 +- 19 files changed, 113 insertions(+), 19 deletions(-)
Signature · 1 line
2.17.5