Skip to content

sunxi: enable automatic eMMC boot partition support

Tom Rini u-boot 1 version New

Get series with b4
b4 am 20201110123839.GZ5340@bill-the-cat

Versions newest first

  1. v1 Latest0 of 5 patches 0 repliesNew

Patches in v1 No applies recorded yet

None of the 5 patches the cover letter announces are in this archive.

Reviews trailers per patch

No Reviewed-by, Acked-by or Tested-by trailers for v1 yet.

Read the v1 thread

Cover letter [PATCH 0/5] sunxi: enable automatic eMMC boot partition support
Quoted 56 lines · Andr? Przywara

On 10/11/2020 12:38, Tom Rini wrote:

Hi Tom,

Quoted 52 lines · Andr? Przywara
Quoted 51 lines · Peter Robinson

Hi,

Quoted 31 lines · Andre Przywara
Quoted 30 lines

The eMMC standard describes the concept of boot partitions, consisting of two storage areas separate from the main user data partition. The Allwinner BootROM supports loading SPL/Boot0 from such a boot partition, if that is configured in the eMMC device [1].

To load U-Boot proper along with the SPL from there, currently this requires to enable CONFIG_SUPPORT_EMMC_BOOT, and this means that this build won't boot from the normal eMMC user partition anymore. Also the raw MMC sector offset needs to be adjusted manually, preventing a boot from an SD card.

This series introduces automatic detection of eMMC boot partition boot. Patch 3/5 automates the raw MMC sector offset decision, allowing such a build to also boot from an SD card.
Unfortunately the BootROM does not mark an eMMC boot partition boot differently from the normal eMMC user data partition boot, so patch 4/5 introduces a function that repeats the BootROM algorithm, so that the SPL comes to the same conclusion as the BootROM. This allows to build one single image that boots from everywhere: eMMC user data, eMMC boot, SD card, SPI flash.
Patch 1/5 contains a bugfix that's needed in a later patch, patch 2/5 extends the generic spl_mmc_boot_mode() interface to make 4/5 feasible.

Without enabling CONFIG_SUPPORT_EMMC_BOOT, the AArch64 SPL grows by 92 bytes, ARMv7 grows by 36 bytes. With enabling the feature, the size goes up by 444 bytes (AArch64) and 260 bytes (ARMv7).
Even for AArch64 this is still 4.5 KB below the SPL limit, so patch 5/5 enables this new mechanism for some boards I could test this on.

Quoted 6 lines
Quoted 3 lines

Please have a look and test this if you have a board with eMMC. I put installation instructions into the linux-sunxi Wiki:
http://linux-sunxi.org/Bootable_eMMC

It would probably be good to put that link in the local Allwinner docs so it's easier for people to find.

Yeah, actually as you mention it:
There does not seem to be some generic README.sunxi file where this would belong to.

Jagan: would it make sense to create one, and describe how to get U-Boot into the devices (SD card, eMMC, SPI flash, FEL)? That could move some parts of README.sunxi64 out of there, since they apply to all Allwinner devices.

Quoted 8 lines
Quoted 4 lines
Quoted 2 lines

If people agree that this is the right thing to do, I would be happy to send a patch.

Well, rST file in doc/boards/ and all of that, but, yes please.

Ah, thanks for the pointer, looks good.
Do we accept symlinks in the tree? There are quite some references to board/sunxi/README.sunxi64 out there. Or shall I keep a stub instead?

As there's external references to the README file, yes, please stub it out pointing people to the new rST file. Thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 659 bytes
Desc: not available
URL: <https://lists.denx.de/pipermail/u-boot/attachments/20201110/2eb60f59/attachment.sig>