Skip to content

RFC vfio/pci: Enable runtime power management support

Abhishek Sahu kvm lkml oe-kbuild-all 2 versions – In review

Get series with b4
b4 am [email protected]

Versions newest first · linked by author and title

  1. v2 RFC Latest5 patches 14 repliesIn review
  2. v1 RFC3 patches 9 repliesSuperseded

Patches in v2 No applies recorded yet

#Subject and filesSizeRepliesApplied
1/5vfio/pci: register vfio-pci driver with runtime PM frameworkdrivers/vfio/pci/vfio_pci.c drivers/vfio/pci/vfio_pci_core.c include/linux/vfio_pci_core.h+75 -272 replies
2/5vfio/pci: virtualize PME related registers bits and initialize to zerodrivers/vfio/pci/vfio_pci_config.c+32 -10 replies
3/5vfio/pci: fix memory leak during D3hot to D0 tranistiondrivers/vfio/pci/vfio_pci_core.c include/linux/vfio_pci_core.h+51 -33 replies
4/5vfio/pci: Invalidate mmaps and block the access in D3hot power statedrivers/vfio/pci/vfio_pci_core.c drivers/vfio/pci/vfio_pci_rdwr.c+51 -162 replies
5/5vfio/pci: add the support for PCI D3cold statedrivers/vfio/pci/vfio_pci.c drivers/vfio/pci/vfio_pci_config.c drivers/vfio/pci/vfio_pci_core.c +2 more+211 -97 replies

Reviews trailers per patch

No Reviewed-by, Acked-by or Tested-by trailers for v2 yet.

Read the v2 thread

Cover letter [RFC PATCH v2 0/5] vfio/pci: Enable runtime power management support

Currently, there is very limited power management support available in the upstream vfio-pci driver. If there is no user of vfio-pci device, then it will be moved into D3Hot state. Similarly, if we enable the runtime power management for vfio-pci device in the guest OS, then the device is being runtime suspended (for linux guest OS) and the PCI device will be put into D3hot state (in function vfio_pm_config_write()). If the D3cold state can be used instead of D3hot, then it will help in saving maximum power. The D3cold state can't be possible with native PCI PM. It requires interaction with platform firmware which is system-specific. To go into low power states (including D3cold), the runtime PM framework can be used which internally interacts with PCI and platform firmware and puts the device into the lowest possible D-States. This patch series registers the vfio-pci driver with runtime PM framework and uses the same for moving the physical PCI device to go into the low power state.

The current PM support was added with commit 6eb7018705de ("vfio-pci:
Move idle devices to D3hot power state") where the following point was mentioned regarding D3cold state.

"It's tempting to try to use D3cold, but we have no reason to inhibit
hotplug of idle devices and we might get into a loop of having the device disappear before we have a chance to try to use it."

With the runtime PM, if the user want to prevent going into D3cold then /sys/bus/pci/devices/.../d3cold_allowed can be set to 0 for the devices where the above functionality is required instead of disallowing the D3cold state for all the cases.

Since D3cold state can't be achieved by writing PCI standard PM config registers, so a new IOCTL has been added, which change the PCI device from D3hot to D3cold state and then D3cold to D0 state. The hypervisors can implement virtual ACPI methods. For example, in guest linux OS if PCI device ACPI node has _PR3 and _PR0 power resources with _ON/_OFF method, then guest linux OS makes the _OFF call during D3cold transition and then _ON during D0 transition. The hypervisor can tap these virtual ACPI calls and then do the D3cold related IOCTL in vfio driver.

The BAR access needs to be disabled if device is in D3hot state. Also, there should not be any config access if device is in D3cold state. This patch series added this support also.

Also, during testing one use case has been identified where the memory taken for PCI state saving is not getting freed. So fixed that also.

* Changes in v2

- Rebased patches on v5.17-rc1.
- Included the patch to handle BAR access in D3cold.
- Included the patch to fix memory leak.
- Made a separate IOCTL that can be used to change the power state from D3hot to D3cold and D3cold to D0.
- Addressed the review comments given in v1.

Abhishek Sahu (5):
vfio/pci: register vfio-pci driver with runtime PM framework vfio/pci: virtualize PME related registers bits and initialize to zero vfio/pci: fix memory leak during D3hot to D0 tranistion vfio/pci: Invalidate mmaps and block the access in D3hot power state vfio/pci: add the support for PCI D3cold state

 drivers/vfio/pci/vfio_pci.c        |   4 +-
 drivers/vfio/pci/vfio_pci_config.c |  44 +++-
 drivers/vfio/pci/vfio_pci_core.c   | 363 ++++++++++++++++++++++++++---
 drivers/vfio/pci/vfio_pci_rdwr.c   |  20 +-
 include/linux/vfio_pci_core.h      |   6 +
 include/uapi/linux/vfio.h          |  21 ++
 6 files changed, 411 insertions(+), 47 deletions(-)
Signature · 1 line
2.17.1