Skip to content

arm64: dts: verdin-imx8mp: usb dual-role switching et. al.

Marcel Ziswiler linux-arm-kernel linux-devicetree lkml 1 version Applied

Status from this message: Applied all, thanks!

Get series with b4
b4 am [email protected]

Versions newest first

  1. v1 Latest6 patches 1 replyApplied

Patches in v1 Applied

#Subject and filesSizeRepliesApplied
1/6arm64: dts: verdin-imx8mp: improve pinctrl for vbus-suppliesarch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi+2 -20 replies
2/6arm64: dts: verdin-imx8mp: remove usb_2 over-current detection disablingarch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi+0 -10 replies
3/6arm64: dts: verdin-imx8mp: add usb_1 over-current detectionarch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi+12 -20 replies
4/6arm64: dts: verdin-imx8mp: disable usb port power controlarch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi+5 -00 replies
5/6arm64: dts: verdin-imx8mp: add gpio usb-b connectorarch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi+14 -60 replies
6/6arm64: dts: verdin-imx8mp: dahlia: mark usb_2 permanently attachedarch/arm64/boot/dts/freescale/imx8mp-verdin-dahlia.dtsi+1 -00 replies

Reviews trailers per patch

No Reviewed-by, Acked-by or Tested-by trailers for v1 yet.

Read the v1 thread

Cover letter [PATCH v1 0/6] arm64: dts: verdin-imx8mp: usb dual-role switching et. al.

From: Marcel Ziswiler <[email protected]>

This series is an assortment of USB dual-role specific commits as follows:

Improvement of pinctrl for vbus-supplies:
As we are using two fixed regulators for Verdin USB_1_EN (SODIMM 155) and Verdin USB_2_EN (SODIMM 185), those should be muxed as GPIOs rather than OTG_PWR.

Removal of USB_2 over-current detection disabling:
The disable-over-current property is only applicable for the ci-hdrc-usb2 and dwc2 drivers while the i.MX 8M Plus integrates dwc3 IP. Therefore remove this property which does not really serve any purpose here.

Addition of USB_1 over-current detection:
Add Verdin USB_1 over-current detection functionality via Verdin USB_1_OC# (SODIMM 157) being active-low and removing its previous gpio_hog3 mapping.

Disabling of USB port power controls:
Disable port power control on Verdin USB_1/2 as we use regular fixed-regulators with Verdin USB_1/2_EN as enable GPIOs.

Addition of GPIO USB-B connector:
Add GPIO USB-B connector (gpio-usb-b-connector) functionality using Verdin USB_1_ID.

Marking USB_2 as permanently attached:
As both Dahlia and the Verdin Development Board have on-carrier permanently attached USB hubs mark Verdin USB_2 as such.

Note:
Currently, I am still seeing a rare race condition of sorts when booting the system with Verdin USB_1 as a host port with a USB memory stick plugged in. This exact patch series applied on top of NXP's latest downstream 5.15.52_2.1.0 release (together with backporting a few more dwc3-specific patches) actually makes this same use case work very reliably. However, NXP also keeps further downstream-only patches which I plan to further investigate and hopefully upstream a proper fix for soon.

Marcel Ziswiler (6):
arm64: dts: verdin-imx8mp: improve pinctrl for vbus-supplies
arm64: dts: verdin-imx8mp: remove usb_2 over-current detection
disabling
arm64: dts: verdin-imx8mp: add usb_1 over-current detection
arm64: dts: verdin-imx8mp: disable usb port power control
arm64: dts: verdin-imx8mp: add gpio usb-b connector
arm64: dts: verdin-imx8mp: dahlia: mark usb_2 permanently attached

 .../dts/freescale/imx8mp-verdin-dahlia.dtsi   |  1 +
 .../boot/dts/freescale/imx8mp-verdin.dtsi     | 40 ++++++++++++++-----
 2 files changed, 32 insertions(+), 9 deletions(-)
Signature · 7 lines
2.36.1


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel