Skip to content

Add JH7110 cpufreq support

Mason Huo linux-devicetree linux-pm linux-riscv lkml 4 versions – Applied

Status from this message: I applied the two dts patches yesterday, you shouldn't need to do

Get series with b4
b4 am [email protected]

Versions newest first · linked by author and title

  1. v4 Latest3 patches 9 repliesApplied
  2. v33 patches 5 repliesApplied
  3. v23 patches 2 repliesSuperseded
Earlier versions · 1
VersionPostedPatchesRepliesStatus
v13 patches10 repliesSuperseded

Changes in v4 from the cover letter

- Fix the dtb_check issues for axp15060 pmic dts configuration.

Patches in v4 Applied

#Subject and filesSizeRepliesApplied
1/3riscv: dts: starfive: Enable axp15060 pmic for cpufreqarch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi+17 -02 replies
2/3cpufreq: dt-platdev: Add JH7110 SOC to the allowlistdrivers/cpufreq/cpufreq-dt-platdev.c+2 -06 replies
3/3riscv: dts: starfive: Add cpu scaling for JH7110 SoCarch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi arch/riscv/boot/dts/starfive/jh7110.dtsi+49 -00 replies

Reviews trailers per patch

No Reviewed-by, Acked-by or Tested-by trailers for v4 yet.

Read the v4 thread

Cover letter [PATCH v4 0/3] Add JH7110 cpufreq support

The StarFive JH7110 SoC has four RISC-V cores,
and it supports up to 4 cpu frequency loads.

This patchset adds the compatible strings into the allowlist for supporting the generic cpufreq driver on JH7110 SoC. Also, it enables the axp15060 pmic for the cpu power source.

The series has been tested on the VisionFive 2 boards which are equipped with JH7110 SoC and axp15060 pmic.

---
This patchset is based on v6.4-rc4 with these patches applied:
[1] ("regulator: Add X-Powers AXP15060/AXP313a PMIC support")

    https://lore.kernel.org/lkml/[email protected]/

Changes since v3:
- Fix the dtb_check issues for axp15060 pmic dts configuration.

Changes since v2:
- Fix the new blank line at EOF issue in dtsi.

Changes since v1:
- Fix dts node naming issues.
- Move clock properties of cpu node from <board>.dtsi to <soc>.dtsi.
- Follow the alphabetical order to place the cpufreq dt allowlist.

Mason Huo (3):
riscv: dts: starfive: Enable axp15060 pmic for cpufreq
cpufreq: dt-platdev: Add JH7110 SOC to the allowlist
riscv: dts: starfive: Add cpu scaling for JH7110 SoC

 .../jh7110-starfive-visionfive-2.dtsi         | 33 +++++++++++++++++++
 arch/riscv/boot/dts/starfive/jh7110.dtsi      | 33 +++++++++++++++++++
 drivers/cpufreq/cpufreq-dt-platdev.c          |  2 ++
 3 files changed, 68 insertions(+)
Signature · 7 lines
2.39.2


_______________________________________________
linux-riscv mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-riscv