Facilitate new atmel raw nand driver for SAMA5D2
Get series with b4
b4 am [email protected]Versions newest first
- v1 Latest4 patches 4 repliesIn review
Patches in v1 No applies recorded yet
| # | Subject and files | Size | Replies | Applied |
|---|---|---|---|---|
| 1/4 | ARM: dts: at91: sama5d2: Move sfr nodearch/ | +5 | 0 replies | |
| 2/4 | ARM: dts: at91: sama5d2: Port ebi/nand nodes from linuxarch/ | +56 | 0 replies | |
| 3/4 | ARM: dts: at91: sama5d2: Align more node names with Linuxarch/ | +4 | 0 replies | |
| 4/4 | mtd: nand: raw: atmel: Remove duplicate definitionsdrivers/ | +0 | 3 replies |
Reviews trailers per patch
No Reviewed-by, Acked-by or Tested-by trailers for v1 yet.
Cover letter [PATCH 0/4] Facilitate new atmel raw nand driver for SAMA5D2
Hei hei,
for some downstream boards with SAMA5D27 SiP SoCs with raw NAND flash I added the necessary nodes to sama5d2.dtsi with just one little
guesswork: the clocks. Motivation was to fix reading from raw nand flash which failed on some of those boards, while others worked fine. So I suppose the timings for the external interface were set to too slow values. (IIRC I took them from the sama5d2_ptc_ek_nandflash board code back in 2019.)
The solution was basically to switch from the old non-DM driver with hardcoded timings for the external memory interface to the new DM based driver introduced earlier this year, which sets the timings based on ONFI parameters read from the flash chip.
Works for me, but I have no boards with that SoC _and_ a raw NAND flash at hand, which are supported by upstream U-Boot. The only matching upstream config is sama5d2_ptc_ek_nandflash_defconfig but because we don't have that board, I did not touch it.
(When that driver was added with 6a8dfd57220d ("nand: atmel: Add DM based NAND driver") the author claims in the commit message it was tested on SAMA5D3, but none of the sama5d3 configs actually uses it.)
Some more changes to the board dts are necessary, but porting from Linux is straightforward. The necessary changes to the defconfig should look like this:
# CONFIG_I2C is not set
CONFIG_LED=y
CONFIG_LED_GPIO=y
+CONFIG_ATMEL_EBI=y
+CONFIG_MFD_ATMEL_SMC=y
# CONFIG_MMC is not set
CONFIG_MTD=y
-CONFIG_NAND_ATMEL=y
-CONFIG_ATMEL_NAND_HW_PMECC=y
-CONFIG_PMECC_CAP=8
+CONFIG_DM_MTD=y
+CONFIG_DM_NAND_ATMEL=y
CONFIG_SYS_NAND_ONFI_DETECTION=y
CONFIG_PHY_SMSC=y
CONFIG_MACB=y
Hope the changes are acceptable nevertheless. The last patch has a trivial fix for the new atmel raw nand driver which I came up with while working on this.
Greets
Alex
Alexander Dahl (4):
ARM: dts: at91: sama5d2: Move sfr node
ARM: dts: at91: sama5d2: Port ebi/nand nodes from linux
ARM: dts: at91: sama5d2: Align more node names with Linux
mtd: nand: raw: atmel: Remove duplicate definitions
arch/arm/dts/sama5d2.dtsi | 74 ++++++++++++++++++++++++++---- drivers/mtd/nand/raw/atmel/pmecc.c | 3 -- 2 files changed, 65 insertions(+), 12 deletions(-)
base-commit: 2f0282922b2c458eea7f85c500a948a587437b63
Signature · 1 line
2.39.2