cadence-qspi: Add DTR support including PHY mode calibration
Get series with b4
b4 am [email protected]Versions newest first
- v1 Latest11 patches 0 repliesNew
Patches in v1 No applies recorded yet
| # | Subject and files | Size | Replies | Applied |
|---|---|---|---|---|
| 1/11 | mtd: spi-nor: Add calibration hook for high speed SPIdoc/ drivers/ drivers/ +3 more | +234 | 0 replies | |
| 2/11 | mtd: spi-nor: Octal DTR support for IS25*xdrivers/ drivers/ include/ | +89 | 0 replies | |
| 3/11 | spi: cadence-quadspi: Enable DDR bit for DTR commandsdrivers/ drivers/ | +5 | 0 replies | |
| 4/11 | spi: cadence-quadspi: enable opcode extension based on command lengthdrivers/ | +49 | 0 replies | |
| 5/11 | spi: cadence-quadspi: disable automatic write enabledrivers/ drivers/ | +2 | 0 replies | |
| 6/11 | spi: cadence-quadspi: unconditionally disable auto status register readsdrivers/ | +24 | 0 replies | |
| 7/11 | spi: cadence-quadspi: Remove redundant DTR statedrivers/ drivers/ drivers/ | +14 | 0 replies | |
| 8/11 | spi: cadence-quadspi: Direct mode does not support zero length addressesdrivers/ | +2 | 0 replies | |
| 9/11 | spi: cadence-quadspi: Add support for memory DMA channel transfersdrivers/ drivers/ drivers/ | +164 | 0 replies | |
| 10/11 | spi: cadence-quadspi: Add DT control of max Read Delay Capture valuedoc/ drivers/ drivers/ | +12 | 0 replies | |
| 11/11 | spi: cadence-quadspi: Implement high speed calibrationdoc/ drivers/ drivers/ +1 more | +641 | 0 replies |
Reviews trailers per patch
No Reviewed-by, Acked-by or Tested-by trailers for v1 yet.
Cover letter [PATCH 00/11] cadence-qspi: Add DTR support including PHY mode calibration
This series introduces support for DTR mode for the Cadence QSPI/OSPI IP. We have been developing it against the SC594/SC598 from ADI, so there are some limitations specific to our hardware's capabilities. Ideally this series could be enhanced with features introduced in a patch series submitted by AMD, but currently no work has been done to reconcile the two. So this is somewhere between an RFC patch and a patch series we wish to submit as-is for inclusion.
Beyond the specific support for the QSPI peripheral, this series also introduces a more general calibration framework as part of the spi system in order to facilitate integration of calibration support for other controllers within a consistent approach.
Ian Roberts (11):
mtd: spi-nor: Add calibration hook for high speed SPI
mtd: spi-nor: Octal DTR support for IS25*x
spi: cadence-quadspi: Enable DDR bit for DTR commands
spi: cadence-quadspi: enable opcode extension based on command length
spi: cadence-quadspi: disable automatic write enable
spi: cadence-quadspi: unconditionally disable auto status register
reads
spi: cadence-quadspi: Remove redundant DTR state
spi: cadence-quadspi: Direct mode does not support zero length
addresses
spi: cadence-quadspi: Add support for memory DMA channel transfers
spi: cadence-quadspi: Add DT control of max Read Delay Capture value
spi: cadence-quadspi: Implement high speed calibration
doc/device-tree-bindings/spi/spi-bus.txt | 4 + doc/device-tree-bindings/spi/spi-cadence.txt | 11 + drivers/mtd/spi/Kconfig | 12 + drivers/mtd/spi/spi-nor-core.c | 246 ++++++++ drivers/mtd/spi/spi-nor-ids.c | 6 +- drivers/spi/cadence_qspi.c | 444 ++++++++++---- drivers/spi/cadence_qspi.h | 105 +++- drivers/spi/cadence_qspi_apb.c | 572 +++++++++++++++---- drivers/spi/spi-mem.c | 24 + include/linux/mtd/spi-nor.h | 13 + include/spi-mem.h | 19 + 11 files changed, 1226 insertions(+), 230 deletions(-)
Signature · 1 line
2.43.2