media: mt9m114: Changes to make it work with atomisp devices
Get series with b4
b4 am [email protected]Versions newest first · linked by author and title
- v3 Latest15 patches 15 repliesIn review
- v212 patches 19 repliesSuperseded
Changes in v3 from the cover letter
- Document that using 768Mhz for out_clock_max does not work
- Improve "media: mt9m114: Put sensor in reset on power down" commit message
- Drop setting of the MT9M114_CAM_OUTPUT_FORMAT_BT656_CROP_SCALE_DISABLE bit
- Split "media: mt9m114: Fix scaler bypass mode" into multiple patches, addressing various review comments as part of this
Patches in v3 No applies recorded yet
Reviews trailers per patch
12 of 15 patches have a Reviewed-by or Acked-by.
| Patch | Laurent Pinchart |
|---|---|
| 1/15 | R-b |
| 2/15 | |
| 3/15 | |
| 4/15 | R-b |
| 5/15 | R-b |
| 6/15 | R-b |
| 7/15 | R-b |
| 8/15 | R-b |
| 9/15 | R-b |
| 10/15 | R-b |
| 11/15 | R-b |
| 12/15 | R-b |
| 13/15 | |
| 14/15 | R-b |
| 15/15 | R-b |
Trailers given in replies are filled; those carried in the patches from earlier versions are outlined with dashes.
Cover letter [PATCH v3 00/15] media: mt9m114: Changes to make it work with atomisp devices
Hi All,
Here is v3 of my series to make the "mainline" mt9m114 driver work on devices with an atomisp CSI2 receiver / ISP. This has been tested on an Asus T100TA.
Changes in v3:
- Document that using 768Mhz for out_clock_max does not work
- Improve "media: mt9m114: Put sensor in reset on power down" commit message
- Drop setting of the MT9M114_CAM_OUTPUT_FORMAT_BT656_CROP_SCALE_DISABLE bit
- Split "media: mt9m114: Fix scaler bypass mode" into multiple patches, addressing various review comments as part of this
Changes in v2:
- Rebase on top of sailus/media_tree.git/fixes which now has 4 of the patches from Mathis': "MT9M114 driver bugfix and improvements" series, this avoids most of the conlicts between the 2 series
- Add Laurent's Reviewed-by to some of the patches
- Add select VIDEO_APTINA_PLL to Kconfig
- Use correct aptina_pll_limits
- After setting reset high wait 20 clk cycles before disabling the clk and regulators
- When bypassing the scalar make ifp_get_selection() / ifp_set_selection() fill sel->r with a rectangle of (0,0)/wxh and return 0 instead of returning -EINVAL
Regards,
Hans
Hans de Goede (15):
media: aptina-pll: Debug log p1 min and max values
media: mt9m114: Add support for clock-frequency property
media: mt9m114: Use aptina-PLL helper to get PLL values
media: mt9m114: Lower minimum vblank value
media: mt9m114: Fix default hblank and vblank values
media: mt9m114: Tweak default hblank and vblank for more accurate fps
media: mt9m114: Avoid a reset low spike during probe()
media: mt9m114: Put sensor in reset on power down
media: mt9m114: Add and use mt9m114_ifp_get_border() helper function
media: mt9m114: Adjust IFP selections and src format when src pixelfmt
changes to/from RAW10
media: mt9m114: Update src pad sel and format when sink pad format
changes
media: mt9m114: Don't allow changing the IFP crop/compose selections
when bypassing the scaler
media: mt9m114: Drop start-, stop-streaming sequence from initialize
media: mt9m114: Return -EPROBE_DEFER if no endpoint is found
media: mt9m114: Add ACPI enumeration support
drivers/media/i2c/Kconfig | 1 + drivers/media/i2c/aptina-pll.c | 2 + drivers/media/i2c/mt9m114.c | 255 +++++++++++++++++++++++++-------- 3 files changed, 196 insertions(+), 62 deletions(-)
Signature · 1 line
2.49.0