iio: mcp9600: Features and improvements
Get series with b4
b4 am [email protected]Versions newest first · linked by author and title
- v5 Latest posting 2/20 of 5 patches 3 repliesIn review
- v5 posting 1/25 patches 17 repliesSuperseded
Changes in v5 from the cover letter
- Missed a one line fix to IIR patch (5/5)
Patches in v5 posting 2/2 No applies recorded yet
None of the 5 patches the cover letter announces are in this archive.
Reviews trailers per patch
| Patch | Krzysztof Kozlowski | David Lechner |
|---|---|---|
| Series | R-b | R-b R-b R-b R-b |
Trailers given in replies are filled; those carried in the patches from earlier versions are outlined with dashes.
Cover letter [PATCH v5 0/5] iio: mcp9600: Features and improvements
From: Ben Collins <[email protected]>
ChangeLog:
v5 -> v6:
- Fix accidental typo added in dt-bindings: IRQ_TYPE_EDGE_RISIN
- Correct some constraints in dt-bindings
- Reverse if/then for mcp9601 vs mcp9600 constraints in dt-bindings
- Updates to changelog for patch 2/6 (dt-bindings mcp9600)
- Cleanup tabs that were converted to spaces
- Split thermocouple-type default to separate patch
v4 -> v5:
- Missed a one line fix to IIR patch (5/5)
v3 -> v4:
- Based on feedback from David Lechner <[email protected]>
* Allow fallback compatible in dt-bindings for mcp9601.
- Based on feedback from Jonathan Cameron <[email protected]>
* Be explicit in patch description for fixed width changes.
* Check chip_info for NULL to quiet warnings from kernel-test-robot
* Remove "and similar" for long description of MCP9600.
- Based on lots of feedback, use frequency values for IIR, and use filter_type[none, ema] to enable or disable.
- Set default 3 for thermocouple in dt-binding
- Rework open/short circuit in dt-bindings
v2 -> v3:
- Improve changelogs in each patch
- Based on feedback from Andy Shevchenko <[email protected]>
* Set register offsets to fixed width
* Fix typos
* Future-proof Kconfig changes
* Convert to using chip_info paradigm
* Verbiage: dt -> firmware description
* Use proper specifiers and drop castings
* Fix register offset to be fixed-width
* u8 for cfg var
* Fix % type for u32 to be %u
* Make blank lines consistent between case statements
* FIELD_PREP -> FIELD_MODIFY
* Remove explicit setting of 0 value in filter_level
- Based on feedback from David Lechner <[email protected]>
* Rework IIR values exposed to sysfs. Using the ratios, there was no way to represent "disabled" (i.e. infinity). Based on the bmp280 driver I went with using the power coefficients (e.g. 1, 2, 4, 8, ...) where 1 is disabled (n=0).
v1 -> v2:
- Break into individual patches
v1:
- Initial patch to enable IIR and thermocouple-type
- Recognize mcp9601
Ben Collins (6):
dt-bindings: iio: mcp9600: Set default 3 for thermocouple-type
dt-bindings: iio: mcp9600: Add microchip,mcp9601 and add constraints
iio: mcp9600: White space and fixed width cleanup
iio: mcp9600: Recognize chip id for mcp9601
iio: mcp9600: Add support for thermocouple-type
iio: mcp9600: Add support for IIR filter
.../iio/temperature/microchip,mcp9600.yaml | 61 +++- drivers/iio/temperature/Kconfig | 8 +- drivers/iio/temperature/mcp9600.c | 295 +++++++++++++++++- 3 files changed, 341 insertions(+), 23 deletions(-)
Signature · 1 line
2.39.5