Skip to content

iio: dac: Add support for MAX22007 DAC

Janani Sunil linux-devicetree linux-doc linux-iio lkml 4 versions – In review

Get series with b4
b4 am [email protected] change-id 20251219-max22007-dev-1aaf08db7890

Versions newest first

  1. v4 Latest2 patches 2 repliesIn review
  2. v32 patches 4 repliesSuperseded inferred link
  3. v22 patches 8 repliesSuperseded
Earlier versions · 1
VersionPostedPatchesRepliesStatus
v13 patches9 repliesSuperseded

Changes in v4 from the cover letter

- Re-sent of improper v3 (at v3 I *accidentaly* reverted the dt-binding commit to v1 after a rebase).
- Corrected description for reset GPIO in the dt-binding
- Wrap commit description at 75 columns
- Link to v3: https://lore.kernel.org/r/[email protected]

Patches in v4 No applies recorded yet

#Subject and filesSizeRepliesApplied
1/2dt-bindings: iio: dac: Add max22007Documentation/devicetree/bindings/iio/dac/adi,max22007.yaml MAINTAINERS+127 -00 replies
2/2iio: dac: Add MAX22007 DAC driver supportMAINTAINERS drivers/iio/dac/Kconfig drivers/iio/dac/Makefile +1 more+503 -01 reply

Reviews trailers per patch

1 of 2 patches has a Reviewed-by or Acked-by.

PatchKrzysztof Kozlowski
1/2R-b
2/2

Trailers given in replies are filled; those carried in the patches from earlier versions are outlined with dashes.

Read the v4 thread

Cover letter [PATCH v4 0/2] iio: dac: Add support for MAX22007 DAC

This patch series introduces support for the Analog Devices MAX22007, a quad-channel, 12-bit digital-to-analog converter (DAC) with integrated precision output amplifiers and configurable voltage/current output capability.

**Device Overview:**
The MAX22007 features four independent DAC channels that can each be configured for either voltage output (0-12.5V) or current output (0-25mA) mode. The device communicates via SPI interface with built-in CRC8 error checking for data integrity.

**Features Implemented:**
- Support for all 4 DAC channels with 12-bit resolution
- Per-channel voltage/current mode configuration via device tree property adi,ch-func = [voltage, current]
- Independent power control for each channel (attribute)
- Hardware reset support via GPIO (during probe)
- CRC8 error checking for SPI communication

**Patch Summary:**
1. dt-bindings: Binding documentation with channel configuration
2. driver: Implement IIO DAC driver

**Testing:**
The driver was hardware tested on a Raspberry Pi4 on top of v6.12.y kernel using the MAX22007EVKIT evaluation board.

Janani Sunil (3):

dt-bindings: iio: dac: Add max22007
iio: dac: Add MAX22007 DAC driver support
---
To: Lars-Peter Clausen <[email protected]>
To: Michael Hennerich <[email protected]>
To: Jonathan Cameron <[email protected]>
To: Rob Herring <[email protected]>
To: Krzysztof Kozlowski <[email protected]>
To: Conor Dooley <[email protected]>
To: Jonathan Corbet <[email protected]>

---
Changes in v4:
- Re-sent of improper v3 (at v3 I *accidentaly* reverted the dt-binding commit to v1 after a rebase).
- Corrected description for reset GPIO in the dt-binding
- Wrap commit description at 75 columns
- Link to v3: https://lore.kernel.org/r/[email protected]

Changes in v3:
- Remove node defined for power supplies in the devicetree documentaiton
- Made use of CRC8_TABLE_SIZE macro in the crc table definition
- Corrected casting of reg address in the SPI read function
- Applied reverse christmas tree variable ordering
- Added a macro fro the reference voltage and reused the same in the
scale factor
- Removed usage of 'supplies' in enabling bulk regulator and removed
unused variable 'i'
- Added step n the probe function to toggle the reset GPIO
- Updated spacing in macro definitions
- Link to v2: https://lore.kernel.org/r/[email protected]/

Changes in v2:
- Wrap commit messages as per coding guidelines
- Removed all driver references from the hardware
- Update property description for reset-gpio
- Removed allOf
- Added minimum/maximum limits for channel number in the devicetree
binding
- Replaced adi,type with adi,ch-func.
- Added reference to required supplies in the binding, configured them
in the driver
- Channels are not a required property anymore.
- Replaced instances of 'channel' in macros to just 'ch'
- Added trailing commas wherever necessary, removed them as per comments
- Add explicit values for enum- max22007_channel_power
- Replace channel spec structure member 'iio_chan' with 'iio_chans'
- Use spi_write_then_read() API in the max22007_spi_read() API
- Check for reg_size ==1 and hardcode the size otherwise
- Wrap lines in the driver to 80 characters
- Update in-line comment on the resolution
- Separate declarations with assignment, from the ones that don't
- Update the usage of channel template
- Add a local device descriptor to point to the SPI device
- Add a transition of the Reset GPIO from low to high in the probe
- Make use of regmap_set_bits() instead of regmap_update_bits during CRC Enable function call.
- Remove the documentation commit, as it is not needed anymore.
- Link to v1: https://lore.kernel.org/r/[email protected]

---
Janani Sunil (2):
dt-bindings: iio: dac: Add max22007
iio: dac: Add MAX22007 DAC driver support

 .../devicetree/bindings/iio/dac/adi,max22007.yaml  | 120 +++++
 MAINTAINERS                                        |   8 +
 drivers/iio/dac/Kconfig                            |  13 +
 drivers/iio/dac/Makefile                           |   1 +
 drivers/iio/dac/max22007.c                         | 488 +++++++++++++++++++++
 5 files changed, 630 insertions(+)

---
base-commit: 8f0b4cce4481fb22653697cced8d0d04027cb1e8
change-id: 20260114-max22007-patch-6b5c48e37457

Best regards,

Signature · 1 line
Janani Sunil <[email protected]>