Skip to content

Add CCI and CAMSS support for Kaanapali

Hangxiang Ma linux-arm-msm linux-devicetree lkml 2 versions – In review

Get series with b4
b4 am [email protected] change-id 20260507-knp-camera-a070d05ec552

Versions newest first

  1. v2 Latest4 patches 3 repliesIn review
  2. v13 patches 7 repliesApplied

Changes in v2 from the cover letter

- Enable the S5KJN5 image sensor on the MTP, connected to CSIPHY2 and controlled over cci0_i2c1
- Link to v1: https://lore.kernel.org/r/[email protected]

Patches in v2 No applies recorded yet

#Subject and filesSizeRepliesApplied
1/4arm64: dts: qcom: kaanapali: Add CAMSS block definitionsarch/arm64/boot/dts/qcom/kaanapali.dtsi+385 -00 replies
2/4arm64: dts: qcom: kaanapali: Add CCI definitionsarch/arm64/boot/dts/qcom/kaanapali.dtsi+282 -00 replies
3/4arm64: dts: qcom: kaanapali: Add camera MCLK pinctrlarch/arm64/boot/dts/qcom/kaanapali.dtsi+56 -00 replies
4/4arm64: dts: qcom: kaanapali-mtp: Add s5kjn5 image sensor on CSIPHY2arch/arm64/boot/dts/qcom/kaanapali-mtp.dts+90 -03 replies

Reviews trailers per patch

All 4 patches have a Reviewed-by or Acked-by.

PatchVladimir ZapolskiyKonrad DybcioAbel Vesa
1/4R-b
2/4R-b
3/4R-b R-b
4/4R-b

Trailers given in replies are filled; those carried in the patches from earlier versions are outlined with dashes. Scroll the table sideways for all 3 reviewers.

Read the v2 thread

Cover letter [PATCH v2 0/4] Add CCI and CAMSS support for Kaanapali

This series adds the camera device tree support for the Qualcomm Kaanapali SoC and enables it on the Kaanapali MTP board, which adds CCI support and enables the S5KJN5 sensor via CSIPHY2.

This series has been tested using the following commands with S5KJN5 sensor.
- media-ctl --reset
- media-ctl -V '"msm_csiphy2":0[fmt:SGBRG10/4096x3072]'
- media-ctl -V '"msm_csid0":0[fmt:SGBRG10/4096x3072]'
- media-ctl -V '"msm_vfe0_rdi0":0[fmt:SGBRG10/4096x3072]'
- media-ctl -l '"msm_csiphy2":1->"msm_csid0":0[1]'
- media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
- yavta --capture=20 -I -n 5 -f SGBRG10P -s 4096x3072 -F /dev/video0

Driver and dt-binding are waiting to be merged:
https://lore.kernel.org/all/[email protected]

---
Changes in v2:
- Enable the S5KJN5 image sensor on the MTP, connected to CSIPHY2 and controlled over cci0_i2c1
- Link to v1: https://lore.kernel.org/r/[email protected]

---
Hangxiang Ma (4):
arm64: dts: qcom: kaanapali: Add CAMSS block definitions
arm64: dts: qcom: kaanapali: Add CCI definitions
arm64: dts: qcom: kaanapali: Add camera MCLK pinctrl
arm64: dts: qcom: kaanapali-mtp: Add s5kjn5 image sensor on CSIPHY2

 arch/arm64/boot/dts/qcom/kaanapali-mtp.dts |  90 ++++
 arch/arm64/boot/dts/qcom/kaanapali.dtsi    | 723 +++++++++++++++++++++++++++++
 2 files changed, 813 insertions(+)

---
base-commit: 03cfefef0119410fc464d0d56e83626cb570b7a8
change-id: 20260507-knp-camera-a070d05ec552

Best regards,

Signature · 1 line
Hangxiang Ma <[email protected]>