net/mana: add device reset support

From: Wei Hu <[email protected]>

Add support for handling hardware service reset events in the MANA driver. When the MANA kernel driver receives a hardware service event, it initiates a device reset and notifies userspace via IBV_EVENT_DEVICE_FATAL. The MANA PMD handles this by performing an automatic teardown and recovery sequence.

The driver uses ethdev recovery events (ERR_RECOVERING, RECOVERY_SUCCESS, RECOVERY_FAILED) to notify upper layers of the reset lifecycle, and a PCI device removal event callback to distinguish hot-remove from service reset.

Changes since v9:
- Fixed fd leak in the secondary RESET_EXIT IPC handler: when the doorbell page was already mapped, the fd from the message was not closed. Moved close(fd) outside the if/else so it runs unconditionally whenever an fd is present.

Changes since v8:
- Fixed reset thread resource leak: previously reset_thread_active was cleared before emitting recovery callbacks, so no join site would reap the thread. Now the flag stays true throughout the thread lifetime. mana_join_reset_thread detects the self-join case (callback calling dev_stop/dev_close from the reset thread) using rte_thread_equal and calls rte_thread_detach instead of join, so thread resources are freed on exit. External callers continue to join normally.
- Fixed lost condvar signal: added a predicate loop around pthread_cond_timedwait that checks dev_state under reset_cond_mutex. If mana_pci_remove_event_cb signals before the reset thread enters the wait, the wakeup is no longer lost. The PCI remove callback sets dev_state to RESET_FAILED under the same mutex before signaling.
- Added a lock/unlock barrier on reset_ops_lock in mana_pci_remove_event_cb to ensure teardown has completed before emitting the INTR_RMV event.
- Fixed mana_reset_exit_delay return type from uint32_t to int to match the negative error codes it stores.
- Removed unnecessary else-after-goto in mana_probe_port.

Changes since v7:
- Moved heavy teardown (dev_stop, IPC to secondaries, dev_close, MR btree free) from mana_reset_enter (EAL interrupt thread) to mana_reset_thread (control thread). The interrupt handler now only sets state, drains in-flight bursts, and spawns the thread. Teardown runs immediately in the control thread before the recovery timer wait, avoiding blocking the interrupt thread on multi-second IPC timeouts and ibverbs calls. Each function now owns its own lock scope with no lock hand-off between threads.
- Simplified burst_state from encoding device state in bits 1+ to a single blocked flag (bit 1). Only one value was ever stored, so the multi-state encoding was misleading. Added MANA_BURST_BLOCKED constant.
- Updated mana.rst to reflect that teardown runs on the control thread, not the interrupt handler.

Changes since v6:
- Rebased onto latest upstream for-main
- Replaced removed RTE_ETH_DEV_TO_PCI macro with RTE_CLASS_TO_BUS_DEVICE (upstream commit 4757b8df04 removed the old bus-specific ethdev convenience macros)

Changes since v5:
- Replaced RCU QSBR with per-queue atomic burst_state using a single-variable CAS design: bit 0 is the in-burst flag, bit 1 is the blocked flag. The data path uses CAS(0→1) to enter burst and fetch_and(~1) to exit. The reset path uses fetch_or to set the blocked bit and polls bit 0 to drain in-flight bursts. This eliminates the two-variable Dekker pattern and the need for sequential consistency (seq_cst) ordering.
- Removed librte_rcu dependency
- Removed __rte_no_thread_safety_analysis annotations (no longer needed after mutex conversion)
- Moved ERR_RECOVERING event emission before acquiring reset_ops_lock and before mana_reset_enter, so upper layers (e.g. netvsc) can switch data path before mana stops queues. Emitting outside the lock avoids deadlock if the callback calls dev_stop or dev_close.
- Replaced MANA_OPS_*_LOCK macros with mana_reset_trylock() helper function and explicit per-operation wrappers
- Removed unused rte_alarm.h and rte_lock_annotations.h includes
- Added RECOVERY_FAILED event when mana_reset_enter fails internally, so the application always receives a terminal event
- Added mana_clear_burst_state() helper to clear per-queue burst_state on failure paths (reset_failed, dev_stop_lock, dev_close_lock) preventing permanent silent packet drop after a failed reset

Changes since v4:
- Fixed stale rte_spinlock_unlock call in mana_intr_handler that was missed during the spinlock-to-mutex conversion, causing a -Wincompatible-pointer-types warning

Changes since v3:
- Converted reset_ops_lock from rte_spinlock_t to pthread_mutex_t with PTHREAD_PROCESS_SHARED, since the lock is held across blocking IB verbs calls and IPC with 5s timeout
- Removed rte_dev_event_callback_unregister retry loop to avoid deadlock when interrupt thread and reset thread contend

Changes since v2:
- Added per-queue burst_state atomic variable with Dekker-like synchronization to block data path during reset without RCU
- Replaced rte_alarm with condvar + control thread for reset exit
- Made reset_thread_active atomic with CAS — flag is set by creator and only cleared by the joiner, not the thread itself
- Fixed second reset crash: removed reset thread join logic from mana_dev_close (inner function) to avoid corrupting dev_state when called from mana_reset_enter
- Made reset_thread_active RTE_ATOMIC(bool) with explicit ordering
- Added retry loop for rte_dev_event_callback_unregister on -EAGAIN
- Initialized condvar/mutex with PTHREAD_PROCESS_SHARED since priv is in hugepage shared memory
- Added re-check of dev_state after lock acquisition in mana_intr_handler to prevent racing with pci_remove_event_cb
- Replaced (void *)0 with NULL in mp.c
- Added lock ownership comment block at mana_reset_enter
- Documented rte_dev_event_monitor_start() requirement
- Added mana.rst documentation and release note

Changes since v1:
- Removed net/netvsc patch from this series
- Simplified reset exit: mana_reset_exit calls mana_reset_exit_delay directly instead of spawning a thread
- Added __rte_no_thread_safety_analysis annotations for clang
- Switched to rte_thread_create_internal_control
- Fixed declaration-after-statement style issues
- Removed unnecessary blank lines and stale comments

Wei Hu (1):
net/mana: add device reset support

 doc/guides/nics/mana.rst               |   40 +
 doc/guides/rel_notes/release_26_07.rst |    8 +
 drivers/net/mana/mana.c                | 1088 ++++++++++++++++++++++--
 drivers/net/mana/mana.h                |   52 +-
 drivers/net/mana/mp.c                  |   92 +-
 drivers/net/mana/mr.c                  |    6 +-
 drivers/net/mana/rx.c                  |   23 +-
 drivers/net/mana/tx.c                  |   44 +-
 8 files changed, 1245 insertions(+), 108 deletions(-)

2.34.1