Skip to content

Add new driver for WCSS secure PIL loading

Varadarajan Narayanan linux-arm-msm linux-devicetree linux-remoteproc lkml 7 versions – In review

Get series with b4
b4 am [email protected] change-id 20260710-rproc-c4f4d0c1f45c

Versions newest first

  1. v14 Latest9 patches 7 repliesIn review
  2. v136 patches 3 repliesSuperseded inferred link
  3. v126 patches 6 repliesSuperseded inferred link
Earlier versions · 4
VersionPostedPatchesRepliesStatus
v116 patches2 repliesSuperseded inferred link
v106 patches9 repliesSuperseded inferred link
v96 patches3 repliesSuperseded inferred link
v86 patches6 repliesSuperseded

Changes in v14 from the cover letter

- Fix dt-bindings-error
- Drop 'driver' from mbox description
- Remove Tested-by from dt-bindings patch
- Address applicable AI review feedback
Use %pe for PTR_ERR
Use the generic PAS context/API consistently
Handle wcss_sec_start() failures
Use proper PAS stop sequence in wcss_sec_stop()
Disable 'q6v5_wcss' in dtsi and enable in board specific dts
- Update constraints for qcom,smem-states in qcom,ipq5018-wcss-sec-pil.yaml
- Link to v13: https://lore.kernel.org/r/[email protected]

Patches in v14 No applies recorded yet

#Subject and filesSizeRepliesApplied
1/9firmware: qcom_scm: ipq5332: add support to pass metadata sizedrivers/firmware/qcom/qcom_scm.c drivers/firmware/qcom/qcom_scm.h+13 -44 replies
2/9dt-bindings: remoteproc: qcom: document hexagon based WCSS secure PILDocumentation/devicetree/bindings/remoteproc/qcom,ipq5018-wcss-sec-pil.yaml+178 -00 replies
3/9remoteproc: qcom: add hexagon based WCSS secure PIL driverdrivers/remoteproc/Kconfig drivers/remoteproc/Makefile drivers/remoteproc/qcom_q6v5_wcss_sec.c +1 more+360 -03 replies
4/9arm64: dts: qcom: ipq5018: add nodes to bring up q6arch/arm64/boot/dts/qcom/ipq5018.dtsi+66 -00 replies
5/9arm64: dts: qcom: ipq5332: add nodes to bring up q6arch/arm64/boot/dts/qcom/ipq5332.dtsi+64 -00 replies
6/9arm64: dts: qcom: ipq9574: add nodes to bring up q6arch/arm64/boot/dts/qcom/ipq9574.dtsi+61 -10 replies
7/9arm64: dts: qcom: ipq5018: Enable q6v5_wcssarch/arm64/boot/dts/qcom/ipq5018-rdp432-c2.dts+4 -00 replies
8/9arm64: dts: qcom: ipq5332: Enable q6v5_wcssarch/arm64/boot/dts/qcom/ipq5332-rdp-common.dtsi+4 -00 replies
9/9arm64: dts: qcom: ipq9574: Enable q6v5_wcssarch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi+4 -00 replies

Reviews trailers per patch

6 of 9 patches have a Reviewed-by or Acked-by.

PatchKonrad DybcioDmitry BaryshkovVignesh ViswanathanKrzysztof KozlowskiMukesh Ojha
1/9R-b R-b T-b R-b
2/9R-b
3/9R-b T-b
4/9R-b R-b T-b
5/9R-b R-b T-b
6/9R-b R-b T-b
7/9
8/9
9/9

Trailers given in replies are filled; those carried in the patches from earlier versions are outlined with dashes. Scroll the table sideways for all 5 reviewers.

Read the v14 thread

Cover letter [PATCH v14 0/9] Add new driver for WCSS secure PIL loading

As discussed in [4] posting this series after dropping IPQ5424 support to remove dependency on Sricharan's tmel-qmp mailbox driver series v4 [1].

Imported from [email protected].

Imported from [email protected] I've resumed Gokul's work as the last submission dates back April 2025.

- Secure PIL is signed, firmware images which only TrustZone (TZ) can authenticate and load. Linux kernel will send a request to TZ to authenticate and load the PIL images.

- When secure PIL support was added to the existing wcss PIL driver earlier in [2], Bjorn suggested not to overload the existing WCSS rproc driver, instead post a new driver for PAS based IPQ WCSS driver. This series adds a new secure PIL driver for the same.

- Also adds changes to scm to pass metadata size as required for IPQ5332, reposted from [3].

[1]
https://patchwork.kernel.org/project/linux-arm-msm/cover/[email protected]/

[2]
https://patchwork.kernel.org/project/linux-arm-msm/patch/[email protected]/

[3]
https://patchwork.kernel.org/project/linux-arm-msm/patch/[email protected]/

[4]
https://lore.kernel.org/linux-arm-msm/aUN7Aer%[email protected]/

Changes in v14:
- Fix dt-bindings-error
- Drop 'driver' from mbox description
- Remove Tested-by from dt-bindings patch
- Address applicable AI review feedback
Use %pe for PTR_ERR
Use the generic PAS context/API consistently
Handle wcss_sec_start() failures
Use proper PAS stop sequence in wcss_sec_stop()
Disable 'q6v5_wcss' in dtsi and enable in board specific dts
- Update constraints for qcom,smem-states in qcom,ipq5018-wcss-sec-pil.yaml
- Link to v13: https://lore.kernel.org/r/[email protected]

Changes in v13:
- Rebase to ToT (First patch alone had conflicts)
- Add 'Tested-by: Vignesh'
- Link to v12: https://lore.kernel.org/linux-arm-msm/[email protected]/

Changes in v12:
- No code change
- Rebase to ToT
- Change quicinc mail ids to oss.qualcomm.com mail ids
- Link to v11: https://lore.kernel.org/linux-arm-msm/[email protected]/

Changes in v11:
- Add R-b tags
- Rebase the first patch ("firmware: qcom_scm: ipq5332: add support to pass metadata size") to top of tree
- No change in other patches
- Link to v10: https://lore.kernel.org/linux-arm-msm/[email protected]/

Changes in v10:
- Add R-b tags
- Remove unused fields from 'struct wcss_sec'
- Remove glink and ssr subdev if wcss_sec_probe() fails
- Link to v9: https://lore.kernel.org/linux-arm-msm/[email protected]/

Changes in v9:
- Add R-b from Konrad for dts patches
- Renamed qcom,wcss-sec-pil.yaml -> qcom,ipq5018-wcss-sec-pil.yaml
- Restore clocks & clock-names in above yaml
- Fix DCO on two patches
- Link to v8: https://lore.kernel.org/linux-arm-msm/[email protected]/

Changes in v8:
- Dropped Krzysztof's 'Reviewed-by' as the bindings file has changed significantly
* IPQ5018 support added in v6
* IPQ5424 support dropped in v8
* Updated to use IPQ9574 as example
- dt-bindings-check and dtbs-check passed
- Dropped IPQ5424 support from drivers/remoteproc/qcom_q6v5_wcss_sec.c
- Updated copyrights of drivers/remoteproc/qcom_q6v5_wcss_sec.c
- Change 'qcom,smem-state-names' order to resolve dt-bindings-check error in ipq5018.dtsi
- Dropped changes to ipq5424.dtsi
- Link to v7: https://lore.kernel.org/linux-arm-msm/[email protected]/

Changes in v7:
- correctly sorted QCOM_SCM_PIL_PAS_INIT_IMAGE_V2 by command ID
- correctly sorted smp2p-wcss nodes in dtsi files
- Link to v6: https://lore.kernel.org/r/[email protected]

Changes in v6:
- added patch to fix IPC register offset for ipq5424
- changed phandle description for mboxes property in dt-bindings
- updated bindings to define the right clocks per SoC based on
compatible. Ran make dt_binding_check for validation of all
SoCs
- use of more descriptive match data property (use_tmelcom) and
added a condition in wcss_start to not error out if tmelcom
isn't used
- mitigated potential off-by-one
- adopted use of of_reserved_mem_region_to_resource to acquire
memory-region resource
- added driver support for ipq5018 SoC
- corrected size of reg properties as per Konrad's comments
- added patch to bring up Q6 in ipq5018 dtsi
- Link to v5: https://lore.kernel.org/r/[email protected]

Changes in v5:
- retained all the patches as in v3 and addressed comments in v3.
- reverted changes to dt-bindings done in v4 and retained as in v3 and fixed firmware format from .mdt to .mbn and retained reviewed-by.
- dropped 2 patches in v4 that adds support for q6 dtb loading. Will post them as a new series.

Following tests were done:
- checkpatch
- dt_binding_check and dtbs_check
- Link to v4: https://lore.kernel.org/r/[email protected]

Changes in v4:
- changed q6 firmware image format from .mdt to .mbn
- corrected arrangement of variable assignemnts as per comments
in qcom_scm.c
- added scm call to get board machid
- added support for q6 dtb loading with support for additional
reserved memory for q6 dtb in .mbn format
- updated dt-bindings to include new dts entry qcom,q6-dtb-info
and additional item in memory-region for q6 dtb region.
- removed unnecessary dependency for QCOM_Q6V5_WCSS_SEC in
Kconfig
- removed unwanted header files in qcom_q6v5_wcss_sec.c
- removed repeated dtb parsing during runtime in qcom_q6v5_wcss_sec.c
- added required check for using tmelcom, if available. Enabled
fallback to scm based authentication, if tmelcom is unavailable.
- added necessary padding for 8digt hex address in dts
- Link to v3: https://lore.kernel.org/r/[email protected]

Following tests were done:
- checkpatch
- kernel-doc
- dt_binding_check and dtbs_check

Changes in v3:
- fixed copyright years and markings based on Jeff's comments.
- replaced devm_ioremap_wc() with ioremap_wc() in
wcss_sec_copy_segment().
- replaced rproc_alloc() and rproc_add() with their devres
counterparts.
- added mailbox call to tmelcom for secure image authentication
as required for IPQ5424. Added ipq5424 APCS comatible required.
- added changes to scm call to pass metadata size as required for
IPQ5332.
- Link to v2: https://lore.kernel.org/r/[email protected]

Changes in v2:
- Removed dependency of this series to q6 clock removal series
as recommended by Krzysztof
- Link to v1: https://lore.kernel.org/r/[email protected]

George Moussalem (1):
arm64: dts: qcom: ipq5018: add nodes to bring up q6

Manikanta Mylavarapu (4):
firmware: qcom_scm: ipq5332: add support to pass metadata size
dt-bindings: remoteproc: qcom: document hexagon based WCSS secure PIL
arm64: dts: qcom: ipq5332: add nodes to bring up q6
arm64: dts: qcom: ipq9574: add nodes to bring up q6

Vignesh Viswanathan (1):
remoteproc: qcom: add hexagon based WCSS secure PIL driver

 .../remoteproc/qcom,ipq5018-wcss-sec-pil.yaml | 178 ++++++++++
 arch/arm64/boot/dts/qcom/ipq5018.dtsi         |  64 ++++
 arch/arm64/boot/dts/qcom/ipq5332.dtsi         |  64 +++-
 arch/arm64/boot/dts/qcom/ipq9574.dtsi         |  60 +++-
 drivers/firmware/qcom/qcom_scm.c              |  14 +-
 drivers/firmware/qcom/qcom_scm.h              |   1 +
 drivers/remoteproc/Kconfig                    |  19 +
 drivers/remoteproc/Makefile                   |   1 +
 drivers/remoteproc/qcom_q6v5_wcss_sec.c       | 325 ++++++++++++++++++
 include/linux/remoteproc.h                    |   2 +
 10 files changed, 723 insertions(+), 5 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/remoteproc/qcom,ipq5018-wcss-sec-pil.yaml
 create mode 100644 drivers/remoteproc/qcom_q6v5_wcss_sec.c

To: Bjorn Andersson <[email protected]>
To: Konrad Dybcio <[email protected]>
To: Mathieu Poirier <[email protected]>
To: Rob Herring <[email protected]>
To: Krzysztof Kozlowski <[email protected]>
To: Conor Dooley <[email protected]>
To: Manikanta Mylavarapu <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
base-commit: next-20260710

Signature · 42 lines
2.34.1

Signed-off-by: Varadarajan Narayanan <[email protected]>
---
George Moussalem (1):
      arm64: dts: qcom: ipq5018: add nodes to bring up q6

Manikanta Mylavarapu (4):
      firmware: qcom_scm: ipq5332: add support to pass metadata size
      dt-bindings: remoteproc: qcom: document hexagon based WCSS secure PIL
      arm64: dts: qcom: ipq5332: add nodes to bring up q6
      arm64: dts: qcom: ipq9574: add nodes to bring up q6

Varadarajan Narayanan (3):
      arm64: dts: qcom: ipq5018: Enable q6v5_wcss
      arm64: dts: qcom: ipq5332: Enable q6v5_wcss
      arm64: dts: qcom: ipq9574: Enable q6v5_wcss

Vignesh Viswanathan (1):
      remoteproc: qcom: add hexagon based WCSS secure PIL driver

 .../remoteproc/qcom,ipq5018-wcss-sec-pil.yaml      | 178 +++++++++++
 arch/arm64/boot/dts/qcom/ipq5018-rdp432-c2.dts     |   4 +
 arch/arm64/boot/dts/qcom/ipq5018.dtsi              |  66 ++++
 arch/arm64/boot/dts/qcom/ipq5332-rdp-common.dtsi   |   4 +
 arch/arm64/boot/dts/qcom/ipq5332.dtsi              |  64 ++++
 arch/arm64/boot/dts/qcom/ipq9574-rdp-common.dtsi   |   4 +
 arch/arm64/boot/dts/qcom/ipq9574.dtsi              |  62 +++-
 drivers/firmware/qcom/qcom_scm.c                   |  16 +-
 drivers/firmware/qcom/qcom_scm.h                   |   1 +
 drivers/remoteproc/Kconfig                         |  20 ++
 drivers/remoteproc/Makefile                        |   1 +
 drivers/remoteproc/qcom_q6v5_wcss_sec.c            | 337 +++++++++++++++++++++
 include/linux/remoteproc.h                         |   2 +
 13 files changed, 754 insertions(+), 5 deletions(-)
---
base-commit: 9dba66b6217aacb924d997de3866e7e4c0dcf952
change-id: 20260710-rproc-c4f4d0c1f45c

Best regards,
-- 
Varadarajan Narayanan <[email protected]>