Skip to content

Make N-PHY support experimental

Larry Finger b43-dev linux-wireless 1 version New

Get series with b4
b4 am [email protected]

Versions newest first

  1. v1 Latest0 of 4 patches 0 repliesNew

Patches in v1 No applies recorded yet

None of the 4 patches the cover letter announces are in this archive.

Reviews trailers per patch

No Reviewed-by, Acked-by or Tested-by trailers for v1 yet.

Read the v1 thread

Cover letter [PATCH 0/4] Make N-PHY support experimental
Quoted 9 lines · Gábor Stefanik

2010/12/7 Rafał Miłecki <[email protected]>:

Quoted 1 line

Finally, thanks for Larry and Francesco I got b43 working with BCM4328 chipset!

Do you mean BCM4321 (14e4:4328)? BCM4328 is AFAIK handled by brcmfmac.

Quoted 4 lines

It's not perfectly stable yet, but scanning and associating to open network works! It has to be tested, improved, there are some PHY errors from time to time, but generally it works :)

With my device:

04:00.0 Network controller [0280]: Broadcom Corporation BCM4321 802.11a/b/g/n [14e4:4328] (rev 03)
Subsystem: Hewlett-Packard Company BCM4321 802.11a/b/g/n Wireless LAN
Controller [103c:1366]
Kernel driver in use: b43-pci-bridge

Excerpt of log:

[ 1184.780924] b43-pci-bridge 0000:04:00.0: PCI INT A -> Link[LK4E] -> GSI 20
(level, low) -> IRQ 20
[ 1184.780945] b43-pci-bridge 0000:04:00.0: setting latency timer to 64
[ 1184.800166] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x13, vendor 0x4243)
[ 1184.800176] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0C, vendor 0x4243)
[ 1184.800184] ssb: Core 2 found: PCI-E (cc 0x820, rev 0x04, vendor 0x4243)
[ 1184.800192] ssb: Core 3 found: PCI (cc 0x804, rev 0x0D, vendor 0x4243)
[ 1184.800200] ssb: Core 4 found: USB 1.1 Host (cc 0x817, rev 0x04, vendor 0x4243)
[ 1184.820062] ssb: Switching to ChipCommon core, index 0
[ 1184.820202] ssb: chipcommon status is 0x0
[ 1184.820211] ssb: SPROM offset is 0x1000
[ 1184.828653] ssb: SPROM revision 5 detected.
[ 1184.848037] ssb: Switching to PCI-E core, index 2
[ 1184.848659] ssb: Sonics Silicon Backplane found on PCI device 0000:04:00.0
[ 1184.897825] b43-phy0: Broadcom 4321 WLAN found (core revision 12)
[ 1184.916062] ssb: Switching to IEEE 802.11 core, index 1
[ 1184.940038] b43-phy0 debug: Found PHY: Analog 5, Type 4, Revision 2
[ 1184.940064] b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2055, Revision 4
[ 1184.975224] Registered led device: b43-phy0::tx
[ 1184.978455] Registered led device: b43-phy0::rx
[ 1184.980387] Registered led device: b43-phy0::radio
[ 1185.256050] b43-phy0: Loading firmware version 508.1107 (2009-06-26 19:16:02)
[ 1185.256059] ssb: Switching to ChipCommon core, index 0
[ 1185.256123] ssb: Switching to IEEE 802.11 core, index 1
[ 1185.332045] b43-phy0 debug: Chip initialized
[ 1185.333522] b43-phy0 debug: 64-bit DMA initialized
[ 1185.333570] b43-phy0 debug: QoS enabled
[ 1185.353497] b43-phy0 debug: Wireless interface started
[ 1185.353512] b43-phy0 debug: Adding Interface type 2
[ 1188.041790] b43-phy0 debug: Using hardware based encryption for keyidx: 0,
mac: c0:3f:0e:be:2b:45
[ 1191.134922] b43-phy0 debug: Disabling hardware based encryption for keyidx:
0, mac: c0:3f:0e:be:2b:45
[ 1192.823490] b43-phy0 debug: Using hardware based encryption for keyidx: 0,
mac: ff:ff:ff:ff:ff:ff
[ 1192.824306] b43-phy0 debug: Using hardware based encryption for keyidx: 1,
mac: ff:ff:ff:ff:ff:ff
[ 1192.824630] b43-phy0 debug: Using hardware based encryption for keyidx: 2,
mac: ff:ff:ff:ff:ff:ff
[ 1192.824989] b43-phy0 debug: Using hardware based encryption for keyidx: 3,
mac: ff:ff:ff:ff:ff:ff
[ 1194.896063] b43-phy0 ERROR: PHY transmission error

It connects and authenticates with WEP, but not with WPA2. It appears to be limited to CCK rates. Setting a rate above 11Mb/s results in complete failure.

Transmit rate is 4.6 Mb/s at 11M. All in all, not bad for first life.

Larry