Skip to content

i2c: improve s3c24x0 with High-speed and new SYS_I2C framework support

Heiko Schocher linux-i2c linux-samsung-soc lkml u-boot 1 version New

Get series with b4
b4 am [email protected]

Versions newest first

  1. v1 Latest0 of 3 patches 0 repliesNew

Patches in v1 No applies recorded yet

None of the 3 patches the cover letter announces are in this archive.

Reviews trailers per patch

No Reviewed-by, Acked-by or Tested-by trailers for v1 yet.

Read the v1 thread

Cover letter [U-Boot] [PATCH 0/3] i2c: improve s3c24x0 with High-speed and new SYS_I2C framework support

Hello Naveen,

Am 30.09.2013 08:58, schrieb Naveen Krishna Chatradhi:

Quoted 25 lines

This patchset fixes few bugs in the existing s3c24x0.c code (standard i2c) and add support for High-speed i2c bus controller available on Exynos5 SoCs from Samsung.

Exynos5250 channels [0 ~ 3] can configured for I2C contoller or
new HSI2C controller
channels [3 ~ 7] are standard I2C controller channels
Exynos5420 channels [0 ~ 3] are standard I2C controller channels and
channels [4 ~ 10] are High-speed controller channels

Patchset:
1. exynos: i2c: Fix i2c driver to handle NACKs properly Improvements and fixes from Vadim Bendebury for standard i2c calls

2. exynos: i2c: Change FDT bus setup code to enumerate ports correctly FDT bus setup code from Simon Glass

3. PATCH v5: i2c: s3c24xx: add hsi2c controller support High-speed controller register description and defines new i2c read/write, probe and set_bus calls.

This is been reviewed earlier at
http://lists.denx.de/pipermail/u-boot/2013-May/153245.html
Thanks for review and improvements from Vadim Bendebury.

Quoted 8 lines

Question:
4. RFC: samsung: i2c: Enable new CONFIG_SYS_I2C framework I've tried to implement the new I2C multi bus framework in u-boot tree, taking tegra-i2c.c as reference.

a). We have different number of channels on Exynos5250 and Exynos5420
(as explained above). How are we supposed to define the U_BOOT_I2C_ADAP_COMPLETE in such cases. Can i use #ifdef EXYNOS5420 or EXYNOS5250

From my side, Yes.

Quoted 25 lines

b). When i define 11 buses as in the case of Exynos5420, the "i2c bus" lists them
SMDK5420 # i2c bus

  Bus 0:  s3c0
  Bus 1:  s3c1
  Bus 2:  s3c10
  Bus 3:  s3c2
  Bus 4:  s3c3
  Bus 5:  s3c4
  Bus 6:  s3c5
  Bus 7:  s3c6
  Bus 8:  s3c7
  Bus 9:  s3c8
  Bus 10: s3c9
  or  (If i change the name to hsi2c)
  SMDK5420 # i2c bus
  Bus 0:  hsi2c10
  Bus 1:  hsi2c4
  Bus 2:  hsi2c5
  Bus 3:  hsi2c6
  Bus 4:  hsi2c7
  Bus 5:  hsi2c8
  Bus 6:  hsi2c9
  Bus 7:  s3c0
  Bus 8:  s3c1
  Bus 9:  s3c2
Quoted 4 lines

Bus 10: s3c3

Whats the expected behaviour. If the above result is correct, I need to changei the strings to get them in the correct order.

What, if you use two digits:

Bus 0: hsi2c01
Bus 1: hsi2c02
[...]
Bus 7: s3c00
Bus 8: s3c01
[...]

?

Or with one digit:

Bus 0: hsi2c1
Bus 1: hsi2c2
[...]
Bus 7: s3c0
Bus 8: s3c1
[...]

Quoted 5 lines

c). What's the alternative for the

    board_i2c_init(), i2c_get_bus_num_fdt(), i2c_reset_port_fdt().

"Functions to get the I2C bus number and reset I2C bus using FDT node"

I think, these functions are still needed.

Hmm.. that needs a general discussion, how to use fdt and i2c I think.

I would prefer a way (not really nowing, if it is possible for all configurations) where, if using fdt, the DT gets parsed and the availiable i2c buses gets created ... After that, "normal" i2c access with i2c_set_bus_num(), i2c_read/write should be possible ... this is currently not possible with the i2c framework, but should not be so hard to do. Except the restriction, that it would not work in SPL case, or before relocation for i2c buses announced through dt

Define CONFIG_SYS_I2C_MAX_HOPS -> CONFIG_SYS_I2C_DIRECT_BUS is not defined so i2c_bus[] is used in drivers/i2c/i2c_core.c. Define the fix i2c buses in the board config file with CONFIG_SYS_I2C_BUSES (if you have no fix buses, let this empty) and add a function in drivers/i2c/i2c_core.c, which adds new i2c buses to i2c_bus[] after the fix buses and call this new function, from where you interpret the fdt ...

int i2c_get_bus_num_fdt(int node) should be integrated to drivers/i2c/i2c_core.c

For what purpose is i2c_reset_port_fdt() ?

bye,
Heiko

Signature · 2 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany