Skip to content

drivers/misc: add rawio framework and drivers

Bin Gao lkml 1 version In review

Get series with b4
b4 am [email protected]

Versions newest first

  1. v1 Latest4 patches 8 repliesIn review

Patches in v1 No applies recorded yet

#Subject and filesSizeRepliesApplied
1/4drivers/misc: add rawio framework driverdrivers/misc/Kconfig drivers/misc/Makefile drivers/misc/rawio/Kconfig +3 more+108 -02 replies
2/4drivers/misc: add rawio pci driverdrivers/misc/rawio/Kconfig drivers/misc/rawio/Makefile drivers/misc/rawio/rawio_pci.c+18 -00 replies
3/4drivers/misc: add rawio iomem driverdrivers/misc/rawio/Kconfig drivers/misc/rawio/Makefile drivers/misc/rawio/rawio_iomem.c+15 -00 replies
4/4drivers/misc: add rawio i2c driverdrivers/misc/rawio/Kconfig drivers/misc/rawio/Makefile drivers/misc/rawio/rawio_i2c.c+60 -00 replies

Reviews trailers per patch

No Reviewed-by, Acked-by or Tested-by trailers for v1 yet.

Read the v1 thread

Cover letter [PATCH 0/4] drivers/misc: add rawio framework and drivers

To read/write registers from a device is very important on embedded system, especially SoC systems. Physically there could be different types of devices based on bus tyes, e.g. PCI devices, I2C (slave)devices, I/O devices(memory mapped), inter-processor devices, etc. Typically there are userland tools from
PC Linux to access device registers, but on some embedded system initrd and rootfs come with a minimal busybox and most useful userland tools are not available. To add these tools back to rootfs is not convenient either. What's more, on some systems with runtime pm enabled, reading/writing registers
from a device which is in low power state will cause problems. For these reasons, to have some tools/interfaces directly from kernel space via debug fs seems to be easy, cheap and convenient.

These patchsets are designed to achieve above goals to ease device driver and kernel debugging on embedded systems.

Rawio provides a framework to read/write registers from a bus, including pci, i2c, I/O device(memory mapped), etc. based on debug fs. Rawio bus drivers implement the read/write operation on a specific bus on top of the rawio framework driver.
Currently only three bus drivers are available: pci, iomem and i2c. But it's extremely easy to add more drivers on top of the framework if needed.

 drivers/misc/Kconfig             |   1 +
 drivers/misc/Makefile            |   1 +
 drivers/misc/rawio/Kconfig       |  59 +++++
 drivers/misc/rawio/Makefile      |   4 +
 drivers/misc/rawio/rawio.c       | 514
+++++++++++++++++++++++++++++++++++++++
 drivers/misc/rawio/rawio_i2c.c   | 224 +++++++++++++++++
 drivers/misc/rawio/rawio_iomem.c | 401 ++++++++++++++++++++++++++++++
 drivers/misc/rawio/rawio_pci.c   | 235 ++++++++++++++++++
 include/linux/rawio.h            |  78 ++++++
 9 files changed, 1517 insertions(+)
 create mode 100644 drivers/misc/rawio/Kconfig
 create mode 100644 drivers/misc/rawio/Makefile
 create mode 100644 drivers/misc/rawio/rawio.c
 create mode 100644 drivers/misc/rawio/rawio_i2c.c
 create mode 100644 drivers/misc/rawio/rawio_iomem.c
 create mode 100644 drivers/misc/rawio/rawio_pci.c
 create mode 100644 include/linux/rawio.h