Skip to content

RFC Introduce automatic DMA configuration for IOMMU masters

Marek Szyprowski linux-arm-kernel linux-iommu 1 version New

Get series with b4
b4 am [email protected]

Versions newest first

  1. v1 RFC Latest0 of 7 patches 0 repliesNew

Patches in v1 No applies recorded yet

None of the 7 patches the cover letter announces are in this archive.

Reviews trailers per patch

No Reviewed-by, Acked-by or Tested-by trailers for v1 yet.

Read the v1 thread

Cover letter [RFC PATCH 0/7] Introduce automatic DMA configuration for IOMMU masters

Hi Arnd,

Quoted 27 lines · Arnd Bergmann
Quoted 14 lines · On Tuesday 02 September 2014 12:42:13 Marek Szyprowski wrote:
Quoted 13 lines · Arnd Bergmann
Quoted 8 lines · On Tuesday 02 September 2014 10:48:02 Marek Szyprowski wrote:
Quoted 2 lines

-- I have concerns that allocating one domain per master might be
too much, but it's hard to tell without an IOMMU driver ported over.

One domain per master is IMHO a sane default configuration. The only default alternative I see is to have only one domain (related with dma-mapping subsystem) and bind all devices to it. However I really don't see any disadvantage of having separate domain per each master and such configuration
gives devices better separation.

I was expecting that the dma-mapping implementation would by default use one domain for all devices, since that is what the simpler IOMMUs without domain support have to do anyway.

Quoted 7 lines
Quoted 3 lines

For isolation purposes, it can only help to have more domains, but I would guess that there is some space overhead in maintaining lots of page tables.

I'm okay with both approaches (separate domain for each device vs. single common domain for all devices). Maybe this can be some kind of Kconfig option added to DMA debugging? Separation might be really helpful when debugging strange device behavior.

We should probably support the iommu=strict command line option that some other architectures have. This is mainly meant to ensure that IOTLBs are shot down as soon as the driver unmaps some memory, which you often want to avoid for performance reasons.

Quoted 5 lines

The iommu driver itself can then decide to also use separate domains for iommu=strict but a shared domain otherwise.

For hardware on which the shared domain is hard to do, the driver might always use separate domains.

Just to let you know, lazy unmapping is not yet implemented in ARM dma-mapping
implementation based on IOMMU.

Quoted 20 lines
Quoted 10 lines
Quoted 10 lines
Quoted 5 lines

However we also need to figure out how to let drivers to make their own configuration, like it is required by Exynos DRM subsystem, which consist of several devices, each having its own IOMMU controller, but for convenience those drivers assume that they all have been bound to the same, single domain.

IIRC with the way we ended up putting the mask into the iommu descriptor of the ARM SMMU, you can put multiple devices into the same iommu group, and have them automatically share a domain.

I don't know if the same would work for the Samsung implementation.

Quoted 10 lines

The question is how to transfer such information from the device drivers, that
need/benefit from such configuration to iommu driver, which does all the setup?
This is something completely internal to particular drivers and should not be
exported to device tree or userspace. Thierry suggested to hardcode this information in the iommu driver, but I'm looking for other approaches. Maybe simply releasing device from the default dma-mapping domain before attaching to custom one will be the easiest solution.

Quoted 7 lines

For the ARM SMMU, the problem is that there is not necessarily a good way to partition the masters into IOMMU groups automatically, therefore we want to provide some hints in DT. On a machine that can have more domains than it has masters, this is not a problem and we can always use an all-ones mask, but for a machine on which this is not the case, the problem is simplified a lot of we hardcode the masks in a way that can always work, putting multiple devices into an iommu group if necessary.

Well, I was talking about the Exynos IOMMU case, where there are no hw restrictions and grouping is done just to make things easier for the Exynos DRM drivers (a buffer gets the same DMA address for all devices, which are a part of virtual Exynos DRM device).

Quoted 3 lines

This is similar to how we do things for pinctrl, where you might have a theoretically endless space of options to set stuff up, but we can simplify it by defining the useful configurations.

Right, if hardware is limited, a sane working configuration is something that
should be encoded in device tree.

Best regards

Signature · 2 lines
Marek Szyprowski, PhD
Samsung R&D Institute Poland