Skip to content

Add support for pinctrl/gpio on Armada 37xx Was Re: [PATCH v2 0/7] Hi,

Gregory CLEMENT linux-arm-kernel linux-devicetree linux-gpio lkml 1 version In review

Get series with b4
b4 am [email protected]

Versions newest first

  1. v2 Latest0 of 7 patches 1 replyIn review

Patches in v2 No applies recorded yet

None of the 7 patches the cover letter announces are in this archive.

Reviews trailers per patch

No Reviewed-by, Acked-by or Tested-by trailers for v2 yet.

Read the v2 thread

Cover letter [PATCH v2 0/7] Add support for pinctrl/gpio on Armada 37xx Was Re: [PATCH v2 0/7] Hi,

Hi,

Obviously this cover letter is wrong. Actually I forgot to commit it in git series. Here it is the correct one:

After several months here it is the second version of the series adding support for the pin and gpio controllers present on the Armada 37xx SoCs.

Each Armada 37xx SoC comes with 2 pin controllers: one on the south bridge (managing 28 pins) and one on the north bridge (managing 36 pins).

At the hardware level the controller configure the pins by group and not pin by pin.

The gpio controller is also capable to handle interrupt from gpio.

In the second version several changes has been done:

- Update binding documentation making clear that mfd and syscon must be used (patch 1).

- Split the fist patch adding pin controller support for Armada 37xx in arm64 part (for kconfig) and pinctrl part (patch 2 and 3)

- Add MFD_SYSCON dependency (patch 3)

- Add kerneldoc for the armada_37xx_pin_group struct (patch 3)

- Rename _add_function() to armada_37xx_add_function() (patch 3)

- Use an inline function to update the reg offset (patch 4)

- Rename gpiolib_register to gpiochip_register (patch 4)

- Add a comment about the two registers limit (patch 4)

- Add explicit gpio node in the device tree (patch 4)

- Convert the driver to use GPIOLIB_IRQCHIP (patch 5)

- Add a critical section when accessing the hardware registers (patch 5)

- Use the gpio sub-node (patch 5)

With these change most of the comment of the first revision have been addressed.

Thanks,

Gregory

Gregory CLEMENT (7):
pinctrl: dt-bindings: Add documentation for Armada 37xx pin controllers
arm64: marvell: enable the Armada 37xx pinctrl driver
pinctrl: armada-37xx: Add pin controller support for Armada 37xx
pinctrl: armada-37xx: Add gpio support
pinctrl: aramda-37xx: Add irqchip support
ARM64: dts: marvell: Add pinctrl nodes for Armada 3700
ARM64: dts: marvell: armada37xx: add pinctrl definition

 Documentation/devicetree/bindings/clock/armada3700-xtal-clock.txt         |   7 +-
 Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt | 143 +++++++++++-
 arch/arm64/Kconfig.platforms                                              |   2 +-
 arch/arm64/boot/dts/marvell/armada-3720-db.dts                            |   8 +-
 arch/arm64/boot/dts/marvell/armada-37xx.dtsi                              |  71 +++++-
 drivers/pinctrl/Makefile                                                  |   2 +-
 drivers/pinctrl/mvebu/Kconfig                                             |   7 +-
 drivers/pinctrl/mvebu/Makefile                                            |   3 +-
 drivers/pinctrl/mvebu/pinctrl-armada-37xx.c                               | 918 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++-
 9 files changed, 1153 insertions(+), 8 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt
 create mode 100644 drivers/pinctrl/mvebu/pinctrl-armada-37xx.c

Sorry for the noise,

Gregory

Quoted 38 lines · Gregory CLEMENT

this series add support for the pin and gpio controllers present on the Armada 37xx SoCs.

Each Armada 37xx SoC comes with 2 pin controllers: one on the south bridge (managing 28 pins) and one on the north bridge (managing 36 pins).

At the hardware level the controller configure the pins by group and not pin by pin.

The gpio controller is also capable to handle interrupt from gpio.

Gregory

Gregory CLEMENT (7):
pinctrl: dt-bindings: Add documentation for Armada 37xx pin controllers
arm64: marvell: enable the Armada 37xx pinctrl driver
pinctrl: armada-37xx: Add pin controller support for Armada 37xx
pinctrl: armada-37xx: Add gpio support
pinctrl: aramda-37xx: Add irqchip support
ARM64: dts: marvell: Add pinctrl nodes for Armada 3700
ARM64: dts: marvell: armada37xx: add pinctrl definition

 Documentation/devicetree/bindings/clock/armada3700-xtal-clock.txt         |   7 +-
 Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt | 143 +++++++++++-
 arch/arm64/Kconfig.platforms                                              |   2 +-
 arch/arm64/boot/dts/marvell/armada-3720-db.dts                            |   8 +-
 arch/arm64/boot/dts/marvell/armada-37xx.dtsi                              |  71 +++++-
 drivers/pinctrl/Makefile                                                  |   2 +-
 drivers/pinctrl/mvebu/Kconfig                                             |   7 +-
 drivers/pinctrl/mvebu/Makefile                                            |   3 +-
 drivers/pinctrl/mvebu/pinctrl-armada-37xx.c                               | 918 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++-
 9 files changed, 1153 insertions(+), 8 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt
 create mode 100644 drivers/pinctrl/mvebu/pinctrl-armada-37xx.c

base-commit: c1ae3cfa0e89fa1a7ecc4c99031f5e9ae99d9201

Signature · 1 line
git-series 0.9.1
Signature · 4 lines
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com