Skip to content

Support for ATEVK1100 evaluation board

Gunnar Rangoy u-boot 1 version New

Get series with b4
b4 am [email protected]

Versions newest first

  1. v2 Latest9 patches 0 repliesNew

Patches in v2 No applies recorded yet

#Subject and filesSizeRepliesApplied
1/9Fix IP alignement problemnet/net.c+1 -12 replies
2/9AVR32: Make cacheflush cpu-dependentboard/atmel/atstk1000/flash.c board/earthlcd/favr-32-ezkit/flash.c cpu/at32ap/cache.c +3 more+5 -51 reply
3/9AVR32: Move addrspace.h to arch-directory, and move some functions from io.h to addrspace.hinclude/asm-avr32/addrspace.h include/asm-avr32/arch-at32ap700x/addrspace.h include/asm-avr32/io.h +1 more+87 -841 reply
4/9AVR32: Make GPIO implmentation cpu dependentinclude/asm-avr32/arch-at32ap700x/gpio-impl.h include/asm-avr32/arch-common/portmux-gpio.h+88 -811 reply
5/9AVR32: macb - Disable 100mbps if clock is slowdrivers/net/macb.c+11 -11 reply
5/9AVR32: macb - Disable 100mbps if clock is slow+0 -010 replies
6/9AVR32: macb - Search for PHY iddrivers/net/macb.c+31 -03 replies
7/9AVR32: Must add NOPs after disabling interrupts for AT32UC3A0512ESlib_avr32/interrupts.c+7 -01 reply
8/9AVR32: CPU support for AT32UC3A0xxx CPUscpu/at32uc/Makefile cpu/at32uc/at32uc3a0xxx/Makefile cpu/at32uc/at32uc3a0xxx/clk.c +25 more+2537 -01 reply
8/9AVR32: CPU support for AT32UC3A0xxx CPUs+0 -03 replies
9/9AVR32: Board support for ATEVK1100MAINTAINERS MAKEALL Makefile +5 more+455 -01 reply
9/9AVR32: Board support for ATEVK1100+0 -01 reply
9/9AVR32: Board support for ATEVK1100+0 -00 replies

Reviews trailers per patch

No Reviewed-by, Acked-by or Tested-by trailers for v2 yet.

Read the v2 thread

Cover letter [U-Boot] [PATCH v2 0/9] Support for ATEVK1100 evaluation board

This is a patch series which adds support for the ATEVK1100 evaluation board[1], and the AT32UC3A0xxx[2] microcontrollers used on that board. The patch series is based on avr32/next.

Some of these patches has already been submitted and most of the received feedback has been addressed. We would like to thank you for all the received feedback, and say thay we are sorry for the long delay.

This microcontroller is similar to the AT32AP700x, which is already supported by U-Boot, and this code is therefore based on that.

Patch 1 makes a change which works around a bug in the compiler. Patch 2-7 makes changes to other avr32-code in preparation for support of the new microcontroller.
Patch 8 adds support for the AT32UC3A0xxx microcontrollers.
Patch 9 adds support for the ATEVK1100 evaluation board.

The current revisions of the microcontroller have a bug in the SDRAM-controller, which makes it unreliable to run code from SDRAM. We therefore currently don't use SDRAM, but rather SRAM.

Changes since last time:
- Merged the two patch-series.
- Config option for searching for phy-address.
- Config option for limiting macb speed to 10 Mbps.
- Changed serial port speed to 115200.
- Some cleanups.

What works:
Loading U-Boot, serial console, loading image over dhcp/tftp, booting image.

[1] http://www.atmel.com/dyn/Products/tools_card.asp?tool_id=4114
[2] http://www.atmel.com/products/avr32/uc3/uc3_2.asp?family_id=682