piix_pci cleanup

Hi

v3:
- rebase to today git. Fix conflicts with avi pic/isa cleanup.

v2:
- bit the bullet, change irq_opaque to void *, instead of qemu_irq * that allows us to pass anything there.
- Rearrange piix_pci to be able to add piix3_dev to the irq_state
- Once rearrangmente is fixed, make sane SaveVM *_load/_save() functions. We can still load old state, but we only write the sane one.

mips_malta can do a similar cleanup, it is not difficult to do. But I can't test it.

About irq_state in i440fx_init(). It would have been easier, if there were a way to create i440FX-pcihost giving it the already allocated variable. Basically:

pci_bus = pci_register_bus() -> needs irq_state
i440fx = pci_create_simple(pci_bus, ..) -> needs pci_bus piix3 = pci_create_simple (pci_bus, ...) -> needs pci_bus

irq_state -> needs piix3

We have a nice circular dependency here. to fix it, I just create an empty irq_state, passed it to pci_register_bus() and fill it later.

It would have been a bit cleaner if there were a finction like i440fx = pci_create_simple_here(..., &i440fx).

Later, Juan.

v1:
- split piix4 from piix_pci. The only shared code where piix_save/load, i.e. almost nothing. Once there, compile piix4.o only for mips (it was not used anywhere else).
- Move global variables to PCII440FXState. Nice and clean until....
- pci_irq_levels: This is great:
* it is saved/loaded from i440fx
* it is cleaned during reset in piix3
* it is used in piix3_set_irq, that don't receive neither i440fx nor piix state, it needs to be a global variable. (created a global link until a better solution appear).

I looked where to "hide" pci_irq_levels and piix3_dev (both needed in piix3_set_irq), and didn't found where to pass them, out of:
- hack i8259 to hide it into PicState2 (that one got passed through the pic) ugly for words, but will work
- try to add <something> at setup_irq time, but at that point we have:
* opaque -> pci_dev of device that we are working with
* from there we can get to the bus that the device is attached to, but no way to go from there to the Host bridge (that is what we wanted in the 1st place)

Later, Juan.

Juan Quintela (13):
piix4 don't use pci_irq_levels at all
Split piix4 support from piix_pci.c
low_set_irq is not used anywhere
Use PCII440FXState instead of generic PCIDevice Move smm_enabled and isa_memory_mappings to PCII440FXState We want the argument pass to set_irq to be opaque Create PIIX3State instead of using PCIDevice for PIIX3 Introduce PIIX3IrqState for piix3 irq's state Fold piix3_init() intto i440fx_init
We can add piix3_dev now to PIIX3IrqState
Save irq_state into PCII440FXState pci_irq_levels[] belong to PIIX3State
Update SaveVM versions

 Makefile.target    |    2 +-
 hw/apb_pci.c       |    4 +-
 hw/grackle_pci.c   |    4 +-
 hw/gt64xxx.c       |    3 +-
 hw/pc.c            |    5 +-
 hw/pc.h            |   11 ++-
 hw/pci.c           |    8 +-
 hw/pci.h           |    6 +-
 hw/piix4.c         |  127 +++++++++++++++++++++++++++
 hw/piix_pci.c      |  246 +++++++++++++++++++++-------------------------------
 hw/ppc4xx_pci.c    |    4 +-
 hw/ppce500_pci.c   |    4 +-
 hw/prep_pci.c      |    4 +-
 hw/r2d.c           |    4 +-
 hw/sh_pci.c        |    4 +-
 hw/unin_pci.c      |    4 +-
 hw/versatile_pci.c |    4 +-
 17 files changed, 270 insertions(+), 174 deletions(-)
 create mode 100644 hw/piix4.c