zynq COMMON_CLK support

This patchset implements COMMON_CLK support for the zynq. At this point, only the basic fundamental clocks are modelled, and only passively; for rate calculation. of_clk bindings are implemented to allow specifying clock/peripheral relationships in the device tree.

Patch 1 and 2 are a followup to my early patch: "ARM: zynq: move ttc timer code to drivers/clocksource". Patch 1 moves the definition sys_timer definition out of the ttc code, and into the zynq common code. Patch 2 is the actual rename, and makefile cleanup.

Patch 3 adds a description of the second uart to zynq-ep107.dts. I did this pre-split (patch 4), because I felt it might make reviewing easier.

Patch 4 uses zynq-ep107.dts as a reference to create zynq-7000.dtsi, which is intended to be a common dtsi snippet for inclusion in describing zynq-7000 based boards. zynq-zc702.dts is created as an example consumer. The zynq-ep107.dts file is removed entirely (it describes, presumably, a board not available to consumers).

Patch 5 is the real meat; it adds an implementation of the clk models for the PLLs, the CPU clock network, and basic (simplified) clk models for the essential peripherals (UART and the TTC).

Patch 6 removes CONFIG_OF conditional code from the xilinx uart driver. The zynq kernel requires CONFIG_OF, and this hardware is not currently used on any other non CONFIG_OF platform.

Patch 7 adds support to the xilinx_uartps driver to allow getting clock rate information form the device tree.

Patch 8 implements DT support for the ttc, including pulling clock tree info.

---
There are some specific concerns that I had that I would like some guidance on:

Two identical timers on the board have historically been statically allocated to act as the system clocksource, and the clockevent_device. With patch 8, this distinction is done in the device tree by tweaking with the compatible properties of which of the timers you want used for what purpose.

I feel, however, that this is an abuse of the device tree, which should only be used to describe hardware, not to layout a policy on how the hardware is used.

So, if it's not in the device tree, then where? Do I go back to the static allocation routine, such that the first matching ttc node in the tree becomes the clockevent_device, and the second one a clocksource? That seems like a hack.

Is it somehow possible to have all of the timers registered as both a clocksource and a clockevent_device, and have some higher level logic make the policy decision as to which timer is used for what?

An additional question regarding of_clk bindings:

	my_clock {
		#clock-cells = <0>;
		clock-output-names = "my_out_clock";
	};
	node_a {
		clocks = <&clk>;
		clock-names = "my_clock";
		clock-ranges;

		node_b {
			/* ... */
		};
	};

In this scenario, should I be expecting of_clk_get(node_b, 0) to retrieve a handle to parent's consumed clock (due to clock-ranges)? I could make this work using of_clk_get_by_name(node_b, "my_clock"), but I was somewhat surprised the former didn't work.

Thanks (and sorry for the novel),
Josh

---
Josh Cartwright (8):
ARM: zynq: move arm-specific sys_timer out of ttc
ARM: zynq: move ttc timer code to drivers/clocksource
ARM: zynq: dts: add description of the second uart
ARM: zynq: dts: split up device tree
ARM: zynq: add COMMON_CLK support
serial: xilinx_uartps: kill CONFIG_OF conditional
serial: xilinx_uartps: get clock rate info from dts
clocksource: xilinx_ttc: add OF_CLK support

 .../devicetree/bindings/clock/zynq-7000.txt        |  55 ++++
 arch/arm/Kconfig                                   |   1 +
 arch/arm/boot/dts/Makefile                         |   1 +
 arch/arm/boot/dts/zynq-7000.dtsi                   | 166 ++++++++++
 arch/arm/boot/dts/zynq-ep107.dts                   |  63 ----
 arch/arm/boot/dts/zynq-zc702.dts                   |  44 +++
 arch/arm/mach-zynq/Makefile                        |   2 +-
 arch/arm/mach-zynq/common.c                        |  29 +-
 arch/arm/mach-zynq/timer.c                         | 298 -----------------
 drivers/clk/Makefile                               |   1 +
 drivers/clk/clk-zynq.c                             | 355 +++++++++++++++++++++
 drivers/clocksource/Makefile                       |   1 +
 drivers/clocksource/xilinx_ttc.c                   | 326 +++++++++++++++++++
 drivers/tty/serial/xilinx_uartps.c                 |  39 +--
 include/linux/clk/zynq.h                           |  24 ++
 .../common.h => include/linux/xilinx_ttc.h         |   8 +-
 16 files changed, 1022 insertions(+), 391 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/clock/zynq-7000.txt
 create mode 100644 arch/arm/boot/dts/zynq-7000.dtsi
 delete mode 100644 arch/arm/boot/dts/zynq-ep107.dts
 create mode 100644 arch/arm/boot/dts/zynq-zc702.dts
 delete mode 100644 arch/arm/mach-zynq/timer.c
 create mode 100644 drivers/clk/clk-zynq.c
 create mode 100644 drivers/clocksource/xilinx_ttc.c
 create mode 100644 include/linux/clk/zynq.h
 rename arch/arm/mach-zynq/common.h => include/linux/xilinx_ttc.h (81%)

1.8.0