net: Add support for Synopsys DesignWare XPCS
Get series with b4
b4 am [email protected]Versions newest first
- v1 Latest8 patches 3 repliesIn review
Patches in v1 No applies recorded yet
| # | Subject and files | Size | Replies | Applied |
|---|---|---|---|---|
| 1/8 | net: stmmac: selftests: Do not fail if PHY is not attacheddrivers/ | +1 | 0 replies | |
| 2/8 | net: stmmac: Switch to linkmode_and()/linkmode_andnot()drivers/ | +5 | 0 replies | |
| 3/8 | net: stmmac: Fallback to dev_fwnode() if neededdrivers/ | +3 | 0 replies | |
| 4/8 | net: stmmac: Use resolved link config in mac_link_up()drivers/ | +33 | 0 replies | |
| 5/8 | net: phylink: Add missing Backplane speedsdrivers/ | +2 | 0 replies | |
| 6/8 | net: phylink: Test if MAC/PCS support Autonegdrivers/ | +3 | 0 replies | |
| 7/8 | net: phy: Add Synopsys DesignWare XPCS MDIO moduleMAINTAINERS drivers/ drivers/ +2 more | +667 | 2 replies | |
| 8/8 | net: stmmac: Integrate it with DesignWare XPCSdrivers/ drivers/ drivers/ +3 more | +58 | 0 replies |
Reviews trailers per patch
No Reviewed-by, Acked-by or Tested-by trailers for v1 yet.
Cover letter [PATCH net-next 0/8] net: Add support for Synopsys DesignWare XPCS
This adds support for Synopsys DesignWare XPCS in net subsystem and integrates it into stmmac.
At 1/8, we start by removing the limitation of stmmac selftests that needed a PHY to pass all the tests.
Then at 2/8 we use some helpers in stmmac so that some code can be simplified.
At 3/8, we fallback to dev_fwnode() so that PCI based setups wich may not have CONFIG_OF can still use FW node.
At 4/8, we adapt stmmac to the new PHYLINK changes as suggested by Russell King.
We proceed by doing changes in PHYLINK in order to support XPCS: At 5/8 we add some missing speeds that USXGMII supports and at 6/8 we check if Autoneg is supported after initial parameters are validated.
Support for XPCS is finally introduced at 7/8, along with the usage of it in stmmac driver at 8/8.
---
Cc: Giuseppe Cavallaro <[email protected]>
Cc: Alexandre Torgue <[email protected]>
Cc: Jose Abreu <[email protected]>
Cc: "David S. Miller" <[email protected]>
Cc: Jakub Kicinski <[email protected]>
Cc: Maxime Coquelin <[email protected]>
Cc: Russell King <[email protected]>
Cc: Andrew Lunn <[email protected]>
Cc: Florian Fainelli <[email protected]>
Cc: Heiner Kallweit <[email protected]>
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
Cc: [email protected]
---
Jose Abreu (8):
net: stmmac: selftests: Do not fail if PHY is not attached
net: stmmac: Switch to linkmode_and()/linkmode_andnot()
net: stmmac: Fallback to dev_fwnode() if needed
net: stmmac: Use resolved link config in mac_link_up()
net: phylink: Add missing Backplane speeds
net: phylink: Test if MAC/PCS support Autoneg
net: phy: Add Synopsys DesignWare XPCS MDIO module
net: stmmac: Integrate it with DesignWare XPCS
MAINTAINERS | 7 + drivers/net/ethernet/stmicro/stmmac/Kconfig | 1 + drivers/net/ethernet/stmicro/stmmac/common.h | 3 + drivers/net/ethernet/stmicro/stmmac/hwif.h | 12 + drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 96 ++-- drivers/net/ethernet/stmicro/stmmac/stmmac_mdio.c | 27 + .../net/ethernet/stmicro/stmmac/stmmac_selftests.c | 2 +- drivers/net/phy/Kconfig | 6 + drivers/net/phy/Makefile | 1 + drivers/net/phy/mdio-xpcs.c | 612 +++++++++++++++++++++ drivers/net/phy/phylink.c | 5 + include/linux/mdio-xpcs.h | 41 ++ include/linux/stmmac.h | 1 + 13 files changed, 771 insertions(+), 43 deletions(-) create mode 100644 drivers/net/phy/mdio-xpcs.c create mode 100644 include/linux/mdio-xpcs.h
Signature · 1 line
2.7.4