Skip to content

Add support for I2C Legacy/FRU decoding

Michal Simek u-boot 1 version New

Get series with b4
b4 am [email protected]

Versions newest first

  1. v1 Latest4 patches 0 repliesNew

Patches in v1 No applies recorded yet

#Subject and filesSizeRepliesApplied
1/4xilinx: common: Add Makefile to common folderboard/xilinx/common/Makefile board/xilinx/versal/Makefile board/xilinx/zynq/Makefile +1 more+7 -30 replies
2/4xilinx: cmd: Add support for FRU commandsboard/xilinx/Kconfig board/xilinx/common/Makefile board/xilinx/common/fru.c +3 more+414 -00 replies
3/4xilinx: cmd: Add basic fru format generatorboard/xilinx/common/fru.c board/xilinx/common/fru.h board/xilinx/common/fru_ops.c+136 -20 replies
4/4xilinx: board: Add FRU decoder supportboard/xilinx/common/board.c+82 -10 replies

Reviews trailers per patch

No Reviewed-by, Acked-by or Tested-by trailers for v1 yet.

Read the v1 thread

Cover letter [PATCH 0/4] Add support for I2C Legacy/FRU decoding

Hi,

the whole series add support for I2C based FRU eeprom board identification. EEPROMs are referenced by nvmem alias which was suggested by Rob Herring (dt maintainer). Previous code was using chosen xlnx,eeprom property. And because no platform is setting up nvmem alias the code is doing nothing on all boards.

If you want to try it and test it just choose board and define nvmem aliases and you should see similar logs like this.

zcu104 with legacy format and FRU on FMC

U-Boot 2020.10-00835-g819dc03ff784 (Oct 20 2020 - 12:48:12 +0200)

Model: ZynqMP ZCU104 RevC
Board: Xilinx ZynqMP
DRAM:  2 GiB
PMUFW:  v1.1
Xilinx I2C Legacy format at nvmem0:
 Board name:    zcu104
 Board rev:     c
 Board SN:      895527361843-94820
 Ethernet mac:  00:0a:35:04:eb:93

Xilinx I2C FRU format at nvmem1:
Manufacturer Name: XILINX
Product Name: XXX-XXX
Serial No: 1231
Part Number: dd
File ID: U-Boot generator
Revision Number: rev_A

EL Level:       EL2
Chip ID:        zu7e
WDT:   Started with servicing (60s timeout)
NAND:  0 MiB
MMC:   mmc at ff170000: 0

Loading Environment from FAT... *** Warning - bad CRC, using default environment

In:    serial at ff000000
Out:   serial at ff000000
Err:   serial at ff000000
Bootmode: LVL_SHFT_SD_MODE1
Reset reason:   EXTERNAL

Net:
ZYNQ GEM: ff0e0000, mdio bus ff0e0000, phyaddr 12, interface rgmii-id
eth0: ethernet at ff0e0000
Hit any key to stop autoboot: 0
ZynqMP>

Based on https://lists.denx.de/pipermail/u-boot/2020-October/429382.html

Thanks,
Michal

Michal Simek (3):
xilinx: common: Add Makefile to common folder
xilinx: cmd: Add basic fru format generator
xilinx: board: Add FRU decoder support

Siva Durga Prasad Paladugu (1):
xilinx: cmd: Add support for FRU commands

 board/xilinx/Kconfig            |   8 +
 board/xilinx/common/Makefile    |  10 +
 board/xilinx/common/board.c     |  83 +++++++-
 board/xilinx/common/fru.c       |  91 ++++++++
 board/xilinx/common/fru.h       |  83 ++++++++
 board/xilinx/common/fru_ops.c   | 362 ++++++++++++++++++++++++++++++++
 board/xilinx/versal/Makefile    |   1 -
 board/xilinx/zynq/Makefile      |   1 -
 board/xilinx/zynqmp/MAINTAINERS |   1 +
 board/xilinx/zynqmp/Makefile    |   1 -
 10 files changed, 637 insertions(+), 4 deletions(-)
 create mode 100644 board/xilinx/common/Makefile
 create mode 100644 board/xilinx/common/fru.c
 create mode 100644 board/xilinx/common/fru.h
 create mode 100644 board/xilinx/common/fru_ops.c
Signature · 1 line
2.28.0