Skip to content

RFC btrfs: read_policy types latency, device and

Anand Jain linux-block linux-btrfs 1 version In review

Get series with b4
b4 am [email protected]

Versions newest first

  1. v1 RFC Latest7 patches 9 repliesIn review

Patches in v1 No applies recorded yet

#Subject and filesSizeRepliesApplied
1/7block: export part_stat_read_allblock/genhd.c include/linux/genhd.h+3 -12 replies
2/7block: export part_stat_read_inflightblock/genhd.c include/linux/genhd.h+13 -82 replies
3/7btrfs: add read_policy latencyfs/btrfs/sysfs.c fs/btrfs/volumes.c fs/btrfs/volumes.h+76 -21 reply
4/7btrfs: trace, add event btrfs_read_policyfs/btrfs/volumes.c include/trace/events/btrfs.h+46 -23 replies
5/7btrfs: introduce new device-state read_preferredfs/btrfs/sysfs.c fs/btrfs/volumes.h+56 -00 replies
6/7btrfs: introduce new read_policy devicefs/btrfs/sysfs.c fs/btrfs/volumes.c fs/btrfs/volumes.h+25 -11 reply
7/7btrfs: introduce new read_policy round-robinfs/btrfs/sysfs.c fs/btrfs/volumes.c fs/btrfs/volumes.h+71 -10 replies

Reviews trailers per patch

No Reviewed-by, Acked-by or Tested-by trailers for v1 yet.

Read the v1 thread

Cover letter [PATCH RFC 0/7] btrfs: read_policy types latency, device and

Based on mainline 5.10-rc1

Depends on the following 3 patches in the mailing list.
btrfs: add btrfs_strmatch helper
btrfs: create read policy framework
btrfs: create read policy sysfs attribute, pid

Patch 1-3 adds new read policy: latency.
Patch 4 adds tracing function.
Patch 5-6 were sent before they add read policy: device. Patch 7 adds new read policy: round-robin.

I am sending this patchset to receive feedback, comments, and more test results. Few cleanups, optimization, and broader performance test are may be possible. This patchset does not alter the original default read_policy that is PID.

This has been tested on VMs only, as my hardware based test host is currently down.

This patchset adds read policies type latency, device, and round-robin.

These policies are for the mirrored raid profiles such as raid1, raid1c3, raid1c4, and raid10 as they provide a choice to read from any one of the given devices or any one pair of devices for raid10 for a given block.

Latency:

Latency read policy routes the read IO based on the historical average wait time experienced by the read IOs on the individual device factored by 1/10 of inflight commands in the queue. I need to add a factor of 1/10 because for most of the block devices the queue depth is more than 1, and there can be commands in the queue even before the previous commands have completed. However, the factor 1/10 for the inflight commands is yet to be fine-tuned. Suggestions are welcome.

Device:

With the device read policy along with the read_preferred flag, you can set the device to be used for reading manually. Useful to test mirrors in a deterministic way and helps advance system administrations.

Round-robin:

When set picks the next device to read in the round-robin loop. To achieve this first we put the stripes in an array, sort it by devid and pick the next device.

The test results from my VM with 2 devices of type sata and 2 devices of type virtio, are as below.

Here below I have included a few scripts which were useful for testing.

-------------------8<--------------------------------

$ cat readpolicyset
#!/bin/bash

: ${1?"arg1 <mnt> missing"}
: ${2?"arg2 <pid|latency|device|roundrobin> missing"}

mnt=$1
policy=$2
[ $policy == "device" ] && { : ${3?"arg3 <devid> missing"}; } devid=$3

uuid=$(btrfs fi show -m /btrfs | grep uuid | awk '{print $4}') p=/sys/fs/btrfs/$uuid/read_policy q=/sys/fs/btrfs/$uuid/devinfo

[ $policy == "device" ] && { echo 1 > ${q}/$devid/read_preferred || exit $?; }

echo $policy > $p
exit $? -------------------8<--------------------------------

$ cat readpolicy
#!/bin/bash

: ${1?"arg1 <mnt> missing"}
mnt=$1

uuid=$(btrfs fi show -m /btrfs | grep uuid | awk '{print $4}') p=/sys/fs/btrfs/$uuid/read_policy q=/sys/fs/btrfs/$uuid/devinfo

policy=$(cat $p)
echo -n "$policy ( "

for i in $(find $q -type f -name read_preferred | xargs cat) do

	echo -n "$i"

done
echo ")" -------------------8<--------------------------------

$ cat readstat 
#!/bin/bash

: ${1?"arg1 <mnt> is missing"}
: ${2?"arg2 <cmd-to-run> is missing"}

mnt=$1; shift
mountpoint -q $mnt || { echo "ERROR: $mnt is not mounted"; exit 1; }

declare -A devread

for dev in $(btrfs filesystem show -m $mnt | grep devid |awk '{print $8}') do

	prefix=$(echo $dev | rev | cut -d"/" -f1 | rev)
	sysfs_path=$(find /sys | grep $prefix/stat$)

	devread[$sysfs_path]=$(cat $sysfs_path | awk '{print $1}')

done

"$@" | grep "READ: bw"

echo
echo
for sysfs_path in ${!devread[@]}
do

	dev=$(echo $sysfs_path | rev | cut -d"/" -f2 | rev)
	new=$(cat $sysfs_path | awk '{print $1}')
	old=${devread[$sysfs_path]}
	echo "$dev $((new - old))"

done -------------------8<--------------------------------

$ cat fioread 
#!/bin/bash

: ${1?"arg1 </mnt/file> is missing"}
: ${2?"arg2 <1Gi|50Gi> is missing"}

tf=$1
sz=$2
mnt=$(stat -c '%m' $tf)

fio \
--filename=$tf \
--directory=$mnt \
--filesize=$sz \
--size=$sz \
--rw=randread \
--bs=64k \
--ioengine=libaio \
--direct=1 \
--numjobs=32 \
--group_reporting \
--thread \
--name iops-test-job -------------------8<--------------------------------

Here below are the performance results for raid1c4, raid10, and raid1.

The workload is fio read 32 threads, 500m random reads.

Fio is passed to the script readstat, which returns the number of read IOs per device sent during the fio.

Few inferences:

1.
In some cases as mine, PID is also associated with the stripe 0 being circulating among the devices at the chunk level before moving to the next device. So PID is not a bad option for such configurations. However, it is not a good choice if the devices are heterogeneous in terms of type, speed, and size.

2.
Latency provides performance equal to PID on my test setup. But needs iostat be enabled. And there is a cost of calculating the avg wait time. (If you factor in the similar cost to PID using the test code [1] then latency's performance is better than PID. So that proves that read IO distribution as per latency is really working)

3.
Round robin is worst (unless there is a bug in my patch). As the total number of new IOs issued was almost double compared to the PID and the latency read_policy, that's because I think there was a fewer number of merges due to constant switching of devices.

4.
Device read_policy is quite useful in testing and advance sysadmin maintenance. When known how to use, this policy could help to avert too many csum errors in midest of peak production.

Supporting fio logs are below. And readstat shows the number of read IOs issued to devices (excluding the merges).

raid1c4
-------

pid:

$ readpolicyset /btrfs pid && readpolicy /btrfs && dropcache && readstat /btrfs fioread /btrfs/largefile 500m
[pid] latency device roundrobin ( 0000)
 READ: bw=87.0MiB/s (91.2MB/s), 87.0MiB/s-87.0MiB/s (91.2MB/s-91.2MB/s), io=15.6GiB (16.8GB), run=183884-183884msec

vdb 64060
vdc 64053
sdb 64072
sda 64054

latency: (All devices are non-rotational, but sda and sdb are of type sata and vdb and vdc are of type virtio).

$ readpolicyset /btrfs latency && readpolicy /btrfs && dropcache && readstat /btrfs fioread /btrfs/largefile 500m

pid [latency] device roundrobin ( 0000)
READ: bw=87.1MiB/s (91.3MB/s), 87.1MiB/s-87.1MiB/s (91.3MB/s-91.3MB/s), io=15.6GiB (16.8GB), run=183774-183774msec

vdb 255844
vdc 559
sdb 0
sda 93

roundrobin:

$ readpolicyset /btrfs roundrobin && readpolicy /btrfs && dropcache && readstat /btrfs fioread /btrfs/largefile 500m

pid latency device [roundrobin] ( 0000)
READ: bw=51.0MiB/s (54.5MB/s), 51.0MiB/s-51.0MiB/s (54.5MB/s-54.5MB/s), io=15.6GiB (16.8GB), run=307755-307755msec

vdb 866859
vdc 866651
sdb 864139
sda 865533

raid10
------

pid:

$ readpolicyset /btrfs pid && readpolicy /btrfs && dropcache && readstat /btrfs fioread /btrfs/largefile 500m
[pid] latency device roundrobin ( 0000)
 READ: bw=85.2MiB/s (89.3MB/s), 85.2MiB/s-85.2MiB/s (89.3MB/s-89.3MB/s), io=15.6GiB (16.8GB), run=187864-187864msec

sdf 64053
sde 64036
sdd 64043
sdc 64038

latency:

$ readpolicyset /btrfs latency && readpolicy /btrfs && dropcache && readstat /btrfs fioread /btrfs/largefile 500m
pid [latency] device roundrobin ( 0000)
 READ: bw=85.4MiB/s (89.5MB/s), 85.4MiB/s-85.4MiB/s (89.5MB/s-89.5MB/s), io=15.6GiB (16.8GB), run=187370-187370msec

sdf 117494
sde 10748
sdd 125247
sdc 2921

roundrobin:

$ readpolicyset /btrfs roundrobin && readpolicy /btrfs && dropcache && readstat /btrfs fioread /btrfs/largefile 500m
pid latency device [roundrobin] ( 0000)
 READ: bw=55.4MiB/s (58.1MB/s), 55.4MiB/s-55.4MiB/s (58.1MB/s-58.1MB/s), io=15.6GiB (16.8GB), run=288701-288701msec

sdf 617593
sde 617381
sdd 618486
sdc 618633

raid1:

$ readpolicyset /btrfs pid && readpolicy /btrfs && dropcache && readstat /btrfs fioread /btrfs/largefile 500m
[pid] latency device roundrobin ( 00)
 READ: bw=78.8MiB/s (82.6MB/s), 78.8MiB/s-78.8MiB/s (82.6MB/s-82.6MB/s), io=15.6GiB (16.8GB), run=203158-203158msec

sdb 128087
sda 128090

$ readpolicyset /btrfs latency && readpolicy /btrfs && dropcache && readstat /btrfs fioread /btrfs/largefile 500m
pid [latency] device roundrobin ( 00)
 READ: bw=86.5MiB/s (90.7MB/s), 86.5MiB/s-86.5MiB/s (90.7MB/s-90.7MB/s), io=15.6GiB (16.8GB), run=185023-185023msec

sdb 567
sda 255942

From the latency test results we know sda is providing low latency read IO. So set sda as read proffered device.

$ readpolicyset /btrfs device 1 && readpolicy /btrfs && dropcache && readstat /btrfs fioread /btrfs/largefile 500m
pid latency [device] roundrobin ( 10)
 READ: bw=88.2MiB/s (92.5MB/s), 88.2MiB/s-88.2MiB/s (92.5MB/s-92.5MB/s), io=15.6GiB (16.8GB), run=181374-181374msec

sdb 0
sda 256191

$ readpolicyset /btrfs roundrobin && readpolicy /btrfs && dropcache && readstat /btrfs fioread /btrfs/largefile 500m
pid latency device [roundrobin] ( 00)
 READ: bw=54.1MiB/s (56.7MB/s), 54.1MiB/s-54.1MiB/s (56.7MB/s-56.7MB/s), io=15.6GiB (16.8GB), run=295693-295693msec

sdb 1252584
sda 1254258

Thanks, Anand

------------------
[1]

fs/btrfs/volumes.c +6 -0
index d3023879bdf6..72ec633e9063 100644
@@ -5665,6 +5665,12 @@ static int find_live_mirror(struct btrfs_fs_info *fs_info,
 fs_info->fs_devices->read_policy = BTRFS_READ_POLICY_PID;
 fallthrough;
 case BTRFS_READ_POLICY_PID:
+ /*
+ * Just to factor in the cost of calculating the avg wait using
+ * iostat for testing.
+ */
+ btrfs_find_best_stripe(fs_info, map, first, num_stripes, log,
+ logsz);
 preferred_mirror = first + current->pid % num_stripes;
 scnprintf(log, logsz,
 "first %d num_stripe %d %s (%d) preferred %d",

Anand Jain (7):
block: export part_stat_read_all
block: export part_stat_read_inflight
btrfs: add read_policy latency
btrfs: trace, add event btrfs_read_policy
btrfs: introduce new device-state read_preferred
btrfs: introduce new read_policy device
btrfs: introduce new read_policy round-robin

 block/genhd.c                |  22 ++--
 fs/btrfs/sysfs.c             |  59 ++++++++++-
 fs/btrfs/volumes.c           | 188 ++++++++++++++++++++++++++++++++++-
 fs/btrfs/volumes.h           |   5 +
 include/linux/genhd.h        |   3 +
 include/trace/events/btrfs.h |  20 ++++
 6 files changed, 286 insertions(+), 11 deletions(-)
Signature · 1 line
2.25.1