Skip to content

board: freescale: add T2080RDB rev D support

Camelia Groza u-boot 1 version In review

Get series with b4
b4 am [email protected]

Versions newest first

  1. v1 Latest4 patches 1 replyIn review

Patches in v1 No applies recorded yet

#Subject and filesSizeRepliesApplied
1/4board: freescale: t208xrdb: detect the board revision letterboard/freescale/t208xrdb/t208xrdb.c+17 -20 replies
2/4board: freescale: t208xrdb: add rev D support for the non-DM_ETH modeboard/freescale/t208xrdb/eth_t208xrdb.c include/configs/T208xRDB.h+19 -50 replies
3/4board: freescale: t208xrdb: add Linux fdt fixups for rev Dboard/freescale/t208xrdb/eth_t208xrdb.c board/freescale/t208xrdb/t208xrdb.c board/freescale/t208xrdb/t208xrdb.h+35 -00 replies
4/4board: freescale: t208xrdb: add a config option for rev D dts fixupsarch/powerpc/dts/t2080rdb.dts board/freescale/t208xrdb/Kconfig configs/T2080RDB_revD_NAND_defconfig +3 more+363 -00 replies

Reviews trailers per patch

No Reviewed-by, Acked-by or Tested-by trailers for v1 yet.

Read the v1 thread

Cover letter [PATCH 0/4] board: freescale: add T2080RDB rev D support

From: Camelia Groza <[email protected]>

The T2080RDB boards revision D and up have updated Aquantia PHYs on the two 10Gbps copper ports connected to MAC1 and MAC2 (from AQ1202 to AQR113C). The second PHY connected to MAC2 is located at a different address on the MDIO bus compared to revision C boards. Device tree fixups are required for both Linux and u-boot to set the correct PHY address for the new board revisions.

The first patch in the series implements a callback that detects the board revision based on the CPLD registers.

The second patch updates the PHY addresses in u-boot for the legacy, non-DM, driver implementation.

The third patch adds a fixup for Linux's device tree that is called from both DM and non-DM code paths.

The last patch corrects u-boot's device tree under DM based on a newly introduced CONFIG_T2080RDB_REV_D build option. We are unable to use the board_fix_fdt callback to update the device tree before relocation because the dts is stored in flash at that point and isn't writable. Instead, the config option is used until a more robust solution is implemented. Defconfig targets with the config option enabled by default are added for convenience.

Camelia Groza (4):
board: freescale: t208xrdb: detect the board revision letter
board: freescale: t208xrdb: add rev D support for the non-DM_ETH mode
board: freescale: t208xrdb: add Linux fdt fixups for rev D
board: freescale: t208xrdb: add a config option for rev D dts fixups

 arch/powerpc/dts/t2080rdb.dts            |  7 ++
 board/freescale/t208xrdb/Kconfig         |  4 +
 board/freescale/t208xrdb/eth_t208xrdb.c  | 49 ++++++++++++-
 board/freescale/t208xrdb/t208xrdb.c      | 20 ++++-
 board/freescale/t208xrdb/t208xrdb.h      |  1 +
 configs/T2080RDB_revD_NAND_defconfig     | 93 ++++++++++++++++++++++++
 configs/T2080RDB_revD_SDCARD_defconfig   | 90 +++++++++++++++++++++++
 configs/T2080RDB_revD_SPIFLASH_defconfig | 92 +++++++++++++++++++++++
 configs/T2080RDB_revD_defconfig          | 77 ++++++++++++++++++++
 include/configs/T208xRDB.h               |  8 +-
 10 files changed, 434 insertions(+), 7 deletions(-)
 create mode 100644 configs/T2080RDB_revD_NAND_defconfig
 create mode 100644 configs/T2080RDB_revD_SDCARD_defconfig
 create mode 100644 configs/T2080RDB_revD_SPIFLASH_defconfig
 create mode 100644 configs/T2080RDB_revD_defconfig

--
2.17.1