Skip to content

board: freescale: T2080RDB: rev D support and

Camelia Groza u-boot 1 version New

Get series with b4
b4 am [email protected]

Versions newest first

  1. v1 Latest0 of 4 patches 0 repliesNew

Changes in v2 from the cover letter

- remove legacy non-DM_ETH code paths at Tom's recommendation in 1/4
- patch title and description rewordings in 2/4 and 3/4
- drop "board: freescale: t208xrdb: add rev D support for the non-DM_ETH mode"
- move the AQR113C_PHY_ADDR define from the dropped patch to 3/4

Patches in v1 No applies recorded yet

None of the 4 patches the cover letter announces are in this archive.

Reviews trailers per patch

PatchTom Rini
SeriesR-b

Trailers given in replies are filled; those carried in the patches from earlier versions are outlined with dashes.

Read the v1 thread

Cover letter [PATCH 0/4] board: freescale: T2080RDB: rev D support and

From: Camelia Groza <[email protected]>

The T2080RDB boards revision D and up have updated Aquantia PHYs on the two 10Gbps copper ports connected to MAC1 and MAC2 (from AQ1202 to AQR113C). The second PHY connected to MAC2 is located at a different address on the MDIO bus compared to revision C boards. Device tree fixups are required for both Linux and u-boot to set the correct PHY address for the new board revisions.

While we are here, the first patch cleans up the T2080RDB board files and removes legacy non-DM_ETH code paths. DM_ETH and DM_PCI are enabled, so board_eth_init() isn't required anymore.

The second patch in the series implements a callback that detects the board revision based on the CPLD registers.

The third patch adds the PHY address fix-up for Linux's device tree.

The last patch corrects u-boot's device tree under DM based on a newly introduced CONFIG_T2080RDB_REV_D build option. We are unable to use the board_fix_fdt callback to update the device tree before relocation because the dts is stored in flash at that point and isn't writable. Instead, this config option is used until a more robust solution is implemented. Defconfig targets with the config option enabled by default are added for convenience.

Changes in v2:
- remove legacy non-DM_ETH code paths at Tom's recommendation in 1/4
- patch title and description rewordings in 2/4 and 3/4
- drop "board: freescale: t208xrdb: add rev D support for the non-DM_ETH mode"
- move the AQR113C_PHY_ADDR define from the dropped patch to 3/4

Camelia Groza (4):
board: freescale: t208xrdb: remove the legacy non-DM_ETH code
board: freescale: t208xrdb: detect the board revision version
board: freescale: t208xrdb: add Linux fdt fix-ups for rev D
board: freescale: t208xrdb: add a config option for rev D dts fixups

 arch/powerpc/dts/t2080rdb.dts            |   7 ++
 board/freescale/t208xrdb/Kconfig         |   4 +
 board/freescale/t208xrdb/eth_t208xrdb.c  | 112 +++++++----------------
 board/freescale/t208xrdb/t208xrdb.c      |  24 +++--
 board/freescale/t208xrdb/t208xrdb.h      |   1 +
 configs/T2080RDB_revD_NAND_defconfig     |  93 +++++++++++++++++++
 configs/T2080RDB_revD_SDCARD_defconfig   |  90 ++++++++++++++++++
 configs/T2080RDB_revD_SPIFLASH_defconfig |  92 +++++++++++++++++++
 configs/T2080RDB_revD_defconfig          |  77 ++++++++++++++++
 include/configs/T208xRDB.h               |   8 +-
 10 files changed, 422 insertions(+), 86 deletions(-)
 create mode 100644 configs/T2080RDB_revD_NAND_defconfig
 create mode 100644 configs/T2080RDB_revD_SDCARD_defconfig
 create mode 100644 configs/T2080RDB_revD_SPIFLASH_defconfig
 create mode 100644 configs/T2080RDB_revD_defconfig

--
2.17.1