More Midisport 2x2 troubles
Hi all,
I just upgraded to Mdk 9.1 and reinstalled all of the MIDI-related stuff, as well as the Alsa 0.9.2 (from sources, after uninstalling Mdk's RPM's). I also installed Fernando's modified alsasound script that enables smart unloading of snd- modules.
The end result is that the midisport works, well sort of.
The firmware loads fine, and the midisport is properly recognized. The problem is that I only have one MIDI port available even though this is the 2x2 version (I had 2 ports in Mdk 9.0, usually /dev/midi(0) and /dev/midi1). Now I only have /dev/midi.
The interesting thing is that the /proc/asound/card1/midi0 lists the following:
Output 0
Tx bytes : 0
Output 1
Tx bytes : 0
Input 0
Rx bytes : 5 (this number changes, most likely because
it's the only port that has anything hooked up to it) Input 1
Rx bytes : 0
So, it seems that there are 2 I and 2 O ports, but they are all allocated within the midi0 device according to the proc stuff (or /dev/midi1 according to the dev stuff). If this is the case, then how do I access the second port.
Cat /dev/midi1 only outputs stuff coming into the first port, so that tells me something's fishy.
I am using CCRMA's hotplug 8_26_1 and ezusbmidi 2002_11_17.
There were no alterations to the kernel or any other part of the system (apart from the alsa install and other audio software installs).
My modules.conf looks like this:
# ALSA portion
alias char-major-116 snd
alias char-major-14 soundcore
alias snd-card-0 snd-intel8x0
alias sound-slot-0 snd-card-0
alias snd-card-1 snd-hdsp
alias sound-slot-1 snd-card-1
alias snd-card-2 snd-usb-audio
alias sound-slot-2 snd-card-2
options snd major=116 cards_limit=4 device_mode=0666 device_gid=0 device_uid=0
options snd-intel8x0 index=0
options snd-hdsp index=1
options snd-usb-audio vid=0x763 pid=0x1001 index=2
# CS4205
alias sound-service-0-0 snd-mixer-oss
#alias sound-service-0-1 snd-seq-oss
alias sound-service-0-3 snd-pcm-oss
#alias sound-service-0-8 snd-seq-oss
alias sound-service-0-12 snd-pcm-oss
#HDSP
alias sound-service-1-0 snd-mixer-oss
alias sound-service-1-1 snd-seq-oss
alias sound-service-1-3 snd-pcm-oss
alias sound-service-1-8 snd-seq-oss
alias sound-service-1-12 snd-pcm-oss
#MIDISPORT
alias sound-service-2-1 snd-seq-oss
alias sound-service-2-8 snd-seq-oss
In this situation the hdsp is not in use, so midisport assumes the 2nd card position.
Upon midisport reconnect, the /var/log/messages spits out the following:
Apr 2 23:59:49 badass-bukvic kernel: usb.c: USB disconnect on device 00:1d.2-1 address 29 Apr 3 00:00:00 badass-bukvic kernel: hub.c: new USB device 00:1d.2-1, assigned address 30 Apr 3 00:00:00 badass-bukvic kernel: usb.c: USB device 30 (vend/prod 0x763/0x1001) is not claimed by any active driver. Apr 3 00:00:03 badass-bukvic /etc/hotplug/usb.agent: Setup ezusbmidi for USB product 763/1001/1 Apr 3 00:00:03 badass-bukvic /etc/hotplug/usb.agent: Module setup ezusbmidi for USB product 763/1001/1 Apr 3 00:00:03 badass-bukvic /etc/hotplug/usb/ezusbmidi: load /usr/share/usb/ezusbmidi/ezusbmidi2x2.ihx for 763/1001/1 to /proc/bus/usb/002/030 Apr 3 00:00:03 badass-bukvic kernel: usb.c: USB disconnect on device 00:1d.2-1 address 30 Apr 3 00:00:03 badass-bukvic kernel: hub.c: new USB device 00:1d.2-1, assigned address 31 Apr 3 00:00:07 badass-bukvic /etc/hotplug/usb.agent: Setup snd-usb-audio audio usb-midi for USB product 763/1110/1 Apr 3 00:00:07 badass-bukvic /etc/hotplug/usb.agent: ... blacklisted module: audio Apr 3 00:00:07 badass-bukvic /etc/hotplug/usb.agent: ... blacklisted module: usb-midi Apr 3 00:00:07 badass-bukvic /etc/hotplug/usb.agent: Setup alsasound for USB product 763/1110/1 Apr 3 00:01:00 badass-bukvic modprobe: modprobe: Can't locate module
sound-service-2-2
(NB: what's up with the sound-service-2-2, is there such a thing?)
Upon doing this, cat /dev/midi1 is the only one that works.
Other pertinent info is (in abbreviated form):/proc/asound/version -> ALSA=0.92 kernel=2.4.21-0.13mdk ../cards -> 0 i810, 1 2x2 (Midisport) at usb-00:1d.2-1 ../card1/ has id and midi0 files only
All I also remember the last time when I was using 0.9.0 is that I had to upgrade from CVS in order to get both ports (it was the snd-usb-audio bug IIRC). But now, I did d/l and install 0.9.2 which should have those fixes but I can't seem to get the second port to work. Could it be that there's something leftover from the mdk 0.9.0 version of Alsa even after I did rpm -e and reinstalled 0.9.2 from sources?
Any help on this issue is greatly appreciated! Sincerely,
Ivica Ico Bukvic, multimedia sculptor
http://meowing.ccm.uc.edu/~ico
-------------------------------------------------------
This SF.net email is sponsored by: ValueWeb:
Dedicated Hosting for just $79/mo with 500 GB of bandwidth! No other company gives more support or power for your dedicated server
http://click.atdmt.com/AFF/go/sdnxxaff00300020aff/direct/01/