Skip to contentSkip to conversation

[U-Boot] [Add tlbentry problem]

U-Boot 김영순 3 participants 3 messages Aug 18, 2008 – Sep 9, 2008

lore
Share & tools
lore

김영순

author
#0 lore raw

I?ve worked on my custum board based on SEQUOIA.

I?d like to add new device (DSP, SIZE=256M, CS4).

I added tlbentry(256M) in init.S and defined CS4 in sequoia.h.

Init.S:

           /* TLB-entry for EBC(DSP) */

          tlbentry( CFG_DSP_BASE, SZ_256M, CFG_DSP_BASE, 1,

AC_R|AC_W|AC_X|SA_G|SA_I )

sequoia.h:

#define CFG_DSP_BASE 0xd0000000

#define CFG_EBC_PB4AP 0x05014300

#define CFG_EBC_PB4CR (CFG_DSP_BASE | 0x3a000)

The problem is this.

When I access over 2Mbytes area of DSP4(Over d0200000), I?ve got bus error in my application.

Accessing to under 2Mbytes, it works well?.

Are there anything to do, when I want to attatch new devices????

Best Regards?

#1 lore raw
Quoted 19 lines · ???

I?ve worked on my custum board based on SEQUOIA.

I?d like to add new device (DSP, SIZE=256M, CS4).

I added tlbentry(256M) in init.S and defined CS4 in sequoia.h.

Init.S:

           /* TLB-entry for EBC(DSP) */

          tlbentry( CFG_DSP_BASE, SZ_256M, CFG_DSP_BASE, 1,

AC_R|AC_W|AC_X|SA_G|SA_I )

Quoted 7 lines

sequoia.h:

#define CFG_DSP_BASE 0xd0000000

#define CFG_EBC_PB4AP 0x05014300

#define CFG_EBC_PB4CR (CFG_DSP_BASE | 0x3a000)

With this you defined the bank size to 2MB. So a bus error for access "after" these 2MB is to be expected. Try this instead:

#define CFG_EBC_PB4CR (CFG_DSP_BASE | 0xfa000)

This will only cover 128MB though as this is the max for an EBC bank size.

Best regards,
Stefan

=====================================================================
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
=====================================================================

#2 lore raw
In reply to 김영순

Hi Yshim:
Please check your EBC CR value, if you configure for 2M, then thats what you will get.

Feng Kan

Quoted 54 lines · ???

I?ve worked on my custum board based on SEQUOIA.

I?d like to add new device (DSP, SIZE=256M, CS4).

I added tlbentry(256M) in init.S and defined CS4 in sequoia.h.

Init.S:

           /* TLB-entry for EBC(DSP) */

          tlbentry( CFG_DSP_BASE, SZ_256M, CFG_DSP_BASE, 1,

AC_R|AC_W|AC_X|SA_G|SA_I )

sequoia.h:

#define CFG_DSP_BASE 0xd0000000

#define CFG_EBC_PB4AP 0x05014300

#define CFG_EBC_PB4CR (CFG_DSP_BASE | 0x3a000)

The problem is this.

When I access over 2Mbytes area of DSP4(Over d0200000), I?ve got bus error in my application.

Accessing to under 2Mbytes, it works well?.

Are there anything to do, when I want to attatch new devices????

Best Regards?