st0: Block limits 1 - 16777215 bytes.
I've been experiencing mysterious lockups since upgrading to kernel 2.4.17. Looking in the /var/log/messages I hadn't seen anything suspicious until now. I guess the machine hasn't had time to write this to disk except every now and then. The message
Feb 19 11:29:55 butler kernel: st0: Block limits 1 - 16777215 bytes.
I notice this after rebooting after the crash. So I tried manually doing a tar to the tape drive and was able to successfully lock the machine up. Can someone help me understand this and if it is simply a limit problem, why would the machine lock up?
Thank you.
Glover George
Systems/Networks Admin
Gulf Sales & Supply, Inc.
(228) 762-0268
[email protected]
http://www.gulfsales.com
Hello Glover , I get the same messages & do not get system lock ups . Might try sending a little bit more info about what is going on around any of the lock ups . If you can reliably lock up the system by accessing the tape drive . Then send some info to the list about the system & the tape drive and how it is attached to the system . Hth , JimL
ps: All disk & tape drives are scsi .
Tyan Thunder HE-SL Dual s370 M.B.
# lspci 00:00.0 Host bridge: Relience Computer CNB20HE (rev 23) 00:00.1 PCI bridge: Relience Computer CNB20HE (rev 01) 00:00.2 Host bridge: Relience Computer: Unknown device 0006 (rev 01) 00:00.3 Host bridge: Relience Computer: Unknown device 0006 (rev 01) 00:01.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR): Unknown device 0021 (rev 01) 00:01.1 SCSI storage controller: Symbios Logic Inc. (formerly NCR): Unknown device 0021 (rev 01) BTW these are a Symbios 53c1010 chip on board . 00:02.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 09) 00:04.0 PCI bridge: Intel Corporation 80960RP [i960 RP Microprocessor/Bridge] (rev 05) 00:04.1 RAID bus controller: Mylex Corporation DAC960PX (rev 05) Is a DAC960PL 00:07.0 Ethernet controller: Intel Corporation 82557 [Ethernet Pro 100] (rev 08) 00:0f.0 ISA bridge: Relience Computer: Unknown device 0200 (rev 51) 00:0f.1 IDE interface: Relience Computer: Unknown device 0211 00:0f.2 USB Controller: Relience Computer: Unknown device 0220 (rev 04) 01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 PF
# cat /proc/cpuinfo Below x 2 .
processor : 0 ( & 1 )vendor_id : GenuineIntel
cpu family : 6
model : 8
model name : Pentium III (Coppermine)
stepping : 10
cpu MHz : 849.158
cache size : 256 KBfdiv_bug : nohlt_bug : nof00f_bug : nocoma_bug : no
fpu : yesfpu_exception : yes
cpuid level : 2
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse
bogomips : 1690.82
Quoted 22 lines · Glover George
I've been experiencing mysterious lockups since upgrading to kernel 2.4.17. Looking in the
/var/log/messagesI hadn't seen anything suspicious until now. I guess the machine hasn't had time to write this to disk except every now and then. The messageFeb 19 11:29:55 butler kernel: st0: Block limits 1 - 16777215 bytes.I notice this after rebooting after the crash. So I tried manually doing a tar to the tape drive and was able to successfully lock the machine up. Can someone help me understand this and if it is simply a limit problem, why would the machine lock up?
Thank you.
Glover George
Systems/Networks Admin
Gulf Sales & Supply, Inc.
(228) 762-0268
[email protected]
http://www.gulfsales.com
Quoted 6 lines
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
+------------------------------------------------------------------+
| James W. Laferriere | System Techniques | Give me VMS |
| Network Engineer | P.O. Box 854 | Give me Linux |
| [email protected] | Coudersport PA 16915 | only on AXP |
+------------------------------------------------------------------+Ok, after playing with it a little more I found out that the message I'm getting about the block sizes isn't related to the lockups. I can lock the system up by tar'ing up the /proc directory (why are you tar'ing the /proc directory!!! I know!!! But that's not the point). I had no problem with RH 7.2's supplied 7.2 kernel (2.4.7-10). However, this is 2.4.17 (with the linux-abi patch).
I have been able to make succesful backups as long as I ignore the /proc directory but something must be wrong. Doing an "ls -la *" doesn't lock the machine though. Only when tar'ing it (I suppose because of a read). It doesn't lock up consistently in the same place when reading from the proc directory however, but always in the proc. I made about 15 test runs and they all died in proc and --exclude proc doesn't cause it to lock somewhere else.
I guess the question is (and I've had it for a while) is how do I get the system to log more info for me? I'm a little new a debugging the kernel, but I did compile most of the debugging into a test kernel. However, the system hard locks with no oops or anything in the logs. The system must be shutdown by holding the power button in for 4 seconds. I know this must not be a huge problem because no ones mentioned it, so I'd like to do some more investigating on my part. Thanks for your help.
Quoted 24 lines
Hello Glover , I get the same messages & do not get system lock ups . Might try sending a little bit more info about what is going on around any of the lock ups . If you can reliably lock up the system by accessing the tape drive . Then send some info to the list about the system & the tape drive and how it is attached to the system . Hth , JimL
ps: All disk & tape drives are scsi .Quoted 10 lines · Glover George
I've been experiencing mysterious lockups since upgrading to kernel 2.4.17. Looking in the
/var/log/messagesI hadn't seen anything suspicious until now. I guess the machine hasn't had time to write this to disk except every now and then. The messageFeb 19 11:29:55 butler kernel: st0: Block limits 1 - 16777215 bytes.I notice this after rebooting after the crash. So I tried manually doing a tar to the tape drive and was able to successfully lock the machine up. Can someone help me understand this and if it
is simply a
Quoted 2 lines
limit problem, why would the machine lock up?
Quoted 7 lines · Glover George
Ok, after playing with it a little more I found out that the message I'm getting about the block sizes isn't related to the lockups. I can lock the system up by tar'ing up the /proc directory (why are you tar'ing the /proc directory!!! I know!!! But that's not the point). I had no problem with RH 7.2's supplied 7.2 kernel (2.4.7-10). However, this is 2.4.17 (with the linux-abi patch).
Quoted 7 lines
I have been able to make succesful backups as long as I ignore the /proc directory but something must be wrong. Doing an "ls -la *" doesn't lock the machine though. Only when tar'ing it (I suppose because of a read). It doesn't lock up consistently in the same place when reading from the proc directory however, but always in the proc. I made about 15 test runs and they all died in proc and --exclude proc doesn't cause it to lock somewhere else.
You do not tar /proc! There is kcore there! tar thinks it's a real file. Reading (accessing) some kernel areas will cause a deadlock.
If you don't want to --exclude proc, then umount it before your backups. FYI, it's SOP to backup different mounted file-systems so you don't end up backing up N disks on a single media. Therefore your tar sequence would be something like:
tar -czlf root.tar.gz /
tar -czlf user.tar.gz /user
|________ stay on the same file-system.
..etc..
Since /proc is a seperate file-system, you never have problems like you describe and the mount-point gets backed up as required.
Cheers,
Dick Johnson
Penguin : Linux version 2.4.1 on an i686 machine (797.90 BogoMips).
111,111,111 * 111,111,111 = 12,345,678,987,654,321