Skip to contentSkip to conversation

qemu does not work for the latest image?

DISCUSSION Yong Li 2 participants 3 messages Nov 15, 2018 – Nov 16, 2018

lore
Share & tools
lore

Yong Li

author
#0 lore raw

Hi All,

Previously I can use qemu to test these built images, but it does not work now and get the below error messages:

Just want to know if there is any command/options changes? Or it does not support now?

qemu-system-arm -m 256 -M witherspoon-bmc -nographic -drive file=tmp/deploy/images/witherspoon/obmc-phosphor-image-poon.ubi.mtd,format=r aw,if=mtd

qemu-system-arm: Aspeed iBT has no chardev backend

U-Boot 2016.07 (Nov 15 2018 - 06:18:37 +0000)

Watchdog enabled

DRAM: 240 MiB

Flash: 32 MiB

*** Warning - bad CRC, using default environment

In: serial

Out: serial

Err: serial

Net: aspeednic#0

Error: aspeednic#0 address not set.

Hit any key to stop autoboot: 0

ubi0: attaching mtd1

ubi0: scanning is finished

UBI init error 12

Error, no UBI device/partition selected!

Wrong Image Format for bootm command

ERROR: can't get kernel image!

Thanks,

Yong

#1 lore raw
Quoted 7 lines · Yong Li

Hi All,

Previously I can use qemu to test these built images, but it does not work now and get the below error messages:
Just want to know if there is any command/options changes? Or it does not support now?

Hey Yong, I pulled down the latest qemu binary and witherspoon image and it booted up fine for me.

Here were my commands:
wget https://openpower.xyz/job/openbmc-qemu-build-merge-x86/lastSuccessfulBuild/artifact/qemu/arm-softmmu/qemu-system-arm
wget https://openpower.xyz/job/openbmc-build/distro=ubuntu,label=builder,target=witherspoon/lastSuccessfulBuild/artifact/deploy/images/witherspoon/obmc-phosphor-image-witherspoon.ubi.mtd
./qemu-system-arm -m 256 -M witherspoon-bmc -nographic -drive
file=./obmc-phosphor-image-witherspoon.ubi.mtd,format=raw,if=mtd -net
nic -net user,hostfwd=:127.0.0.1:2622-:22,hostfwd=:127.0.0.1:2643-:443,hostfwd=:127.0.0.1:8580-:80,hostname=qemu

Quoted 51 lines

qemu-system-arm -m 256 -M witherspoon-bmc -nographic -drive file=tmp/deploy/images/witherspoon/obmc-phosphor-image-poon.ubi.mtd,format=raw,if=mtd

qemu-system-arm: Aspeed iBT has no chardev backend

U-Boot 2016.07 (Nov 15 2018 - 06:18:37 +0000)

Watchdog enabled

DRAM: 240 MiB

Flash: 32 MiB

*** Warning - bad CRC, using default environment

In: serial

Out: serial

Err: serial

Net: aspeednic#0

Error: aspeednic#0 address not set.

Hit any key to stop autoboot: 0

ubi0: attaching mtd1

ubi0: scanning is finished

UBI init error 12

Error, no UBI device/partition selected!

Wrong Image Format for bootm command

ERROR: can't get kernel image!

Thanks,

Yong

author
#2 lore raw

Thanks Andrew for your commands.  The issue is caused by my older qemu tool.

After downloaded qemu-system-arm, I can boot the image now!

Thanks,
Yong

Quoted 68 lines · Andrew Geissler
Quoted 6 lines · Yong Li

Hi All,

Previously I can use qemu to test these built images, but it does not work now and get the below error messages:
Just want to know if there is any command/options changes? Or it does not support now?

Hey Yong, I pulled down the latest qemu binary and witherspoon image and it booted up fine for me.

Here were my commands:
wgethttps://openpower.xyz/job/openbmc-qemu-build-merge-x86/lastSuccessfulBuild/artifact/qemu/arm-softmmu/qemu-system-arm wgethttps://openpower.xyz/job/openbmc-build/distro=ubuntu,label=builder,target=witherspoon/lastSuccessfulBuild/artifact/deploy/images/witherspoon/obmc-phosphor-image-witherspoon.ubi.mtd ./qemu-system-arm -m 256 -M witherspoon-bmc -nographic -drive
file=./obmc-phosphor-image-witherspoon.ubi.mtd,format=raw,if=mtd -net
nic -net user,hostfwd=:127.0.0.1:2622-:22,hostfwd=:127.0.0.1:2643-:443,hostfwd=:127.0.0.1:8580-:80,hostname=qemu

Quoted 51 lines

qemu-system-arm -m 256 -M witherspoon-bmc -nographic -drive file=tmp/deploy/images/witherspoon/obmc-phosphor-image-poon.ubi.mtd,format=raw,if=mtd

qemu-system-arm: Aspeed iBT has no chardev backend

U-Boot 2016.07 (Nov 15 2018 - 06:18:37 +0000)

Watchdog enabled

DRAM: 240 MiB

Flash: 32 MiB

*** Warning - bad CRC, using default environment

In: serial

Out: serial

Err: serial

Net: aspeednic#0

Error: aspeednic#0 address not set.

Hit any key to stop autoboot: 0

ubi0: attaching mtd1

ubi0: scanning is finished

UBI init error 12

Error, no UBI device/partition selected!

Wrong Image Format for bootm command

ERROR: can't get kernel image!

Thanks,

Yong