Skip to contentSkip to conversation

Limiting bandwidth to entire LAN

LARTC Gastón 3 participants 6 messages Mar 4, 2004 – Mar 7, 2004

lore
Share & tools
lore

Gastón

author
#0 lore raw

Hi, first of all thanks for all your help. I`m using a bridge and I want to assign the lan (with public routable ips) only 512Kbits (The internet link is 1Mbit). What i thought was creating a class with a ceil of 512Kbit an applying a filter to it with the entire net (1.2.3.0/24). This approach didn´t work for me(the ceil was bypassed). Should I use policing instead?

These are the commands I used:

tc qdisc del dev eth0 root
tc qdisc add dev eth0 root handle 1 htb default 10 r2q 5

tc qdisc del dev eth1 root
tc qdisc add dev eth1 root handle 1 htb default 10 r2q 5

tc class add dev eth0 parent 1: classid 1:2 htb rate 512Kbit

tc class add dev eth0 parent 1:2 classid 1:30 htb rate 448Kbit ceil 512Kbit tc qdisc add dev eth0 parent 1:30 handle 30 sfq perturb 10
tc filter add dev eth0 parent 1:0 protocol ip prio 100 u32 match ip src 1.2.3.0/24 classid 1:30

tc class add dev eth1 parent 1: classid 1:2 htb rate 512Kbit

tc class add dev eth1 parent 1:2 classid 1:30 htb rate 448Kbit ceil 512Kbit tc qdisc add dev eth1 parent 1:30 handle 30 sfq perturb 10
tc filter add dev eth1 parent 1:0 protocol ip prio 100 u32 match ip dst 1.2.3.0/24 classid 1:30

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw

Hi Gastón,

Quoted 5 lines

tc filter add dev eth0 parent 1:0 protocol ip prio 100 u32 match ip src 1.2.3.0/24 classid 1:30

tc filter add dev eth1 parent 1:0 protocol ip prio 100 u32 match ip dst 1.2.3.0/24 classid 1:30

I'm pretty sure you want 'flowid 1:30' instead of classid on the filters.

To my knowledge, the classid is declaring the filter to have that class, instead of directing the matching to the class with that id.

Although, taking a quick look through the doco, I can't see anywhere where it explicitly says what the flowid does, maybe it's just assumed because all the examples are like that.

regards

Signature · 11 lines
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Damion de Soto - Software Engineer  email:     [email protected]
SnapGear - A CyberGuard Company ---    ph:         +61 7 3435 2809
  | Custom Embedded Solutions          fax:         +61 7 3891 3630
  | and Security Appliances            web: http://www.snapgear.com
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  ---  Free Embedded Linux Distro at   http://www.snapgear.org  ---

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#2 lore raw
In reply to Gastón
Quoted 5 lines · Gastón

Hi, first of all thanks for all your help. I`m using a bridge and I want to assign the lan (with public routable ips) only 512Kbits (The internet link is 1Mbit). What i thought was creating a class with a ceil of 512Kbit an applying a filter to it with the entire net (1.2.3.0/24). This approach didn´t work for me(the ceil was bypassed). Should I use policing instead?

Can you check the counters with tc -s -d class dev eth1 to see if the filters are working ?

Stef

Signature · 7 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.openprojects.net
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#3 lore raw
In reply to Gastón
Quoted 5 lines · Damion de Soto

Hi Gastón,

Quoted 3 lines

tc filter add dev eth0 parent 1:0 protocol ip prio 100 u32 match ip src 1.2.3.0/24 classid 1:30

Quoted 7 lines
Quoted 2 lines

tc filter add dev eth1 parent 1:0 protocol ip prio 100 u32 match ip dst 1.2.3.0/24 classid 1:30

I'm pretty sure you want 'flowid 1:30' instead of classid on the filters.

To my knowledge, the classid is declaring the filter to have that class, instead of directing the matching to the class with that id.

Fowid and classid are the same (from f_u32.c) :

     } else if (matches(*argv, "classid") = 0 ||
                    strcmp(*argv, "flowid") = 0) {

Stef

Signature · 7 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.openprojects.net
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
author
#4 lore raw
In reply to Gastón

Hi Stef, this is the output of tc

# tc -s -d class show dev eth1

class htb 1:2 root rate 512Kbit ceil 512Kbit burst 2254b/8 mpu 0b cburst 2254b/8 mpu 0b level 7
Sent 6232181694 bytes 13132747 pkts (dropped 0, overlimits 0) rate 24621bps 60pps
lended: 592516 borrowed: 0 giants: 0
tokens: 17264 ctokens: 17264

class htb 1:57 parent 1:2 leaf 57: prio 0 quantum 3276 rate 128Kbit ceil 128Kbit burst 1762b/8 mpu 0b cburst 1762b/8 mpu 0b level 0
Sent 0 bytes 0 pkts (dropped 0, overlimits 0)
lended: 0 borrowed: 0 giants: 0
tokens: 88149 ctokens: 88149

class htb 1:30 parent 1:2 leaf 30: prio 0 quantum 11468 rate 448Kbit ceil 512Kbit burst 2172b/8 mpu 0b cburst 2254b/8 mpu 0b level 0
Sent 6232147503 bytes 13132747 pkts (dropped 783, overlimits 0) rate 24405bps 60pps
lended: 12540231 borrowed: 592516 giants: 0
tokens: 13875 ctokens: 17264

# tc -s -d filter show dev eth1
filter parent 1: protocol ip pref 100 u32
filter parent 1: protocol ip pref 100 u32 fh 800: ht divisor 1
filter parent 1: protocol ip pref 100 u32 fh 800::800 order 2048 key ht 
800 bkt 0 flowid 1:30
  match c850da00/ffffff00 at 16
filter parent 1: protocol ip pref 100 u32 fh 800::801 order 2049 key ht 
800 bkt 0 flowid 1:57
  match c850da1a/ffffffff at 16
# tc -s -d qdisc show dev eth1
qdisc sfq 57: quantum 1514b limit 128p flows 128/1024 perturb 10sec
 Sent 0 bytes 0 pkts (dropped 0, overlimits 0)

qdisc sfq 30: quantum 1514b limit 128p flows 128/1024 perturb 10sec
Sent 6235399235 bytes 13141249 pkts (dropped 783, overlimits 0)

qdisc htb 1: r2q 5 default 30 direct_packets_stat 1 ver 3.12
Sent 6235399289 bytes 13141250 pkts (dropped 783, overlimits 2438143)

-----Original Message-----
From: Stef Coene <[email protected]>
To: [email protected]
Date: Sat, 6 Mar 2004 13:15:41 +0100
Subject: Re: [LARTC] Limiting bandwidth to entire LAN

Quoted 8 lines · Gastón
Quoted 1 line

Hi, first of all thanks for all your help. I`m using a bridge and I

want to

Quoted 1 line

assign the lan (with public routable ips) only 512Kbits (The internet

link

Quoted 1 line

is 1Mbit). What i thought was creating a class with a ceil of

512Kbit an

Quoted 1 line

applying a filter to it with the entire net (1.2.3.0/24). This

Quoted 17 lines

approach

Quoted 1 line

didn´t work for me(the ceil was bypassed). Should I use policing

instead?
Can you check the counters with tc -s -d class dev eth1 to see if the filters
are working ?

Stef

Signature · 7 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.openprojects.net
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

author
#5 lore raw
In reply to Gastón

Well I´m quite confused about this. I had always shaped on the router (eth0 for outgoing and eth1 for incoming), everything was ok. Now the scenario is different since I want to use a bridge for limiting (not shaping and this is my mistake, I think :)) the 1Mbit connection to 512Kbit for the bridge and the other 512Kbit to go other way (not passing through the bridge). So I think I should do this in a different way, right?
What should I do to acomplish this? Thanks for your help and patience. Cheers.

-----Original Message-----
From: Stef Coene <[email protected]>
To: [email protected]
Date: Sat, 6 Mar 2004 13:15:44 +0100
Subject: Re: [LARTC] Limiting bandwidth to entire LAN

Quoted 14 lines · Damion de Soto
Quoted 3 lines

Hi Gastón,

Quoted 1 line

tc filter add dev eth0 parent 1:0 protocol ip prio 100 u32 match ip

src

Quoted 3 lines
Quoted 3 lines

1.2.3.0/24 classid 1:30

tc filter add dev eth1 parent 1:0 protocol ip prio 100 u32 match ip

dst

Quoted 3 lines
Quoted 1 line

1.2.3.0/24 classid 1:30

I'm pretty sure you want 'flowid 1:30' instead of classid on the

filters.

Quoted 1 line
Quoted 17 lines
Quoted 1 line

To my knowledge, the classid is declaring the filter to have that

class,

Quoted 1 line

instead of directing the matching to the class with that id.

Fowid and classid are the same (from f_u32.c) :

     } else if (matches(*argv, "classid") = 0 ||
                    strcmp(*argv, "flowid") = 0) {

Stef

Signature · 7 lines
[email protected]
 "Using Linux as bandwidth manager"
     http://www.docum.org/
     #lartc @ irc.openprojects.net
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/