Skip to contentSkip to conversation

bridge or vlan

LARTC Vaidas M 3 participants 4 messages Oct 20, 2007 – Oct 22, 2007

lore
Share & tools
lore

Vaidas M

author
#0 lore raw

Hello to everyone,

Here is the situation:

[LAN1]---[eth3]/----------\

               | LinuxBR  |[eth2]---[LAN0]---[linuxGW]---[internet]

[LAN2]---[eth4]\----------/

Whole LAN is in subnet 10.0.0.0/24.

So I need:

LAN0, LAN1, LAN2 could not see each other.

LAN0, LAN1, LAN2 is in same subnet (10.0.0.0/24).

All LANs have to get only internet.

How can I configure LinuxBR to do so?

Do I have to do only bridge? Or only vlan? Or both?

Thanks.

_ _ _ _ _ _ _ __ ___ ____ _____

Vaidas M. [Noxius]

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

#1 lore raw
Quoted 22 lines · On Sat, 20 Oct 2007 14:23:12 +0300 "Vaidas M" <[email protected]> wrote:

Hello to everyone,

Here is the situation:

[LAN1]---[eth3]/----------\

               | LinuxBR  |[eth2]---[LAN0]---[linuxGW]---[internet]

[LAN2]---[eth4]\----------/

Whole LAN is in subnet 10.0.0.0/24.

So I need:

LAN0, LAN1, LAN2 could not see each other.

LAN0, LAN1, LAN2 is in same subnet (10.0.0.0/24).

Quoted 8 lines

All LANs have to get only internet.

How can I configure LinuxBR to do so?

Do I have to do only bridge? Or only vlan? Or both?

On LinuxBR:

	iptables -A FORWARD -s 10.0.0.0/24 -d linuxGW_IP/32 -j ACCEPT
	iptables -A FORWARD -s 10.0.0.0/24 -d 10.0.0.0/24 -j DROP
	iptables -t nat -A POSTROUTING -s 10.0.0.0/24 -d linuxGW_IP/32 -j MASQUERADE

On linuxGW:
iptables -t nat -A POSTROUTING -s LinuxBR_IP/32 -j MASQUERADE

Signature · 5 lines
With best regards, Pan'ko Alexander.
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
#2 lore raw
In reply to Vaidas M
Quoted 12 lines · Vaidas M

Hello to everyone,

Here is the situation:

[LAN1]---[eth3]/----------\
               | LinuxBR  |[eth2]---[LAN0]---[linuxGW]---[internet]

[LAN2]---[eth4]\----------/

Whole LAN is in subnet 10.0.0.0/24.

So I need:

Quoted 8 lines

LAN0, LAN1, LAN2 could not see each other.
LAN0, LAN1, LAN2 is in same subnet (10.0.0.0/24).

All LANs have to get only internet.

How can I configure LinuxBR to do so?

Do I have to do only bridge? Or only vlan? Or both?

This is very simple to do. Bridge all your LANs together (what ever interface you choose to use, physical and / or VLAN) and use EBTables to block forwarding of any traffic that has a source and destination on your 10.0.0.0/24 network. This will allow traffic from the LAN to the world and from the world to the LAN to be bridged, but not allow LAN to LAN traffic to be bridged.

ebtables -t filter -A FORWARD --ip-src 10/24 --ip-dst 10/24 -j DROP

This will block all IP traffic. Broadcasts and ARPs will get through, but can be stopped if you do want. If you do want broadcasts and ARPs to be stopped let me know and I'll propose some follow up rules to add to the above to stop them.

Grant. . . .
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

#3 lore raw
In reply to Vaidas M
Quoted 1 line · Vaidas M

Thanks for your answer, this would help.

You are welcome.

Quoted 2 lines

I think I know how to block arp: -p ARP -j DROP something like that, ant the broadcasts: --pkttype-type ...

Be careful blocking all ARP / broadcasts. Remember that equipment will need to ARP to find the router, at least from the two LANs that are not common with the router.

You will probably want to allow ARPs to the router's IP address (and any other common equipment) and block all others.

Grant. . . .
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc