Skip to contentSkip to conversation

ASoC: Samsung: Updates for v3.8

GIT PULL Padma Venkat 2 participants 2 messages Nov 28, 2012 1 message not in the archive Arm Samsung Exynos

lore
Share & tools
lore
#1 lore raw
In reply to a message not in the archive

Hi Mark,

Quoted 21 lines · Sangbeom Kim
Quoted 14 lines
Quoted 2 lines

There's some problems with this binding. The main one is the gpios property the format of which isn't specified at all.

All of above gpio property is i2s.
That is,

(quoted diff) +7 -0
+     gpios = <&gpz 0 2 0 0>, -> SCLK
+             <&gpz 1 2 0 0>,   ->  CDCLK
+             <&gpz 2 2 0 0>,   -> LRCK
+             <&gpz 3 2 0 0>,   -> SDI
+             <&gpz 4 2 0 0>,   -> SDO[0]
+             <&gpz 5 2 0 0>,   -> SDO[1]
+             <&gpz 6 2 0 0>;   -> SDO[2]

Do you want like a below one?

Review

Quoted 2 lines
(quoted diff) +2 -0
+sclk-gpios = <&gpz 0 2 0 0>,
+cdclk-gpios = <&gpz 1 2 0 0>, ...

That would be nice but what I was really looking for was some indiciation in the binding document as to what all this stuff means - it should really say what gpz is (though I can figure that out) and it definitely needs to say what the four numbers are.

Quoted 6 lines
Quoted 3 lines
Quoted 1 line

The requirement for an alias is also very odd, where does that come from?

I don't know that Which one is odd. Please let me know.

Having them at all is odd - it's not something other DT bindings have needed and there was nothing saying what it was for.

What is the exact requirement here? Should I remove the alias ids or I2S1 and I2S2 nodes as they are in disabled state? This is done same way as SPI and I2C. Please explain me.

Quoted 23 lines
Quoted 22 lines
Quoted 5 lines

Some of the code also looks very peculiar, like the fact that it's generating a clock name i2s_opclk%d rather than hard coding the clock, the physical clock would normally be resolved based on the struct device.

This is to handle all of Samsung SOCs i2c clock mux. Please look at below clk_lookup table

In case of 6410, clk_lookup

(quoted diff) +7 -0
+     CLKDEV_INIT("samsung-i2s.0", "i2s_opclk0", &clk_i2s0),
+     CLKDEV_INIT("samsung-i2s.0", "i2s_opclk1", &clk_audio_bus0.clk),
+     CLKDEV_INIT("samsung-i2s.1", "i2s_opclk0", &clk_i2s1),
+     CLKDEV_INIT("samsung-i2s.1", "i2s_opclk1", &clk_audio_bus1.clk),
+#ifdef CONFIG_CPU_S3C6410
+     CLKDEV_INIT("samsung-i2s.2", "i2s_opclk0", &clk_i2s2),
+     CLKDEV_INIT("samsung-i2s.2", "i2s_opclk1", &clk_audio_bus2.clk),

In case of exynos5, clk_lookup

(quoted diff) +3 -0
+     CLKDEV_INIT("samsung-i2s.0", "i2s_opclk0", &exynos5_clk_sclk_i2s.clk),
+     CLKDEV_INIT("samsung-i2s.0", "i2s_opclk1",
+&exynos5_clk_i2s_bus.clk),
Quoted 7 lines
Quoted 3 lines

We try to handle clock source of i2s by only i2s_opclk0 and i2s_opclk1. Each SOCs have different clock source.
Is this wrong approach?

That makes sense but why is the driver not just requesting by name rather than having code to generate the names, and why is this mixed in with the patch adding DT support?

Thanks
Padma

#2 lore raw
Quoted 4 lines · Padma Venkat
Quoted 1 line · Sangbeom Kim
Quoted 1 line
Quoted 1 line

The requirement for an alias is also very odd, where does that come from?

Quoted 8 lines
Quoted 4 lines
Quoted 1 line

I don't know that Which one is odd. Please let me know.

Having them at all is odd - it's not something other DT bindings have needed and there was nothing saying what it was for.

What is the exact requirement here? Should I remove the alias ids or I2S1 and I2S2 nodes as they are in disabled state? This is done same way as SPI and I2C. Please explain me.

If you need those aliases you need to explain why. They're listed as mandatory so presumably they must be needed for something? It might be that this is a good idea we didn't think of before so the answer is just to document that rather than remove them.