Gianfar : Drop a long frame
Subsystems (2)
Hi Claudiu,
I have a problem with the gianfar driver.
My test conditions are:
- Disable rxvlan hardware acceleration (ethtool -K ethx
rxvlan off)
- Receive frame contains a VLAN tag and with a frame len set
to the MTU (1500 bytes).
In this condition, when I received a long frame the bdp->length is
set to 1538 bytes.
I guess it is composed of:
1500 bytes: L3 data bytes
+ 14 bytes: Ethernet header
+ 4 bytes: Vlan Tag header
+ 8 bytes: FCB structure size GMAC_FCB_LEN
+ 8 bytes: eTSEC padding
+ 4 bytes: Frames CRC (FCS)
The Maximum frame len is set to 1536 because the functiongfar_change_mtu does not integrate the FCS in the computed frame size.
In this condition this frame is dropped with the test line 2792
function gfar_clean_rx_ring
if (unlikely(!(bdp->status & RXBD_ERR) && bdp->length > priv->rx_buffer_size)) bdp->status = RXBD_LARGE; How I can receive this frame correctly? Best regards
Cedric Voncken | R&d Engineer
----------------------------------------------------------------------------
------------------------------
T : +33 1 30 56 46 52
[email protected] | www.acksys.fr
----------------------------------------------------------------------------
------------------------------
ZA Val Joyeux - 10 rue des Entrepreneurs - 78450 VILLEPREUX - France
----------------------------------------------------------------------------
----------
Quoted 32 lines · voncken
Hi Claudiu,
I have a problem with the gianfar driver.
My test conditions are:
- Disable rxvlan hardware acceleration (ethtool -K ethx
rxvlan off)
- Receive frame contains a VLAN tag and with a frame len set
to the MTU (1500 bytes).In this condition, when I received a long frame the bdp->length isset to 1538 bytes.
I guess it is composed of:
1500 bytes: L3 data bytes
+ 14 bytes: Ethernet header
+ 4 bytes: Vlan Tag header
+ 8 bytes: FCB structure sizeGMAC_FCB_LEN
+ 8 bytes: eTSEC padding
+ 4 bytes: Frames CRC (FCS)The Maximum frame len is set to 1536 because the function
gfar_change_mtudoes not integrate the FCS in the computed frame size.
In this condition this frame is dropped with the test line 2792
functiongfar_clean_rx_ringif (unlikely(!(bdp->status & RXBD_ERR) && bdp->length > priv->rx_buffer_size)) bdp->status = RXBD_LARGE; How I can receive this frame correctly? Best regards
Quoted 1 line
Cedric Voncken | R&d Engineer
Hi Cedric Voncken,
Is the 802.1Q support activated on the receiving host? (see CONFIG_VLAN_8021Q)
-----Message d'origine-----
De : Claudiu Manoil [mailto:[email protected]] Envoyé : mercredi 30 janvier 2013 16:56
À : voncken
Cc : [email protected]
Objet : Re: Gianfar : Drop a long frame
Quoted 6 lines · voncken
Hi Claudiu,
I have a problem with the gianfar driver.
My test conditions are:
- Disable rxvlan hardware acceleration (ethtool -K ethx
rxvlan off)
Quoted 1 line
- Receive frame contains a VLAN tag and with a frame len set
to the
Quoted 24 lines
MTU (1500 bytes).
In this condition, when I received a long frame the bdp->length isset to 1538 bytes.
I guess it is composed of:
1500 bytes: L3 data bytes
+ 14 bytes: Ethernet header
+ 4 bytes: Vlan Tag header
+ 8 bytes: FCB structure sizeGMAC_FCB_LEN
+ 8 bytes: eTSEC padding
+ 4 bytes: Frames CRC (FCS)The Maximum frame len is set to 1536 because the function
gfar_change_mtudoes not integrate the FCS in the computed frame size.
In this condition this frame is dropped with the test line 2792
functiongfar_clean_rx_ringif (unlikely(!(bdp->status & RXBD_ERR) && bdp->length > priv->rx_buffer_size)) bdp->status = RXBD_LARGE; How I can receive this frame correctly? Best regards
Quoted 1 line
Cedric Voncken | R&d Engineer
Hi Cedric Voncken,
Is the 802.1Q support activated on the receiving host? (see CONFIG_VLAN_8021Q)
Hi Claudiu,
YEs the CONFIG_VLAN_8021Q is enable on the receiving host, that work correctly if RXVLAN is set to on (ethtool -K ethx rxvlan off) I try with the linux kernel 3.3.8.
Regards.
Quoted 47 lines · voncken
-----Message d'origine-----
De : Claudiu Manoil [mailto:[email protected]] Envoyé : mercredi 30 janvier 2013 16:56
À : voncken
Cc : [email protected]
Objet : Re: Gianfar : Drop a long frameQuoted 6 lines · voncken
Hi Claudiu,
I have a problem with the gianfar driver.
My test conditions are:
- Disable rxvlan hardware acceleration (ethtool -K ethxrxvlan off)
Quoted 1 line
- Receive frame contains a VLAN tag and with a frame len set
to the
Quoted 24 lines
MTU (1500 bytes).
In this condition, when I received a long frame the bdp->length isset to 1538 bytes.
I guess it is composed of:
1500 bytes: L3 data bytes
+ 14 bytes: Ethernet header
+ 4 bytes: Vlan Tag header
+ 8 bytes: FCB structure sizeGMAC_FCB_LEN
+ 8 bytes: eTSEC padding
+ 4 bytes: Frames CRC (FCS)The Maximum frame len is set to 1536 because the function
gfar_change_mtudoes not integrate the FCS in the computed frame size.
In this condition this frame is dropped with the test line 2792
functiongfar_clean_rx_ringif (unlikely(!(bdp->status & RXBD_ERR) && bdp->length > priv->rx_buffer_size)) bdp->status = RXBD_LARGE; How I can receive this frame correctly? Best regardsQuoted 1 line
Cedric Voncken | R&d Engineer
Hi Cedric Voncken,
Is the 802.1Q support activated on the receiving host? (seeCONFIG_VLAN_8021Q)
Quoted 8 lines
Hi Claudiu,
YEs the
CONFIG_VLAN_8021Qis enable on the receiving host, that work correctly if RXVLAN is set to on (ethtool -K ethx rxvlan off) I try with the linux kernel 3.3.8.Regards.
Ok, at fist glance it seems that the DEFAULT_RX_BUFFER_SIZE of 1536
bytes is not enough to accommodate VLAN_HLEN.
Apparently, the reason why it works with rxvlan 'on' and it doesn't
when set to 'off' is because by changing the NETIF_F_HW_VLAN_* feature flags the gfar_change_mtu() gets called, which in turn has the following issue:gfar_change_mtu():
...
if (gfar_is_vlan_on(priv))
frame_size += VLAN_HLEN;
...
where,
gfar_is_vlan_on():
{
return (priv->ndev->features & NETIF_F_HW_VLAN_RX) ||
(priv->ndev->features & NETIF_F_HW_VLAN_TX);
}and it's odd that the rx_buffer_size is conditioned by the HW VLAN acceleration feature being turned on or off. But I'll have to run some tests too to confirm this.
Regards,
Claudiu
Quoted 45 lines · voncken
-----Message d'origine-----
De : Claudiu Manoil [mailto:[email protected]] Envoyé : mercredi 30 janvier 2013 16:56 À : voncken Cc :
[email protected] Objet : Re: Gianfar : Drop a long frameQuoted 6 lines · voncken
Hi Claudiu,
I have a problem with the gianfar driver.
My test conditions are:
- Disable rxvlan hardware acceleration (ethtool -K ethxrxvlan off)
Quoted 1 line
- Receive frame contains a VLAN tag and with a frame len set
to the
Quoted 24 lines
MTU (1500 bytes).
In this condition, when I received a long frame the bdp->length isset to 1538 bytes.
I guess it is composed of:
1500 bytes: L3 data bytes
+ 14 bytes: Ethernet header
+ 4 bytes: Vlan Tag header
+ 8 bytes: FCB structure sizeGMAC_FCB_LEN
+ 8 bytes: eTSEC padding
+ 4 bytes: Frames CRC (FCS)The Maximum frame len is set to 1536 because the function
gfar_change_mtudoes not integrate the FCS in the computed frame size.
In this condition this frame is dropped with the test line 2792
functiongfar_clean_rx_ringif (unlikely(!(bdp->status & RXBD_ERR) && bdp->length > priv->rx_buffer_size)) bdp->status = RXBD_LARGE; How I can receive this frame correctly? Best regardsQuoted 1 line
Cedric Voncken | R&d Engineer
Hi Cedric Voncken,
Is the 802.1Q support activated on the receiving host? (seeCONFIG_VLAN_8021Q)
Quoted 8 lines
Hi Claudiu,
YEs the
CONFIG_VLAN_8021Qis enable on the receiving host, that work correctly if RXVLAN is set to on (ethtool -K ethx rxvlan off) I try with the linux kernel 3.3.8.Regards.
Ok, at fist glance it seems that the DEFAULT_RX_BUFFER_SIZE of 1536 bytes is not enough to accommodate VLAN_HLEN.
Apparently, the reason why it works with rxvlan 'on' and it doesn't when set to 'off' is because by changing the NETIF_F_HW_VLAN_* feature flags the gfar_change_mtu() gets called, which in turn has the following issue:gfar_change_mtu():
...
if (gfar_is_vlan_on(priv))
frame_size += VLAN_HLEN;
...
where,
gfar_is_vlan_on():
{
return (priv->ndev->features & NETIF_F_HW_VLAN_RX) ||
(priv->ndev->features & NETIF_F_HW_VLAN_TX); }and it's odd that the rx_buffer_size is conditioned by the HW VLAN acceleration feature being turned on or off.
But I'll have to run some tests too to confirm this.
Regards,
Claudiu
It's true. That work when rx is on, because the VLAN TAG is removed from frame by eTSEC and the len frame is below 1536.
In the mpc8315 Family reference manual rev 2, the table 19-160 indicates that if L bit is set, the data length includes the CRC. It seems the gfar_change_mtu function must include the CRC length in frame len compute.
Best regards