Asus CUV266-D problems
Okay, I have now upgraded to the 1004 bios version, and reinstalled SuSE linux 7.1 using the minimum install, and added the packages required to compile the kernel.
Unfortunately I still have big problems with booting this computer.
SuSE installer installs 3 kernels:
Linux
Linux 2.4
Suse
All of these use kernel 2.4.0, but with different configurations.
All of these fails during boot, the last message i see is "Starting Syslog", then i get a blank screen and nothing more happens. Only thing that works then is a hard boot.
I managed to boot the 'suse' kernel once, and the attached files are from that session.
The file 'config' is from the 2.4.10 kernel i compiled and tried to boot, but that too
gets the same errors.
It seems to me that it has a lot of problems with the HDD/-controller, as it keeps
complaining about it all the time.
Among others, these are the strangest in my openion:
<4>Warning, log replay starting on readonly filesystem <4>hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } <4>hda: dma_intr: error=0x84 { DriveStatusError BadCRC } <4>hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } <4>hda: dma_intr: error=0x84 { DriveStatusError BadCRC } <4>hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } <4>hda: dma_intr: error=0x84 { DriveStatusError BadCRC } <4>hda: dma_intr: status=0x51 { DriveReady SeekComplete Error } <4>hda: dma_intr: error=0x84 { DriveStatusError BadCRC } <4>ide0: reset timed-out, status=0xd0
I have tried changing the disk, changing cable, tested all HDD-settings (MW, SMART, DMA)
As this is a quite attractive server board, I hope I will get some good help with this problem.
Any additional information needed? Tell me..
-=Dead2=-
----- Original Message -----
From: "Jordan Breeding" <[email protected]>
Quoted 4 lines
Also if you wouldn't mind sending me your
.config from your 2.4.10 kernel I would like to check some options to do with your problem. Thanks.
Quoted 34 lines
Jordan
Quoted 31 lines · Jordan Breeding
P.S. - I didn't see a 1003 version of the -D bios at ftp.asuscom.de but I did see a 1004 version. I also did not see a DLS bios listed at all, this board is hinted at and has basic specs listed at several sites on the internet, does it exist, can it be bought? Thanks for any information that you can give me about the CUV266-DLS. BTW, the unexpected APIC thing is no big deal, it is saying that one of the registers of the APIC stuff is set to something that was unexpected, it happens on almost all current SMP boards I have worked with.Quoted 19 lines · Dead2 wrote:
I'm having big problems with booting on this motherboard.
It is a dual motherboard with 2x Intel P3 866Mhz cpus Asus CUV 266-D Bios rev. 1003
I have tried to boot with the following kernels:
2.4.0 (SuSE 7.1 Install CD)
2.4.4? (SuSE 7.2 Install CD)
2.4.10 Custom compiled with SMP, but no extra ACPI or APM2.4.0 boots and works for a while, but installation always fails.. It just stops, and never gives any error messages.
2.4.4 boots and works for a while, but installation always fails.. It most often stops, but some times it complains about some HDD error (too fast for me to see what it actually says) then reboots.
2.4.10 boots, but only with MPS 1.1, and most of the bios in safety
mode.
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
When it gets to checking the HDD it fails and mounts it read-only.
I can see ACPI errors occuring while booting, but they run along too
fast
Quoted 9 lines
Quoted 9 lines
Quoted 9 lines
for me to fine-read.. (any way to pause/delay it?) Something about unexpected or unknown ACPI-IO *i think*
I have tried to change the HDD with another one, and have confirmed that both are working in another comp. (Western Digital WD200)
If you need any other info, please let me know.
Please give me feedback on what this might be, and how this can be
solved.
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
- Hans K. Rosbach aka Dead2
-
To unsubscribe from this list: send the line "unsubscribe
linux-kernel" in
Quoted 3 lines
Quoted 3 lines
Quoted 3 lines
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/