Skip to contentSkip to conversation

Interlaced mode on intel Clarkdale only colored stripes

DISCUSSION Atechsystem 3 participants 8 messages Feb 13, 2012 1 message not in the archive

lore
Share & tools
lore
#0 lore raw

Hi,

I compiled the kernel from your git repro to test interlaced output with my Clarkdale (H55) Chipset. After installing and reboot I put the interlaced line to my xorg.conf and activate them (first by xorg.conf and after that by lxdm resolution set tool).

I only get a screen full of colored stripes after switching from progressive to interlaced mode. My TV shows 1080i as input mode. After that I read all mode lines from my TV by using the xorg server log and tried every interlaced modeline I found but always the same striped screen. To get sure that I use correct modelines I checked them with an plugged in card from another brand and it works immediately.

Hardware:

- Intel H55 Chipset with Core I5 661 and another one with Core I3
540 CPU

- HDMI and VGA connected to my TV (VGA didn't show any screen with
x and interlaced modes)

- Samsung LE32A557 TV

Software:

- Arch Linux with your kernel 3.3.0 rc1 (compiled yesterday)

- xorg-server 1.11.3-1

- xf86-video-intel 2.17.0-2

@list: Anyone with Clarkdale and running interlaced mode?

Thanks and best regards

Atech

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

#1 lore raw

Hi

2012/2/13 Atechsystem <[email protected]>:

Quoted 2 lines

I compiled the kernel from your git repro to test interlaced output with my Clarkdale (H55) Chipset.

Which git repo and which branch exactly? You may have a repo without the patches that fix interlaced modes.

Quoted 3 lines

After installing and reboot I put the interlaced
line to my xorg.conf and activate them (first by xorg.conf and after that by lxdm resolution set tool).

Which line did you add to xorg.conf? What exactly did you do in this step? Please try to remove every xorg configuration file and test again with the default configuration

Quoted 7 lines

I only get a screen full of colored stripes after switching from progressive to interlaced mode.  My  TV shows 1080i as input mode. After that I read all mode lines from my TV by using the xorg server log and tried every interlaced modeline I found but always the same striped screen. To get sure that I use correct modelines I checked them with an plugged in card from another brand and it works immediately.

Please attach the TV, then run "xrandr --verbose" and send us the output. Please also send the output of intel_reg_dumper:
http://intellinuxgraphics.org/intel_reg_dumper.html

Signature · 1 line
Paulo Zanoni
#2 lore raw

-----Ursprüngliche Nachricht-----
Von: Atechsystem [mailto:[email protected]]
Gesendet: Montag, 13. Februar 2012 19:44
An: 'Paulo Zanoni'
Betreff: AW: [Intel-gfx] Interlaced mode on intel Clarkdale only colored stripes

Hi,

thanks for your quick reply.

Quoted 2 lines

Paulo Zanoni [mailto:[email protected]] Which git repo and which branch exactly? You may have a repo without the patches that fix interlaced

modes.

I compiled it from here: git://people.freedesktop.org/~danvet/drm

Quoted 3 lines

Which line did you add to xorg.conf? What exactly did you do in this step? Please try to remove every xorg configuration file and test again with the default configuration

I added for example:
Modeline "1920x1080@50i" 74.25 1920 2448 2492 2640 1080 1084 1094
1124 interlace +hsync +vsync

Without a modeline I can't select interlace modes. Only 60Hz, 50Hz, 30Hz, 25Hz and 24Hz.

Quoted 1 line

Please attach the TV, then run "xrandr --verbose" and send us the output.

Please also send the output of intel_reg_dumper:

Quoted 1 line

http://intellinuxgraphics.org/intel_reg_dumper.html

Please find files attached.

-----Ursprüngliche Nachricht-----
Von: Paulo Zanoni [mailto:[email protected]]
Gesendet: Montag, 13. Februar 2012 18:58
An: Atechsystem
Cc: [email protected]; [email protected]
Betreff: Re: [Intel-gfx] Interlaced mode on intel Clarkdale only colored stripes

Hi

2012/2/13 Atechsystem <[email protected]>:

Quoted 2 lines

I compiled the kernel from your git repro to test interlaced output with my Clarkdale (H55) Chipset.

Which git repo and which branch exactly? You may have a repo without the patches that fix interlaced modes.

Quoted 3 lines

After installing and reboot I put the interlaced line to my xorg.conf and activate them (first by xorg.conf and after that by lxdm resolution set tool).

Which line did you add to xorg.conf? What exactly did you do in this step? Please try to remove every xorg configuration file and test again with the default configuration

Quoted 7 lines

I only get a screen full of colored stripes after switching from progressive to interlaced mode.  My  TV shows 1080i as input mode. After that I read all mode lines from my TV by using the xorg server log and tried every interlaced modeline I found but always the same striped screen. To get sure that I use correct modelines I checked them with an plugged in card from another brand and it works immediately.

Please attach the TV, then run "xrandr --verbose" and send us the output. Please also send the output of intel_reg_dumper:
http://intellinuxgraphics.org/intel_reg_dumper.html

--
Paulo Zanoni

                    PGETBL_CTL: 0x00000008
               GEN6_INSTDONE_1: 0xfffffffe
               GEN6_INSTDONE_2: 0xffffffff
                  CPU_VGACNTRL: 0x80000000 (disabled)
    DIGITAL_PORT_HOTPLUG_CNTRL: 0x00000000
                     RR_HW_CTL: 0x00000000 (low 0, high 0)
                FDI_PLL_BIOS_0: 0x082b3019
                FDI_PLL_BIOS_1: 0x00000000
                FDI_PLL_BIOS_2: 0x00000000
       DISPLAY_PORT_PLL_BIOS_0: 0x0807012b
       DISPLAY_PORT_PLL_BIOS_1: 0x00000000
       DISPLAY_PORT_PLL_BIOS_2: 0x00000000
              FDI_PLL_FREQ_CTL: 0x00053687
                     PIPEACONF: 0xc0000000 (enabled, active, 8bpc)
                      HTOTAL_A: 0x0897077f (1920 active, 2200 total)
                      HBLANK_A: 0x0897077f (1920 start, 2200 end)
                       HSYNC_A: 0x080307d7 (2008 start, 2052 end)
                      VTOTAL_A: 0x04640437 (1080 active, 1125 total)
                      VBLANK_A: 0x04640437 (1080 start, 1125 end)
                       VSYNC_A: 0x0440043b (1084 start, 1089 end)
                  VSYNCSHIFT_A: 0x00000000
                      PIPEASRC: 0x077f0437 (1920, 1080)
                 PIPEA_DATA_M1: 0x7e3661e0 (TU 64, val 0x3661e0 3564000)
                 PIPEA_DATA_N1: 0x0041eb00 (val 0x41eb00 4320000)
                 PIPEA_DATA_M2: 0x00000000 (TU 1, val 0x0 0)
                 PIPEA_DATA_N2: 0x00000000 (val 0x0 0)
                 PIPEA_LINK_M1: 0x00024414 (val 0x24414 148500)
                 PIPEA_LINK_N1: 0x00041eb0 (val 0x41eb0 270000)
                 PIPEA_LINK_M2: 0x00000000 (val 0x0 0)
                 PIPEA_LINK_N2: 0x00000000 (val 0x0 0)
                      DSPACNTR: 0xd8004000 (enabled)
                      DSPABASE: 0x00000000
                    DSPASTRIDE: 0x00001e00 (120)
                      DSPASURF: 0x00043000
                   DSPATILEOFF: 0x00000000 (0, 0)
                     PIPEBCONF: 0x00000000 (disabled, inactive, 8bpc)
                      HTOTAL_B: 0x031f027f (640 active, 800 total)
                      HBLANK_B: 0x03170287 (648 start, 792 end)
                       HSYNC_B: 0x02ef028f (656 start, 752 end)
                      VTOTAL_B: 0x020c01df (480 active, 525 total)
                      VBLANK_B: 0x020401e7 (488 start, 517 end)
                       VSYNC_B: 0x01eb01e9 (490 start, 492 end)
                  VSYNCSHIFT_B: 0x00000000
                      DSPBCNTR: 0x00000000 (disabled)
                      DSPBBASE: 0x00000000
                    DSPBSTRIDE: 0x00000000 (0)
                      DSPBSURF: 0x00000000
                   DSPBTILEOFF: 0x00000000 (0, 0)
                      PIPEBSRC: 0x027f01df (640, 480)
                 PIPEB_DATA_M1: 0x00000000 (TU 1, val 0x0 0)
                 PIPEB_DATA_N1: 0x00000000 (val 0x0 0)
                 PIPEB_DATA_M2: 0x00000000 (TU 1, val 0x0 0)
                 PIPEB_DATA_N2: 0x00000000 (val 0x0 0)
                 PIPEB_LINK_M1: 0x00000000 (val 0x0 0)
                 PIPEB_LINK_N1: 0x00000000 (val 0x0 0)
                 PIPEB_LINK_M2: 0x00000000 (val 0x0 0)
                 PIPEB_LINK_N2: 0x00000000 (val 0x0 0)
                     PFA_CTL_1: 0x00000000 (disable, auto_scale yes, auto_scale_cal no, v_filter enable, vadapt disable, mode least, filter_sel programmed,chroma pre-filter disable, vert3tap auto, v_inter_invert field 1)
                     PFA_CTL_2: 0x00007de4 (vscale 0.983521)
                     PFA_CTL_3: 0x00003ef2 (vscale initial phase 0.491760)
                     PFA_CTL_4: 0x00007c40 (hscale 0.970703)
                   PFA_WIN_POS: 0x00000000 (0, 0)
                  PFA_WIN_SIZE: 0x00000000 (0, 0)
                     PFB_CTL_1: 0x00000000 (disable, auto_scale yes, auto_scale_cal no, v_filter enable, vadapt disable, mode least, filter_sel programmed,chroma pre-filter disable, vert3tap auto, v_inter_invert field 1)
                     PFB_CTL_2: 0x00000000 (vscale 0.000000)
                     PFB_CTL_3: 0x00000000 (vscale initial phase 0.000000)
                     PFB_CTL_4: 0x00000000 (hscale 0.000000)
                   PFB_WIN_POS: 0x00000000 (0, 0)
                  PFB_WIN_SIZE: 0x00000000 (0, 0)
              PCH_DREF_CONTROL: 0x00000400 (cpu source disable, ssc_source disable, nonspread_source enable, superspread_source disable, ssc4_mode downspread, ssc1 disable, ssc4 disable)
               PCH_RAWCLK_FREQ: 0x0000007d (FDL_TP1 timer 0.5us, FDL_TP2 timer 1.5us, freq 125)
              PCH_DPLL_TMR_CFG: 0x0271186a
                PCH_SSC4_PARMS: 0x00000000
            PCH_SSC4_AUX_PARMS: 0x00000000
                  PCH_DPLL_SEL: 0x00000000 (FDL_TP1 timer 0.5us, FDL_TP2 timer 1.5us, freq 125)
           PCH_DPLL_ANALOG_CTL: 0x00008000
                    PCH_DPLL_A: 0xc4020002 (enable, sdvo high speed yes, mode (null), p2 (null), FPA0 P1 2, FPA1 P1 2, refclk default 120Mhz, sdvo/hdmi mul 1)
                    PCH_DPLL_B: 0x04800080 (disable, sdvo high speed no, mode (null), p2 (null), FPA0 P1 8, FPA1 P1 8, refclk default 120Mhz, sdvo/hdmi mul 1)
                      PCH_FPA0: 0x00021007 (n = 2, m1 = 16, m2 = 7)
                      PCH_FPA1: 0x00021007 (n = 2, m1 = 16, m2 = 7)
                      PCH_FPB0: 0x00030d07 (n = 3, m1 = 13, m2 = 7)
                      PCH_FPB1: 0x00030d07 (n = 3, m1 = 13, m2 = 7)
                TRANS_HTOTAL_A: 0x0897077f (1920 active, 2200 total)
                TRANS_HBLANK_A: 0x0897077f (1920 start, 2200 end)
                 TRANS_HSYNC_A: 0x080307d7 (2008 start, 2052 end)
                TRANS_VTOTAL_A: 0x04640437 (1080 active, 1125 total)
                TRANS_VBLANK_A: 0x04640437 (1080 start, 1125 end)
                 TRANS_VSYNC_A: 0x0440043b (1084 start, 1089 end)
                TRANSA_DATA_M1: 0x00000000 (TU 1, val 0x0 0)
                TRANSA_DATA_N1: 0x00000000 (val 0x0 0)
                TRANSA_DATA_M2: 0x00000000 (TU 1, val 0x0 0)
                TRANSA_DATA_N2: 0x00000000 (val 0x0 0)
             TRANSA_DP_LINK_M1: 0x00000000 (val 0x0 0)
             TRANSA_DP_LINK_N1: 0x00000000 (val 0x0 0)
             TRANSA_DP_LINK_M2: 0x00000000 (val 0x0 0)
             TRANSA_DP_LINK_N2: 0x00000000 (val 0x0 0)
                TRANS_HTOTAL_B: 0x031f027f (640 active, 800 total)
                TRANS_HBLANK_B: 0x03170287 (648 start, 792 end)
                 TRANS_HSYNC_B: 0x02ef028f (656 start, 752 end)
                TRANS_VTOTAL_B: 0x020c01df (480 active, 525 total)
                TRANS_VBLANK_B: 0x020401e7 (488 start, 517 end)
                 TRANS_VSYNC_B: 0x01eb01e9 (490 start, 492 end)
                TRANSB_DATA_M1: 0x00000000 (TU 1, val 0x0 0)
                TRANSB_DATA_N1: 0x00000000 (val 0x0 0)
                TRANSB_DATA_M2: 0x00000000 (TU 1, val 0x0 0)
                TRANSB_DATA_N2: 0x00000000 (val 0x0 0)
             TRANSB_DP_LINK_M1: 0x00000000 (val 0x0 0)
             TRANSB_DP_LINK_N1: 0x00000000 (val 0x0 0)
             TRANSB_DP_LINK_M2: 0x00000000 (val 0x0 0)
             TRANSB_DP_LINK_N2: 0x00000000 (val 0x0 0)
                TRANS_HTOTAL_C: 0x00000000 (1 active, 1 total)
                TRANS_HBLANK_C: 0x00000000 (1 start, 1 end)
                 TRANS_HSYNC_C: 0x00000000 (1 start, 1 end)
                TRANS_VTOTAL_C: 0x00000000 (1 active, 1 total)
                TRANS_VBLANK_C: 0x00000044 (69 start, 1 end)
                 TRANS_VSYNC_C: 0x00000000 (1 start, 1 end)
                TRANSC_DATA_M1: 0x00000000 (TU 1, val 0x0 0)
                TRANSC_DATA_N1: 0x00000000 (val 0x0 0)
                TRANSC_DATA_M2: 0x00000000 (TU 1, val 0x0 0)
                TRANSC_DATA_N2: 0x00000000 (val 0x0 0)
             TRANSC_DP_LINK_M1: 0x00000000 (val 0x0 0)
             TRANSC_DP_LINK_N1: 0x00000000 (val 0x0 0)
             TRANSC_DP_LINK_M2: 0x00000000 (val 0x0 0)
             TRANSC_DP_LINK_N2: 0x00ffffff (val 0xffffff 16777215)
                    TRANSACONF: 0xc0000000 (enable, active)
                    TRANSBCONF: 0x00000000 (disable, inactive)
                    TRANSCCONF: 0x00000000 (disable, inactive)
                   FDI_TXA_CTL: 0xb00c4000 (enable, train pattern not train, voltage swing 0.4V,pre-emphasis none, port width X2, enhanced framing enable, FDI PLL enable, scrambing enable, master mode disable)
                   FDI_TXB_CTL: 0x00044000 (disable, train pattern pattern_1, voltage swing 0.4V,pre-emphasis none, port width X1, enhanced framing enable, FDI PLL enable, scrambing enable, master mode disable)
                   FDI_TXC_CTL: 0x00000000 (disable, train pattern pattern_1, voltage swing 0.4V,pre-emphasis none, port width X1, enhanced framing disable, FDI PLL disable, scrambing enable, master mode disable)
                   FDI_RXA_CTL: 0xb0082050 (enable, train pattern not train, port width X2, 8bpc,link_reverse_strap_overwrite no, dmi_link_reverse no, FDI PLL enable,FS ecc disable, FE ecc disable, FS err report disable, FE err report disable,scrambing enable, enhanced framing enable, PCDClk)
                   FDI_RXB_CTL: 0x00000040 (disable, train pattern pattern_1, port width X1, 8bpc,link_reverse_strap_overwrite no, dmi_link_reverse no, FDI PLL disable,FS ecc disable, FE ecc disable, FS err report disable, FE err report disable,scrambing enable, enhanced framing enable, RawClk)
                   FDI_RXC_CTL: 0x00000000 (disable, train pattern pattern_1, port width X1, 8bpc,link_reverse_strap_overwrite no, dmi_link_reverse no, FDI PLL disable,FS ecc disable, FE ecc disable, FS err report disable, FE err report disable,scrambing enable, enhanced framing disable, RawClk)
                  FDI_RXA_MISC: 0x00000080 (FDI Delay 128)
                  FDI_RXB_MISC: 0x00000080 (FDI Delay 128)
                  FDI_RXC_MISC: 0x00000000 (FDI Delay 0)
               FDI_RXA_TUSIZE1: 0x7e000000
               FDI_RXA_TUSIZE2: 0x7e000000
               FDI_RXB_TUSIZE1: 0x7e000000
               FDI_RXB_TUSIZE2: 0x7e000000
               FDI_RXC_TUSIZE1: 0x00000000
               FDI_RXC_TUSIZE2: 0x00000000
                 FDI_PLL_CTL_1: 0x33505248
                 FDI_PLL_CTL_2: 0x00000000
                   FDI_RXA_IIR: 0x00000000
                   FDI_RXA_IMR: 0x000000ff
                   FDI_RXB_IIR: 0x00000000
                   FDI_RXB_IMR: 0x000000ff
                      PCH_ADPA: 0x00f40018 (disabled, transcoder A, +hsync, +vsync)
                         HDMIB: 0x0000089c (disabled pipe A 8bpc TMDS DVI audio disabled +vsync +hsync detected)
                         HDMIC: 0x8000025c (enabled pipe A 8bpc SDVO HDMI audio enabled +vsync +hsync detected)
                         HDMID: 0x0000001c (disabled pipe A 8bpc SDVO DVI audio disabled +vsync +hsync detected)
                      PCH_LVDS: 0x40000000 (disabled, pipe B, 18 bit, 1 channel)
                     CPU_eDP_A: 0x00000018
                      PCH_DP_B: 0x0000001c
                      PCH_DP_C: 0x0000001c
                      PCH_DP_D: 0x0000001c
                TRANS_DP_CTL_A: 0x00000000 (disabled, pipe B, 18 bit, 1 channel)
                TRANS_DP_CTL_B: 0x00000000 (disabled, pipe B, 18 bit, 1 channel)
                TRANS_DP_CTL_C: 0x00000000 (disabled, pipe B, 18 bit, 1 channel)
              BLC_PWM_CPU_CTL2: 0x00000000
               BLC_PWM_CPU_CTL: 0x00000000
              BLC_PWM_PCH_CTL1: 0x00000000
              BLC_PWM_PCH_CTL2: 0x00000000
                 PCH_PP_STATUS: 0x00000000 (off, not ready, sequencing idle)
                PCH_PP_CONTROL: 0xabcd0000 (blacklight disabled, do not power down on reset, panel off)
              PCH_PP_ON_DELAYS: 0x00000000
             PCH_PP_OFF_DELAYS: 0x00000000
                PCH_PP_DIVISOR: 0x00186904
Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 8192 x 8192
VGA1 disconnected (normal left inverted right x axis y axis)
	Identifier: 0x41
	Timestamp:  135826
	Subpixel:   unknown
	Clones:    
	CRTCs:      0 1
	Transform:  1.000000 0.000000 0.000000
	            0.000000 1.000000 0.000000
	            0.000000 0.000000 1.000000
	           filter: 
HDMI1 disconnected (normal left inverted right x axis y axis)
	Identifier: 0x42
	Timestamp:  135826
	Subpixel:   unknown
	Clones:    
	CRTCs:      0 1
	Transform:  1.000000 0.000000 0.000000
	            0.000000 1.000000 0.000000
	            0.000000 0.000000 1.000000
	           filter: 
	Broadcast RGB:	Full
		supported: Full         Limited 16:2
	audio:	auto
		supported: off          auto         on          
DP1 disconnected (normal left inverted right x axis y axis)
	Identifier: 0x43
	Timestamp:  135826
	Subpixel:   unknown
	Clones:    
	CRTCs:      0 1
	Transform:  1.000000 0.000000 0.000000
	            0.000000 1.000000 0.000000
	            0.000000 0.000000 1.000000
	           filter: 
	Broadcast RGB:	Full
		supported: Full         Limited 16:2
	audio:	auto
		supported: off          auto         on          
HDMI2 connected 1920x1080+0+0 (0x48) normal (normal left inverted right x axis y axis) 160mm x 90mm
	Identifier: 0x44
	Timestamp:  135826
	Subpixel:   unknown
	Gamma:      1.0:1.0:1.0
	Brightness: 1.0
	Clones:    
	CRTC:       0
	CRTCs:      0 1
	Transform:  1.000000 0.000000 0.000000
	            0.000000 1.000000 0.000000
	            0.000000 0.000000 1.000000
	           filter: 
	EDID:
		00ffffffffffff004c2dbc0300000000
		2f110103801009780aee91a3544c9926
		0f50542108008180a940010101010101
		010101010101023a801871382d40582c
		4500a05a0000001e662150b051001b30
		40703600a05a0000001e000000fd0017
		3d1a4c17000a202020202020000000fc
		0053414d53554e470a202020202001d3
		020327f14b901f041305140312202122
		2309070783010000e2000fe305030167
		030c002000b82d011d007251d01e206e
		285500a05a0000001e011d00bc52d01e
		20b8285540a05a0000001e011d801871
		1c1620582c2500a05a0000009e011d80
		d0721c1620102c2580a05a0000009e00
		0000000000000000000000000000000d
	Broadcast RGB:	Full
		supported: Full         Limited 16:2
	audio:	auto
		supported: off          auto         on          
  1920x1080 (0x48)  148.5MHz +HSync +VSync *current +preferred
        h: width  1920 start 2008 end 2052 total 2200 skew    0 clock   67.5KHz
        v: height 1080 start 1084 end 1089 total 1125           clock   60.0Hz
  1920x1080 (0x49)  148.5MHz +HSync +VSync
        h: width  1920 start 2448 end 2492 total 2640 skew    0 clock   56.2KHz
        v: height 1080 start 1084 end 1089 total 1125           clock   50.0Hz
  1920x1080 (0x4a)   74.2MHz +HSync +VSync
        h: width  1920 start 2008 end 2052 total 2200 skew    0 clock   33.8KHz
        v: height 1080 start 1084 end 1089 total 1125           clock   30.0Hz
  1920x1080 (0x4b)   74.2MHz +HSync +VSync
        h: width  1920 start 2448 end 2492 total 2640 skew    0 clock   28.1KHz
        v: height 1080 start 1084 end 1089 total 1125           clock   25.0Hz
  1920x1080 (0x4c)   74.2MHz +HSync +VSync
        h: width  1920 start 2558 end 2602 total 2750 skew    0 clock   27.0KHz
        v: height 1080 start 1084 end 1089 total 1125           clock   24.0Hz
  1600x1200 (0x4d)  162.0MHz +HSync +VSync
        h: width  1600 start 1664 end 1856 total 2160 skew    0 clock   75.0KHz
        v: height 1200 start 1201 end 1204 total 1250           clock   60.0Hz
  1280x1024 (0x4e)  108.0MHz +HSync +VSync
        h: width  1280 start 1328 end 1440 total 1688 skew    0 clock   64.0KHz
        v: height 1024 start 1025 end 1028 total 1066           clock   60.0Hz
  1360x768 (0x4f)   85.5MHz +HSync +VSync
        h: width  1360 start 1424 end 1536 total 1792 skew    0 clock   47.7KHz
        v: height  768 start  771 end  777 total  795           clock   60.0Hz
  1280x720 (0x50)   74.2MHz +HSync +VSync
        h: width  1280 start 1720 end 1760 total 1980 skew    0 clock   37.5KHz
        v: height  720 start  725 end  730 total  750           clock   50.0Hz
  1280x720 (0x51)   74.2MHz +HSync +VSync
        h: width  1280 start 1390 end 1430 total 1650 skew    0 clock   45.0KHz
        v: height  720 start  725 end  730 total  750           clock   60.0Hz
  1024x768 (0x52)   65.0MHz -HSync -VSync
        h: width  1024 start 1048 end 1184 total 1344 skew    0 clock   48.4KHz
        v: height  768 start  771 end  777 total  806           clock   60.0Hz
  800x600 (0x53)   40.0MHz +HSync +VSync
        h: width   800 start  840 end  968 total 1056 skew    0 clock   37.9KHz
        v: height  600 start  601 end  605 total  628           clock   60.3Hz
  720x576 (0x54)   27.0MHz -HSync -VSync
        h: width   720 start  732 end  796 total  864 skew    0 clock   31.2KHz
        v: height  576 start  581 end  586 total  625           clock   50.0Hz
  720x480 (0x55)   27.0MHz -HSync -VSync
        h: width   720 start  736 end  798 total  858 skew    0 clock   31.5KHz
        v: height  480 start  489 end  495 total  525           clock   59.9Hz
  640x480 (0x56)   25.2MHz -HSync -VSync
        h: width   640 start  656 end  752 total  800 skew    0 clock   31.5KHz
        v: height  480 start  490 end  492 total  525           clock   60.0Hz
HDMI3 disconnected (normal left inverted right x axis y axis)
	Identifier: 0x45
	Timestamp:  135826
	Subpixel:   unknown
	Clones:    
	CRTCs:      0 1
	Transform:  1.000000 0.000000 0.000000
	            0.000000 1.000000 0.000000
	            0.000000 0.000000 1.000000
	           filter: 
	Broadcast RGB:	Full
		supported: Full         Limited 16:2
	audio:	auto
		supported: off          auto         on          
DP2 disconnected (normal left inverted right x axis y axis)
	Identifier: 0x46
	Timestamp:  135826
	Subpixel:   unknown
	Clones:    
	CRTCs:      0 1
	Transform:  1.000000 0.000000 0.000000
	            0.000000 1.000000 0.000000
	            0.000000 0.000000 1.000000
	           filter: 
	Broadcast RGB:	Full
		supported: Full         Limited 16:2
	audio:	auto
		supported: off          auto         on          
DP3 disconnected (normal left inverted right x axis y axis)
	Identifier: 0x47
	Timestamp:  135826
	Subpixel:   unknown
	Clones:    
	CRTCs:      0 1
	Transform:  1.000000 0.000000 0.000000
	            0.000000 1.000000 0.000000
	            0.000000 0.000000 1.000000
	           filter: 
	Broadcast RGB:	Full
		supported: Full         Limited 16:2
	audio:	auto
		supported: off          auto         on          

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

#3 lore raw

The git repo is right, but are you sure you are using the remotes/origin/interlaced branch?

It is strange that you couldn't see any interlace mode without using the handmade modeline.

Quoted 81 lines · Atechsystem

-----Ursprüngliche Nachricht-----
Von: Atechsystem [mailto:[email protected]]
Gesendet: Montag, 13. Februar 2012 19:44
An: 'Paulo Zanoni'
Betreff: AW: [Intel-gfx] Interlaced mode on intel Clarkdale only colored stripes

Hi,

thanks for your quick reply.

Quoted 2 lines

Paulo Zanoni [mailto:[email protected]] Which git repo and which branch exactly? You may have a repo without the patches that fix interlaced

modes.

I compiled it from here: git://people.freedesktop.org/~danvet/drm

Quoted 3 lines

Which line did you add to xorg.conf? What exactly did you do in this step? Please try to remove every xorg configuration file and test again with the default configuration

I added for example:
Modeline    "1920x1080@50i"     74.25 1920 2448 2492 2640 1080 1084 1094 1124 interlace +hsync +vsync

Without a modeline I can't select interlace modes. Only 60Hz, 50Hz, 30Hz, 25Hz and 24Hz.

Quoted 1 line

Please attach the TV, then run "xrandr --verbose" and send us the output.

Please also send the output of intel_reg_dumper:

Quoted 1 line

http://intellinuxgraphics.org/intel_reg_dumper.html

Please find files attached.

-----Ursprüngliche Nachricht-----
Von: Paulo Zanoni [mailto:[email protected]]
Gesendet: Montag, 13. Februar 2012 18:58
An: Atechsystem
Cc: [email protected]; [email protected]
Betreff: Re: [Intel-gfx] Interlaced mode on intel Clarkdale only colored stripes

Hi

2012/2/13 Atechsystem <[email protected]>:

Quoted 2 lines

I compiled the kernel from your git repro to test interlaced output with my Clarkdale (H55) Chipset.

Which git repo and which branch exactly? You may have a repo without the patches that fix interlaced modes.

Quoted 3 lines

After installing and reboot I put the interlaced line to my xorg.conf and activate them (first by xorg.conf and after that by lxdm resolution set tool).

Which line did you add to xorg.conf? What exactly did you do in this step? Please try to remove every xorg configuration file and test again with the default configuration

Quoted 7 lines

I only get a screen full of colored stripes after switching from progressive to interlaced mode.  My  TV shows 1080i as input mode. After that I read all mode lines from my TV by using the xorg server log and tried every interlaced modeline I found but always the same striped screen. To get sure that I use correct modelines I checked them with an plugged in card from another brand and it works immediately.

Please attach the TV, then run "xrandr --verbose" and send us the output. Please also send the output of intel_reg_dumper:
http://intellinuxgraphics.org/intel_reg_dumper.html

--
Paulo Zanoni

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

Signature · 3 lines
Rodrigo Vivi
Blog: http://blog.vivi.eng.br
GPG: 0x905BE242 @ wwwkeys.pgp.net

A message that is not in the archive (sent off-list or not yet received): [email protected]

#5 lore raw

2012/2/13 Atechsystem <[email protected]>:

Quoted 1 line

I compiled it from here: git://people.freedesktop.org/~danvet/drm

Did you change to the "interlaced" branch?

Maybe the best tree to test is this:
http://cgit.freedesktop.org/~danvet/drm-intel/log/?h=drm-intel-next-queued

(repository is drm-intel and branch is drm-intel-next-queued).

Quoted 6 lines

I added for example:
Modeline    "1920x1080@50i"     74.25 1920 2448 2492 2640 1080 1084 1094 1124 interlace +hsync +vsync

Without a modeline I can't select interlace modes. Only 60Hz, 50Hz, 30Hz, 25Hz and 24Hz.

This should not be needed. If you have the correct branch, you don't need any configuration tweak: just boot the machine, plug a monitor that supports interlaced modes, and "xrandr --verbose" will show you some interlaced modes.

Please confirm that you are using the correct branch first. Use "git log" or "git branch" commands to check.

Signature · 1 line
Paulo Zanoni
#6 lore raw
Quoted 3 lines

Von: Paulo Zanoni [mailto:[email protected]]
Maybe the best tree to test is this:
http://cgit.freedesktop.org/~danvet/drm-intel/log/?h=drm-intel-next-queued

I will compile it now. Before I used the drm-intel-next branch. I downloaded the latest tar.gz file and didn't use git to checkout the branch.

Quoted 2 lines

Rodrigo Vivi [mailto:[email protected]]
The git repo is right, but are you sure you are using the

remotes/origin/interlaced branch?

Quoted 1 line

It is strange that you couldn't see any interlace mode without using the

handmade modeline.

No chance to select it directly. I 've no clue to select it by standard lxde dialog.

-----Ursprüngliche Nachricht-----
Von: Paulo Zanoni [mailto:[email protected]]
Gesendet: Montag, 13. Februar 2012 19:56
An: Atechsystem
Cc: Intel Graphics Development
Betreff: Re: [Intel-gfx] Interlaced mode on intel Clarkdale only colored stripes

2012/2/13 Atechsystem <[email protected]>:

Quoted 1 line

I compiled it from here: git://people.freedesktop.org/~danvet/drm

Did you change to the "interlaced" branch?

Maybe the best tree to test is this:
http://cgit.freedesktop.org/~danvet/drm-intel/log/?h=drm-intel-next-queued

(repository is drm-intel and branch is drm-intel-next-queued).

Quoted 7 lines

I added for example:
Modeline    "1920x1080@50i"     74.25 1920 2448 2492 2640 1080 1084 1094
1124 interlace +hsync +vsync

Without a modeline I can't select interlace modes. Only 60Hz, 50Hz, 30Hz, 25Hz and 24Hz.

This should not be needed. If you have the correct branch, you don't need any configuration tweak: just boot the machine, plug a monitor that supports interlaced modes, and "xrandr --verbose" will show you some interlaced modes.

Please confirm that you are using the correct branch first. Use "git log" or "git branch" commands to check.

--
Paulo Zanoni

#7 lore raw

Hello,

Quoted 3 lines

Von: Paulo Zanoni [mailto:[email protected]] Maybe the best tree to test is this:
http://cgit.freedesktop.org/~danvet/drm-intel/log/?h=drm-intel-next-queued

Thanks, compiling from this repro solved my problem. With my TV I have to use the xorg modeline, without it I can't select the interlaced modes. If I use my NEC monitor I can select the I modeline by using the lxde monitor setting tool. I think my TV don't report the I modelines.

Thanks for this patch

Regards
Atech

-----Ursprüngliche Nachricht-----
Von: [email protected] [mailto:[email protected]] Im Auftrag von Atechsystem
Gesendet: Montag, 13. Februar 2012 20:05
An: 'Paulo Zanoni'
Cc: [email protected]
Betreff: Re: [Intel-gfx] Interlaced mode on intel Clarkdale only colored stripes

Quoted 4 lines

Von: Paulo Zanoni [mailto:[email protected]] Maybe the best tree to test is this:
http://cgit.freedesktop.org/~danvet/drm-intel/log/?h=drm-intel-next-que
ued

I will compile it now. Before I used the drm-intel-next branch. I downloaded the latest tar.gz file and didn't use git to checkout the branch.

Quoted 2 lines

Rodrigo Vivi [mailto:[email protected]] The git repo is right, but are you sure you are using the

remotes/origin/interlaced branch?

Quoted 2 lines

It is strange that you couldn't see any interlace mode without using the

handmade modeline.

No chance to select it directly. I 've no clue to select it by standard lxde dialog.

-----Ursprüngliche Nachricht-----
Von: Paulo Zanoni [mailto:[email protected]]
Gesendet: Montag, 13. Februar 2012 19:56
An: Atechsystem
Cc: Intel Graphics Development
Betreff: Re: [Intel-gfx] Interlaced mode on intel Clarkdale only colored stripes

2012/2/13 Atechsystem <[email protected]>:

Quoted 1 line

I compiled it from here: git://people.freedesktop.org/~danvet/drm

Did you change to the "interlaced" branch?

Maybe the best tree to test is this:
http://cgit.freedesktop.org/~danvet/drm-intel/log/?h=drm-intel-next-queued

(repository is drm-intel and branch is drm-intel-next-queued).

Quoted 7 lines

I added for example:
Modeline    "1920x1080@50i"     74.25 1920 2448 2492 2640 1080 1084 1094
1124 interlace +hsync +vsync

Without a modeline I can't select interlace modes. Only 60Hz, 50Hz, 30Hz, 25Hz and 24Hz.

This should not be needed. If you have the correct branch, you don't need any configuration tweak: just boot the machine, plug a monitor that supports interlaced modes, and "xrandr --verbose" will show you some interlaced modes.

Please confirm that you are using the correct branch first. Use "git log" or "git branch" commands to check.

--
Paulo Zanoni

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

#8 lore raw

I'm glad that it is working for you now!

Yes, the drm-intel-next-queued has all the interlaced patches that were in remotes/origin/interlaced. I don't think your tv doesn't report the interlaced modes, but the modes it reports are the CEA modes we aren't supporting yet. It is on my todo list take a carefully look at this modes.

Cheers,
Rodrigo.

Quoted 92 lines · Atechsystem

Hello,

Quoted 3 lines

Von: Paulo Zanoni [mailto:[email protected]] Maybe the best tree to test is this:
http://cgit.freedesktop.org/~danvet/drm-intel/log/?h=drm-intel-next-queued

Thanks, compiling from this repro solved my problem. With my TV I have to use the xorg modeline, without it I can't select the interlaced modes. If I use my NEC monitor I can select the I modeline by using the lxde monitor setting tool. I think my TV don't report the I modelines.

Thanks for this patch

Regards
Atech

-----Ursprüngliche Nachricht-----
Von: [email protected] [mailto:[email protected]] Im Auftrag von Atechsystem
Gesendet: Montag, 13. Februar 2012 20:05
An: 'Paulo Zanoni'
Cc: [email protected]
Betreff: Re: [Intel-gfx] Interlaced mode on intel Clarkdale only colored stripes

Quoted 4 lines

Von: Paulo Zanoni [mailto:[email protected]] Maybe the best tree to test is this:
http://cgit.freedesktop.org/~danvet/drm-intel/log/?h=drm-intel-next-que
ued

I will compile it now. Before I used the drm-intel-next branch. I downloaded the latest tar.gz file and didn't use git to checkout the branch.

Quoted 2 lines

Rodrigo Vivi [mailto:[email protected]] The git repo is right, but are you sure you are using the

remotes/origin/interlaced branch?

Quoted 2 lines

It is strange that you couldn't see any interlace mode without using the

handmade modeline.

No chance to select it directly. I 've no clue to select it by standard lxde dialog.

-----Ursprüngliche Nachricht-----
Von: Paulo Zanoni [mailto:[email protected]]
Gesendet: Montag, 13. Februar 2012 19:56
An: Atechsystem
Cc: Intel Graphics Development
Betreff: Re: [Intel-gfx] Interlaced mode on intel Clarkdale only colored stripes

2012/2/13 Atechsystem <[email protected]>:

Quoted 1 line

I compiled it from here: git://people.freedesktop.org/~danvet/drm

Did you change to the "interlaced" branch?

Maybe the best tree to test is this:
http://cgit.freedesktop.org/~danvet/drm-intel/log/?h=drm-intel-next-queued

(repository is drm-intel and branch is drm-intel-next-queued).

Quoted 7 lines

I added for example:
Modeline    "1920x1080@50i"     74.25 1920 2448 2492 2640 1080 1084 1094
1124 interlace +hsync +vsync

Without a modeline I can't select interlace modes. Only 60Hz, 50Hz, 30Hz, 25Hz and 24Hz.

This should not be needed. If you have the correct branch, you don't need any configuration tweak: just boot the machine, plug a monitor that supports interlaced modes, and "xrandr --verbose" will show you some interlaced modes.

Please confirm that you are using the correct branch first. Use "git log" or "git branch" commands to check.

--
Paulo Zanoni

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx

Signature · 3 lines
Rodrigo Vivi
Blog: http://blog.vivi.eng.br
GPG: 0x905BE242 @ wwwkeys.pgp.net