Asus CUV266-D problems
I'm having big problems with booting on this motherboard.
It is a dual motherboard with 2x Intel P3 866Mhz cpus Asus CUV 266-D Bios rev. 1003
I have tried to boot with the following kernels:
2.4.0 (SuSE 7.1 Install CD)
2.4.4? (SuSE 7.2 Install CD)
2.4.10 Custom compiled with SMP, but no extra ACPI or APM
2.4.0 boots and works for a while, but installation always fails.. It just stops, and never gives any error messages.
2.4.4 boots and works for a while, but installation always fails.. It most often stops, but some times it complains about some HDD error (too fast for me to see what it actually says) then reboots.
2.4.10 boots, but only with MPS 1.1, and most of the bios in safety mode. When it gets to checking the HDD it fails and mounts it read-only.
I can see ACPI errors occuring while booting, but they run along too fast for me to fine-read.. (any way to pause/delay it?)
Something about unexpected or unknown ACPI-IO *i think*
I have tried to change the HDD with another one, and have confirmed that both are working in another comp. (Western Digital WD200)
I'll type _some_ of what lspci outputs, please forgive any spellings and shorts:
00:00.0 Host bridge: VIA Tech, Inc. VT8633 [Apollo Pro266] (rev 01)
subsystem: Asustek Computer, Inc.: Unknown device 8064
Flags: bus master, medium devsel, latency 0 Memory at fe000000 (32-bit, prefetch) [size=8M]
Capabilities: [a0] AGP version 2.0
Capabilities: [c0] Power Management ver. 2
00:01.0 PCI bridge: VIA Tech, Inc. VT8633 [Apollo Pro266 AGP] (prog-if 00 [normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: f6000000-f7efffff Prefetchable memory behind bridge: fbf00000-fdffffff
Capabilities: [80] Power management ver. 2
00:11.0 ISA bridge: VIA Tech, Inc. VT8233 PCI to ISA Bridge
subsystem: Asustek Computer, Inc.: Unknown device 8052
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: [c0] Power Management ver. 2
00:11.1 IDE interface: VIA Tech, Inc. Bus Master IDE (rev 06)
Flags: bus master, stepping, medium devsel, latency 32 I/O ports at a800 [size=16]
Capabilities: [c0] Power Management ver. 2
In addition these are listed, please ask me if you need more details:
00:0e.0 PCI bridge: Digital Equip. Corp. DECchip 21152 (rev 03) 00:10.0 PCI bridge: Digital Equip. Corp. DECchip 21152 (rev 03) 01:00.0 VGA compat. contr.: nVidia Corp. Vanta [NV6] (rev 15) 02:04.0 Ethernet Controller: Intel Corp. 82557 [Ethernet Pro 100] (rev 05) 02:05.0 Ethernet Controller: Intel Corp. 82557 [Ethernet Pro 100] (rev 05) 03:04.0 Ethernet Controller: Intel Corp. 82557 [Ethernet Pro 100] (rev 05) 03:05.0 Ethernet Controller: Intel Corp. 82557 [Ethernet Pro 100] (rev 05)
There are two Intel Dual server NIC's in the box.. meaning each card has 1x DEC21152, and 2x Intel82557 on them.
If you need any other info, please let me know.
Please give me feedback on what this might be, and how this can be solved.
- Hans K. Rosbach aka Dead2
The CUV266-D is indeed in wide production, and i bought it from www.komplett.no Unfortunately that site is here in Norway. I am sure several international sites sell it aswell.
http://www.komplett.no/k/k.asp?action=info&p=15140&l=2&AvdID=1&CatID=10&GrpI
D=6&s=pl
The CUV266-DLS is also available from that page, and they even have them in stock..
http://www.komplett.no/k/k.asp?action=info&p=16520&l=2&AvdID=1&CatID=10&GrpI
D=6&s=pl
When I'm looking at the lspci -v output, i keep wondering why two of the chips read "Unknown device 8064".. Shouldn't this be fixed by a kernel maintainer?
I'll send you the .config tomorrow, and I'll test the 1004 bios version then too, as i'm not at work today.. =/
- Hans K. aka Dead2
----- Original Message -----
From: "Jordan Breeding" <[email protected]>
Quoted 31 lines
Sorry to bother you again so quickly, do you know if this board is in wide production yet, specifically the CUV266-DLS? Did you have to buy yours or did you get a testing copy, if you had to buy yours do you mind my asking where you got it? Also if you wouldn't mind sending me your .config from your 2.4.10 kernel I would like to check some options to do with your problem. Thanks.
Jordan
Quoted 21 lines · Jordan Breeding
Sorry I can't provide any help about the CUV266-D, however I have been waiting for some time for this board to come out. I have a Tyan Tiger 230 currently but wanted a 266 chipset and also onboard scsi. I didn't really feel completely comfortable with the LSI chipset on the CUV4X-DLS, so I was very glad to hear that the DLS version of the CUV266 is supposed to have an Adaptec SCSI chipset. Do you know where I can find any further information on either of the boards, the CUV266-D or the DLS, also where are they available to be bought?
Jordan
P.S. - I didn't see a 1003 version of the -D bios at ftp.asuscom.de but I did see a 1004 version. I also did not see a DLS bios listed at all, this board is hinted at and has basic specs listed at several sites on the internet, does it exist, can it be bought? Thanks for any information that you can give me about the CUV266-DLS. BTW, the unexpected APIC thing is no big deal, it is saying that one of the registers of the APIC stuff is set to something that was unexpected, it happens on almost all current SMP boards I have worked with.