Skip to contentSkip to conversation

IDE bug in 2.4.2-ac12?

DISCUSSION Konrad Stopsack 4 participants 6 messages Mar 6, 2001 – Mar 8, 2001

lore
Share & tools
lore
#0 lore raw

Hello guys,

I hope you've read my posting "DMA problem with ZIP drive and VIA VT82C598MVP / VT82C586B chip" (why does anybody answer?).
I now tried the 2.4.2-ac12 kernel including the latest VIA 82c586b driver (version 3.21), but the effects were almost the same:
- just when the kernel tried to access to the hard disk during boot, DMA errors were occured
- "hdparm /dev/hda" displayed 9 MB per second (and not 11 MB like without ZIP)
- /proc/ide/via reported 16 MB transfer rate (and not 33MB like without ZIP drive)
- Kernel 2.4.2-ac12 reports a "ide-floppy: hdd: I/O error, pc = 5a, key = 5, asc = 24, ascq = 0" error, 2.4.2 doesn't

My IDE configuration is:
/dev/hda: Hard disk => Primary IDE controller
/dev/hdc CD-ROM => Secondary IDE controller
/dev/hdd: ZIP => Secondary IDE controller

Could you please tell me whether it's a bug or a feature?
I'm really waiting for your answer - else I might get crazy with this problem :-((

I attached both dmesg and /proc/ide/via, and my old posting.

cu Konrad

boot messages of 2.4.2-ac12:
Linux version 2.4.2-ac12 (root@Stopsack) (gcc version 2.95.2 19991024 (release)) #5 Tue Mar 6 17:25:57 CET 2001
BIOS-provided physical RAM map:
BIOS-e820: 00000000000a0000 @ 0000000000000000 (usable)
BIOS-e820: 0000000000010000 @ 00000000000f0000 (reserved)
BIOS-e820: 0000000013f00000 @ 0000000000100000 (usable)
BIOS-e820: 0000000000010000 @ 00000000ffff0000 (reserved)
On node 0 totalpages: 81920
zone(0): 4096 pages.
zone(1): 77824 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=ac24 ro root=304 1
Initializing CPU#0
Detected 350.802 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 699.59 BogoMIPS
Memory: 320240k/327680k available (934k kernel code, 7056k reserved, 266k data, 176k init, 0k highmem)
Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes) Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes) Page-cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
CPU: Before vendor init, caps: 008021bf 808029bf 00000000, vendor = 2
CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line)
CPU: After vendor init, caps: 008021bf 808029bf 00000000 00000002
CPU: After generic, caps: 008021bf 808029bf 00000000 00000002
CPU: Common caps: 008021bf 808029bf 00000000 00000002
CPU: AMD-K6(tm) 3D processor stepping 0c
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfb3f0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router VIA [1106/0586] at 00:07.0
Activating ISA DMA hang workarounds.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039 Starting kswapd v1.8
parport0: PC-style at 0x378 [PCSPP(,...)]
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
lp0: using parport0 (polling).
block: queued sectors max/low 212464kB/81392kB, 640 slots per queue Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c586b (rev 47) IDE UDMA33 controller on pci00:07.1

    ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA

hda: Maxtor 91080D5, ATA DISK drive
hdc: ASUS CD-S400/A, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 21095424 sectors (10801 MB) w/512KiB Cache, CHS=1313/255/63, UDMA(33)
hdc: ATAPI 40X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
hdd: 98304kB, 96/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm
ide-floppy: hdd: I/O error, pc = 5a, key = 5, asc = 24, ascq = 0 Partition check:
hda: hda1 hda2 hda3 hda4
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS01 at 0x02f8 (irq = 3) is a 16550A
PPP generic driver version 2.4.1
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 263M
agpgart: Detected Via MVP3 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
fatfs: bogus cluster size
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide0: reset: success
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
reiserfs: checking transaction log (device 03:04) ...
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
Using tea hash to sort names
reiserfs: using 3.5.x disk format
ReiserFS version 3.6.25
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 176k freed
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide0: reset: success
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide0: reset: success
Adding Swap: 104416k swap-space (priority -1)

boot messages of 2.4.2:
Linux version 2.4.2 (root@Stopsack) (gcc version 2.95.2 19991024 (release)) #4 Sun Feb 25 11:15:33 CET 2001
BIOS-provided physical RAM map:
BIOS-e820: 000000000009fc00 @ 0000000000000000 (usable)
BIOS-e820: 0000000000000400 @ 000000000009fc00 (usable)
BIOS-e820: 0000000000010000 @ 00000000000f0000 (reserved)
BIOS-e820: 0000000000010000 @ 00000000ffff0000 (reserved)
BIOS-e820: 0000000013f00000 @ 0000000000100000 (usable)
On node 0 totalpages: 81920
zone(0): 4096 pages.
zone(1): 77824 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=lx24 ro root=304 1
Initializing CPU#0
Detected 350.802 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 699.59 BogoMIPS
Memory: 320180k/327680k available (927k kernel code, 7112k reserved, 335k data, 176k init, 0k highmem)
Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes) Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes) Page-cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
CPU: Before vendor init, caps: 008021bf 808029bf 00000000, vendor = 2
CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line)
CPU: After vendor init, caps: 008021bf 808029bf 00000000 00000002
CPU: After generic, caps: 008021bf 808029bf 00000000 00000002
CPU: Common caps: 008021bf 808029bf 00000000 00000002
CPU: AMD-K6(tm) 3D processor stepping 0c
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfb3f0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router VIA [1106/0586] at 00:07.0
Activating ISA DMA hang workarounds.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039 Starting kswapd v1.8
parport0: PC-style at 0x378 [PCSPP(,...)]
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
lp0: using parport0 (polling).
block: queued sectors max/low 212421kB/81349kB, 640 slots per queue
loop: enabling 8 loop devices
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c586b (rev 47) IDE UDMA33 controller on pci00:07.1

    ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA

hda: Maxtor 91080D5, ATA DISK drive
hdc: ASUS CD-S400/A, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 21095424 sectors (10801 MB) w/512KiB Cache, CHS=1313/255/63, UDMA(33)
hdc: ATAPI 40X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
hdd: 98304kB, 196608 blocks, 512 sector size, , DMA
hdd: 98304kB, 96/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm Partition check:
hda: hda1 hda2 hda3 hda4
hdd: hdd4
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS01 at 0x02f8 (irq = 3) is a 16550A
PPP generic driver version 2.4.1
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 263M
agpgart: Detected Via MVP3 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
fatfs: bogus cluster size
reiserfs: checking transaction log (device 03:04) ...
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
Using tea hash to sort names
reiserfs: using 3.5.x disk format
ReiserFS version 3.6.25
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 176k freed
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide0: reset: success
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide0: reset: success
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide0: reset: success
Adding Swap: 104416k swap-space (priority -1)
VFS: Disk change detected on device ide1(22,68)
hdd: hdd4
VFS: Disk change detected on device ide1(22,68)
hdd: hdd4

2.4.2-ac12's /proc/ide/via:
----------VIA BusMastering IDE Configuration----------------

Driver Version:                     3.21
South Bridge:                       VIA vt82c586b
Revision:                           ISA 0x47 IDE 0x6
Highest DMA rate:                   UDMA33
BM-DMA base:                        0xe000
PCI clock:                          33MHz
Master Read  Cycle IRDY:            1ws
Master Write Cycle IRDY:            1ws
BM IDE Status Register Read Retry:  yes
Max DRDY Pulse Width:               No limit
-----------------------Primary IDE-------Secondary IDE------
Read DMA FIFO flush:          yes                 yes
End Sector FIFO flush:         no                  no
Prefetch Buffer:              yes                 yes
Post Write Buffer:            yes                  no
Enabled:                      yes                 yes
Simplex only:                  no                  no
Cable Type:                   40w                 40w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode:        DMA       DMA      UDMA       DMA
Address Setup:       30ns     120ns      30ns      60ns
Cmd Active:          90ns      90ns      90ns      90ns
Cmd Recovery:        30ns      30ns      90ns      90ns
Data Active:         90ns     330ns      90ns      90ns
Data Recovery:       30ns     270ns      30ns      90ns
Cycle Time:         120ns     600ns      60ns     180ns
Transfer Rate:   16.5MB/s   3.3MB/s  33.0MB/s  11.0MB/s

2.4.2's /proc/ide/via:
----------VIA BusMastering IDE Configuration----------------

Driver Version:                     3.20
South Bridge:                       VIA vt82c586b
Revision:                           ISA 0x47 IDE 0x6
BM-DMA base:                        0xe000
PCI clock:                          33MHz
Master Read  Cycle IRDY:            1ws
Master Write Cycle IRDY:            1ws
BM IDE Status Register Read Retry:  yes
Max DRDY Pulse Width:               No limit
-----------------------Primary IDE-------Secondary IDE------
Read DMA FIFO flush:          yes                 yes
End Sector FIFO flush:         no                  no
Prefetch Buffer:              yes                 yes
Post Write Buffer:            yes                  no
Enabled:                      yes                 yes
Simplex only:                  no                  no
Cable Type:                   40w                 40w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode:        DMA       DMA      UDMA       DMA
Address Setup:       30ns     120ns      30ns      60ns
Cmd Active:          90ns      90ns      90ns      90ns
Cmd Recovery:        30ns      30ns      90ns      90ns
Data Active:         90ns     330ns      90ns      90ns
Data Recovery:       30ns     270ns      30ns      90ns
Cycle Time:         120ns     600ns      60ns     180ns
Transfer Rate:   16.5MB/s   3.3MB/s  33.0MB/s  11.0MB/s

My old posting:

Quoted 6 lines

Hello guys (especially Vojtech),

I've got a strange problem with my ZIP drive. If I connect it as /dev/hdd, I'm not able to use uDMA on my hard disk (/dev/hda) properly anymore. Once the kernel stopped with a "kernel panic" (because an disk I/O error occured and ReiserFS coudn't read a superblock, so Linux wasn't able to >

mount

Quoted 23 lines

the root FS). Next time I tried to boot it, lots of DMA errors occured, but the system booted. Unfortunally the disk transfer rate was 9MB/s and not 11 anymore...

Kernel: 2.4.2 (with VIA support enabled, but no "use DMA when available")
Chip: VT82C598MVP / VT82C586B
ZIP: Iomega ZIP 100MB drive
Hard disk: Maxtor 91080D5 (10GB)
CD-ROM: Asus CD-S400/A (/dev/hdc)

lspci output:
00:00.0 Host bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3] (rev 04)
Flags: bus master, medium devsel, latency 16
Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0

00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3 AGP] (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: e4000000-e7ffffff Prefetchable memory behind bridge: e8000000-e8ffffff

Quoted 6 lines

00:07.0 ISA bridge: VIA Technologies, Inc. VT82C586/A/B PCI-to-ISA [Apollo VP] (rev 47)
Subsystem: VIA Technologies, Inc. MVP3 ISA Bridge
Flags: bus master, stepping, medium devsel, latency 0

00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev >

06)

Quoted 35 lines

(prog-if 8a [Master SecP PriP])
Flags: bus master, medium devsel, latency 32 I/O ports at e000 [size=16]

00:07.2 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 02) (prog-if 00 [UHCI])

        Subsystem: Unknown device 0925:1234
        Flags: bus master, medium devsel, latency 32, IRQ 12
        I/O ports at e400 [size=32]

00:07.3 Host bridge: VIA Technologies, Inc. VT82C586B ACPI (rev 10)
Flags: medium devsel

00:09.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 08)
Subsystem: Ensoniq: Unknown device 1371
Flags: bus master, slow devsel, latency 32, IRQ 5
I/O ports at e800 [size=64]
Capabilities: [dc] Power Management version 1

01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200 AGP (rev
03) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G200 SD AGP
Flags: bus master, medium devsel, latency 32, IRQ 11 Memory at e8000000 (32-bit, prefetchable) [size=16M] Memory at e4000000 (32-bit, non-prefetchable) [size=16K] Memory at e5000000 (32-bit, non-prefetchable) [size=8M] Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 1
Capabilities: [f0] AGP version 1.0

hdparm -i:

/dev/hda:

Quoted 10 lines

Model=Maxtor 91080D5, FwRev=GAS54112, SerialNo=A50BDR4C Config={ Fixed }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=29 BuffType=3(DualPortCache), BuffSize=512kB, MaxMultSect=16, MultSect=off DblWordIO=no, OldPIO=2, DMA=yes, OldDMA=2 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=21095424 tDMA={min:120,rec:120}, DMA modes: mword0 mword1 *mword2 IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4 UDMA modes: mode0 mode1 mode2
Drive Supports : ATA/ATAPI-4 T13 1153D revision 17 : ATA-1 ATA-2 ATA-3

ATA-4

Quoted 63 lines

hdparm | grep version:
hdparm version: 3.6

dmesg:

Linux version 2.4.2 (root@Stopsack) (gcc version 2.95.2 19991024 (release)) #4 Sun Feb 25 11:15:33 CET 2001
BIOS-provided physical RAM map:
BIOS-e820: 000000000009fc00 @ 0000000000000000 (usable)
BIOS-e820: 0000000000000400 @ 000000000009fc00 (usable)
BIOS-e820: 0000000000010000 @ 00000000000f0000 (reserved)
BIOS-e820: 0000000000010000 @ 00000000ffff0000 (reserved)
BIOS-e820: 0000000013f00000 @ 0000000000100000 (usable)
On node 0 totalpages: 81920
zone(0): 4096 pages.
zone(1): 77824 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=lx24 ro root=304 1
Initializing CPU#0
Detected 350.802 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 699.59 BogoMIPS
Memory: 320180k/327680k available (927k kernel code, 7112k reserved, 335k data, 176k init, 0k highmem)
Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes) Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes) Page-cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
CPU: Before vendor init, caps: 008021bf 808029bf 00000000, vendor = 2
CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line)
CPU: After vendor init, caps: 008021bf 808029bf 00000000 00000002
CPU: After generic, caps: 008021bf 808029bf 00000000 00000002
CPU: Common caps: 008021bf 808029bf 00000000 00000002
CPU: AMD-K6(tm) 3D processor stepping 0c
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfb3f0, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router VIA [1106/0586] at 00:07.0
Activating ISA DMA hang workarounds.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039 Starting kswapd v1.8
parport0: PC-style at 0x378 [PCSPP(,...)]
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
lp0: using parport0 (polling).
block: queued sectors max/low 212421kB/81349kB, 640 slots per queue
loop: enabling 8 loop devices
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c586b (rev 47) IDE UDMA33 controller on pci00:07.1

    ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
Quoted 16 lines

hda: Maxtor 91080D5, ATA DISK drive
hdc: ASUS CD-S400/A, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 21095424 sectors (10801 MB) w/512KiB Cache, CHS=1313/255/63, UDMA(33)
hdc: ATAPI 40X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
hdd: 98304kB, 196608 blocks, 512 sector size, , DMA
hdd: 98304kB, 96/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm Partition check:
hda: hda1 hda2 hda3 hda4
hdd: hdd4
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ >

SERIAL_PCI

Quoted 140 lines

enabled
ttyS01 at 0x02f8 (irq = 3) is a 16550A
PPP generic driver version 2.4.1
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 263M
agpgart: Detected Via MVP3 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
fatfs: bogus cluster size
reiserfs: checking transaction log (device 03:04) ...
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC } Using tea hash to sort names
reiserfs: using 3.5.x disk format
ReiserFS version 3.6.25
VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 176k freed
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide0: reset: success
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide0: reset: success
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide0: reset: success
Adding Swap: 104416k swap-space (priority -1)
VFS: Disk change detected on device ide1(22,68)
hdd: hdd4
VFS: Disk change detected on device ide1(22,68)
hdd: hdd4

/proc/ide/via:
----------VIA BusMastering IDE Configuration----------------

Driver Version:                     3.20
South Bridge:                       VIA vt82c586b
Revision:                           ISA 0x47 IDE 0x6
BM-DMA base:                        0xe000
PCI clock:                          33MHz
Master Read  Cycle IRDY:            1ws
Master Write Cycle IRDY:            1ws
BM IDE Status Register Read Retry:  yes
Max DRDY Pulse Width:               No limit
-----------------------Primary IDE-------Secondary IDE------
Read DMA FIFO flush:          yes                 yes
End Sector FIFO flush:         no                  no
Prefetch Buffer:              yes                 yes
Post Write Buffer:            yes                  no
Enabled:                      yes                 yes
Simplex only:                  no                  no
Cable Type:                   40w                 40w
-------------------drive0----drive1----drive2----drive3-----
Transfer Mode:        DMA       DMA      UDMA       DMA
Address Setup:       30ns     120ns      30ns      60ns
Cmd Active:          90ns      90ns      90ns      90ns
Cmd Recovery:        30ns      30ns      90ns      90ns
Data Active:         90ns     330ns      90ns      90ns
Data Recovery:       30ns     270ns      30ns      90ns
Cycle Time:         120ns     600ns      60ns     180ns
Transfer Rate:   16.5MB/s   3.3MB/s  33.0MB/s  11.0MB/s

my normal /proc/ide/via (without ZIP):
----------VIA BusMastering IDE Configuration---------------- Driver Version:                     3.20
South Bridge:                       VIA vt82c586b
Revision:                           ISA 0x47 IDE 0x6 BM-DMA base:                        0xe000
PCI clock:                          33MHz
Master Read  Cycle IRDY:            1ws
Master Write Cycle IRDY:            1ws
BM IDE Status Register Read Retry:  yes
Max DRDY Pulse Width:               No limit -----------------------Primary IDE-------Secondary IDE------ Read DMA FIFO flush:          yes                 yes End Sector FIFO flush:         no                  no Prefetch Buffer:              yes                 yes Post Write Buffer:            yes                  no
Enabled:                      yes                 yes Simplex only:                  no                  no Cable Type:                   40w                 40w -------------------drive0----drive1----drive2----drive3----- Transfer Mode:       UDMA       DMA      UDMA       DMA Address Setup:       30ns     120ns      30ns     120ns Cmd Active:          90ns      90ns      90ns      90ns Cmd Recovery:        30ns      30ns      30ns      30ns Data Active:         90ns     330ns      90ns     330ns Data Recovery:       30ns     270ns      30ns     270ns Cycle Time:          60ns     600ns      60ns     600ns Transfer Rate:   33.0MB/s   3.3MB/s  33.0MB/s   3.3MB/s

BIOS' uDMA settings for Primary Master and Slave are "Auto", for Secondary Master and Slave are "Disabled", but Linux detects DMA for all devices (see dmesg).

What could I do? Try the 2.4.2-ac12 kernel?

cu Konrad

Signature · 1 line
Konrad Stopsack - [email protected]
#1 lore raw
Quoted 14 lines · Konrad Stopsack

Hello guys,

I hope you've read my posting "DMA problem with ZIP drive and VIA VT82C598MVP / VT82C586B chip" (why does anybody answer?).
I now tried the 2.4.2-ac12 kernel including the latest VIA 82c586b driver (version 3.21), but the effects were almost the same:
- just when the kernel tried to access to the hard disk during boot, DMA errors were occured
- "hdparm /dev/hda" displayed 9 MB per second (and not 11 MB like without ZIP) - /proc/ide/via reported 16 MB transfer rate (and not 33MB like without ZIP drive)
- Kernel 2.4.2-ac12 reports a "ide-floppy: hdd: I/O error, pc = 5a, key = 5, asc = 24, ascq = 0" error, 2.4.2 doesn't

Quoted 6 lines

My IDE configuration is:
/dev/hda: Hard disk => Primary IDE controller
/dev/hdc CD-ROM => Secondary IDE controller
/dev/hdd: ZIP => Secondary IDE controller

Could you please tell me whether it's a bug or a feature?

OK. The ZIP drive can not handle uDMA, so it's normal for the secondary controller to drop back. In my opinion, the primary controller should stay at uDMA speed, but it is PC hardware so it is perfectly possible there is something cheap that locks them together. I will bring up ac-12 and check the error message...

Quoted 8 lines

I'm really waiting for your answer - else I might get crazy with this problem

:-((

I attached both dmesg and /proc/ide/via, and my old posting.

cu Konrad

Signature · 3 lines
Paul Bristow
http://paulbristow.net/linux/idefloppy.html
Linux ide-floppy maintainer
#2 lore raw
In reply to Konrad Stopsack
Quoted 20 lines · Paul Bristow
Quoted 19 lines · Konrad Stopsack

Hello guys,

I hope you've read my posting "DMA problem with ZIP drive and VIA VT82C598MVP / VT82C586B chip" (why does anybody answer?).
I now tried the 2.4.2-ac12 kernel including the latest VIA 82c586b driver (version 3.21), but the effects were almost the same:
- just when the kernel tried to access to the hard disk during boot, DMA errors were occured
- "hdparm /dev/hda" displayed 9 MB per second (and not 11 MB like without ZIP) - /proc/ide/via reported 16 MB transfer rate (and not 33MB like without ZIP drive)
- Kernel 2.4.2-ac12 reports a "ide-floppy: hdd: I/O error, pc = 5a, key = 5, asc = 24, ascq = 0" error, 2.4.2 doesn't

My IDE configuration is:
/dev/hda: Hard disk => Primary IDE controller
/dev/hdc CD-ROM => Secondary IDE controller
/dev/hdd: ZIP => Secondary IDE controller

Quoted 7 lines
Quoted 1 line

Could you please tell me whether it's a bug or a feature?

OK. The ZIP drive can not handle uDMA, so it's normal for the secondary controller to drop back. In my opinion, the primary controller should stay at uDMA speed, but it is PC hardware so it is perfectly possible there is something cheap that locks them together. I will bring up ac-12 and check the error message...

Actually I'm beginning to suspect the PSU here ... does removing the CD-ROM (leaving just the HDD and the ZIP in) help? Does the ZIP cause errors even when connected just to the power cable (and not the IDE cable)?

Signature · 2 lines
Vojtech Pavlik
SuSE Labs
#3 lore raw
Quoted 10 lines · Vojtech Pavlik
Quoted 6 lines · Paul Bristow
Quoted 5 lines · Konrad Stopsack

Hello guys,

I hope you've read my posting "DMA problem with ZIP drive and VIA VT82C598MVP / VT82C586B chip" (why does anybody answer?). I now tried the 2.4.2-ac12 kernel including the latest VIA 82c586b

driver

Quoted 2 lines
Quoted 2 lines

(version 3.21), but the effects were almost the same:
- just when the kernel tried to access to the hard disk during boot,

Quoted 18 lines

DMA

Quoted 2 lines
Quoted 2 lines

errors were occured
- "hdparm /dev/hda" displayed 9 MB per second (and not 11 MB like

without

Quoted 3 lines
Quoted 3 lines

ZIP) - /proc/ide/via reported 16 MB transfer rate (and not 33MB like without ZIP drive)
- Kernel 2.4.2-ac12 reports a "ide-floppy: hdd: I/O error, pc = 5a,

key =

Quoted 10 lines
Quoted 8 lines

5, asc = 24, ascq = 0" error, 2.4.2 doesn't

My IDE configuration is:
/dev/hda: Hard disk => Primary IDE controller
/dev/hdc CD-ROM => Secondary IDE controller
/dev/hdd: ZIP => Secondary IDE controller

Could you please tell me whether it's a bug or a feature?

OK. The ZIP drive can not handle uDMA, so it's normal for the

secondary

Quoted 5 lines
Quoted 2 lines

controller to drop back. In my opinion, the primary controller should

stay

Quoted 1 line

at uDMA speed, but it is PC hardware so it is perfectly possible there

is

Quoted 9 lines
Quoted 1 line

something cheap that locks them together. I will bring up ac-12 and

check

Quoted 1 line

the error message...

Actually I'm beginning to suspect the PSU here ... does removing the CD-ROM (leaving just the HDD and the ZIP in) help? Does the ZIP cause errors even when connected just to the power cable (and not the IDE cable)?

Do you mean the Power Supply Unit? Or the Program Storage Unit? ;-)

To answer to your questions:
- I haven't tried to remove the CD-ROM because both devices shall work
together
- the ZIP doesn't cause problems when just the power cable is connected

Although my PC has only got an old Baby AT 200W power supply I don't think that's the point.

cu Konrad

Signature · 3 lines
Konrad Stopsack - [email protected]

Sent through GMX FreeMail - http://www.gmx.net
#4 lore raw
In reply to Vojtech Pavlik
Quoted 1 line · On Thu, Mar 08, 2001 at 09:01:15AM +0100, [email protected] wrote:

Do you mean the Power Supply Unit? Or the Program Storage Unit? ;-)

Power Supply Unit, yes.

Quoted 7 lines

To answer to your questions:
- I haven't tried to remove the CD-ROM because both devices shall work
together
- the ZIP doesn't cause problems when just the power cable is connected

Although my PC has only got an old Baby AT 200W power supply I don't think that's the point.

I don't see any other way how the ZIP could have impact on the IDE HDD on a different IDE interface.

If you wonder why /proc/ide/via reports slower DMA rates for the HDD when the ZIP is connected is because the auto slowdown code kicks in and lowers the transfer rate when too many CRC errors happen.

Signature · 2 lines
Vojtech Pavlik
SuSE Labs
#5 lore raw
Quoted 8 lines · Vojtech Pavlik
Quoted 1 line · Konrad Stopsack

Do you mean the Power Supply Unit? Or the Program Storage Unit? ;-)

Power Supply Unit, yes.

Quoted 2 lines

To answer to your questions:
- I haven't tried to remove the CD-ROM because both devices shall

work

Quoted 2 lines
Quoted 2 lines

together
- the ZIP doesn't cause problems when just the power cable is

connected

Quoted 7 lines
Quoted 2 lines

Although my PC has only got an old Baby AT 200W power supply I don't

think

Quoted 1 line

that's the point.

I don't see any other way how the ZIP could have impact on the IDE HDD on a different IDE interface.

The 82c586b can be a chip with locked-together IDE controllers, can't it?

Quoted 4 lines

If you wonder why /proc/ide/via reports slower DMA rates for the HDD when the ZIP is connected is because the auto slowdown code kicks in and lowers the transfer rate when too many CRC errors happen.

Well, and what should I do now? I really need the ZIP drive. Try without CD-ROM? Buy new ATX case with 300W power supply? And new motherboard? And new processor? And ... and ... and?
Isn't there a chance to unlock the IDE channels (if they are locked)? Remember, I've heard about a Windows patch to do this.

Paul, what did you find out?

cu Konrad

Signature · 3 lines
Konrad Stopsack - [email protected]

Sent through GMX FreeMail - http://www.gmx.net