Skip to contentSkip to conversation

How can I save zImage & fsimage.tar into Flash memory then boot

U-Boot-Users Jacob Chan 3 participants 5 messages Jul 1, 2003 1 message not in the archive

lore
Share & tools
lore

Jacob Chan

author
#1 lore raw
In reply to a message not in the archive

I am using diff-2.4.18-rmk7-pxa3 kernel.
Could you tell me the complete command about mkimage that you type I am type mkimage -A arm -O linux -T kernel -C none -a 0xa0200000 -e 0xc0004000 -n zImage -d zImage bootm ---------------------------------------msg begin-------------------------------------------------------------

Image Name:   zImage
Created:      Wed Jul  2 01:44:06 2003
Image Type:   ARM Linux Kernel Image (uncompressed)
Data Size:    656752 Bytes = 641.36 kB = 0.63 MB
Load Address: 0xa0200000
Entry Point:  0xc0004000

-----------------------------------------msg end------------------------------------------------------------- Is that correct??
Then I using bootm 0xa0200000 atfer I loadb
The system is also crash... ----------------------------------------msg begin------------------------------------------------------------

$ loadb 0xa0200000
## Ready for binary (kermit) download to 0xA0200000 at 115200 bps...
## Total Size      = 0x000a05b0 = 656816 Bytes
## Start Addr      = 0xA0200000
$ bootm 0xa0200000
## Booting image at a0200000 ...
   Image Name:   zImage
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    656752 Bytes = 641.4 kB
   Load Address: a0200000
   Entry Point:  c0004000
   Verifying Checksum ... OK
   XIP Kernel Image ... OK

Starting kernel ...

prefetch abort

pc : [<c0004004>]    lr : [<a30128b4>]

sp : a2f9fdf0 ip : 00000001 fp : 00000002
r10: a301c254 r9 : 0bb1c300 r8 : a2f9ffc4
r7 : a301c254 r6 : a0200040 r5 : 00000000 r4 : a0200040 r3 : c0004000 r2 : 00000001 r1 : 00000059 r0 : 00000000
Flags: nZCv IRQs off FIQs off Mode SVC_32 Resetting CPU ...

reseting ...
---------------------------------msg end----------------------------------------------
By the way, Could you tell me what kind of target board that you used? Your reply and support will be highly appreciated.

Thank you for your time and attention

Jacob Chan
Jacob_chan at so-net.net.tw

-----Original Message-----
From: Zhao Hongda [mailto:zhaohd at vis.cs.tsinghua.edu.cn]
Sent: Tuesday, July 01, 2003 5:38 PM
To: Jacob Chan
Subject: Re: [U-Boot-Users] How can I save zImage & fsimage.tar into Flash memory then boot

the U-boot have mkimage in tools/ directory,
I'm using 2.4.19-rmk7-pxa2 kernel, it can work fine with armboot, but always crash in u-boot, could you tell me which rmk and pxa patch you
applied to 2.4.18 kernel?
if you can have a workable u-boot Image, please let me know. Best regards.
Hongda Zhao
----- Original Message -----
From: "Jacob Chan" <[email protected]>
To: "'Zhao Hongda'" <[email protected]>
Sent: Tuesday, July 01, 2003 5:30 PM
Subject: RE: [U-Boot-Users] How can I save zImage & fsimage.tar into Flash
memory then boot

Quoted 18 lines

I am using Linux Kernel 2.4.18 with xscale pxa patch By the way, Could you tell me where to download mkimage tool Your reply and support will be highly appreciated.

Thank you for your time and attention

Jacob Chan
Jacob_chan at so-net.net.tw

-----Original Message-----
From: u-boot-users-admin at lists.sourceforge.net [mailto:u-boot-users-admin at lists.sourceforge.net] On Behalf Of Zhao Hongda
Sent: Tuesday, July 01, 2003 5:00 PM
To: u-boot-users at lists.sourceforge.net
Subject: Re: [U-Boot-Users] How can I save zImage & fsimage.tar into Flash memory then boot

Quoted 20 lines

Could you tell me which kernel version is used?
I'm try to use mkimage to create a flash-image that can be used by bootm,
but until now I'm failed.
Hongda Zhao
----- Original Message -----
From: "Jacob Chan" <[email protected]>
To: "u-boot" <[email protected]>
Sent: Tuesday, July 01, 2003 4:26 PM
Subject: [U-Boot-Users] How can I save zImage & fsimage.tar into Flash memory then boot

Quoted 7 lines

Dear all,
I am using the Intel DBPXA255 Lubbock board.
After I download the u-boot.bin via JTAG that using BDI2000. It can boot but the Ethernet device(SMSC LAN91C96) is not work. So I using serial download(Kermit mode) zImage to the address 0xa0200000. loadb 0xa0200000 <-- using HyperTerminal Kermit mode to download After that I can using go 0xa0200000 to boot linux kernel, but how

can

Quoted 23 lines

I

Quoted 6 lines

save it to Flash?
I try cp 0xa0200000 0x00080000 0x000a0578
After that I reboot the target board and how can I boot the linux kernel?
I use bootm 0x00080000, but it's not work.
Finally, I wan to save u-boot.bin, zImage and filesystem.tar into

Flash

Quoted 15 lines

then boot.
What should I need to do? Your reply and support will be highly appreciated.

Thank you for your time and attention

Jacob Chan
Jacob_chan at so-net.net.tw

-------------------------------------------------------
This SF.Net email sponsored by: Free pre-built ASP.NET sites

including

Quoted 4 lines
Quoted 3 lines

Data Reports, E-commerce, Portals, and Forums are available now. Download today and enter to win an XBOX or Visual Studio .NET.

http://aspnet.click-url.com/go/psa00100006ave/direct;at.asp_061203_01/01

Quoted 9 lines
Quoted 5 lines

_______________________________________________
U-Boot-Users mailing list
U-Boot-Users at lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/u-boot-users

Quoted 5 lines

-------------------------------------------------------
This SF.Net email sponsored by: Free pre-built ASP.NET sites including Data Reports, E-commerce, Portals, and Forums are available now. Download today and enter to win an XBOX or Visual Studio .NET.

http://aspnet.click-url.com/go/psa00100006ave/direct;at.asp_061203_01/01

Quoted 6 lines

_______________________________________________
U-Boot-Users mailing list
U-Boot-Users at lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/u-boot-users

#2 lore raw
Quoted 4 lines · Jacob Chan

I am using diff-2.4.18-rmk7-pxa3 kernel.
Could you tell me the complete command about mkimage that you type I am type mkimage -A arm -O linux -T kernel -C none -a 0xa0200000 -e 0xc0004000 -n zImage -d zImage bootm

I think this has been discussed on this mailing list before.

Here is the procedure I use for creating a bootable image for PXA.

arm-linux-objcopy -S -O binary vmlinux linux
gzip -vf9 linux

mkimage -n kernel_name -A arm -O linux -T kernel -C gzip -a a0008000 \
              -e a0008000 -d linux.gz linuxgz.image

I then copy this in to flash at 0x40000 and boot with "bootm 40000". Since I use a mtd device as the rootfs there is only a single arg to the bootm command.

HTH, Kyle.

#3 lore raw

After do such steps, I try to "bootm 0x40000", but the kernel hangs:

    ## Booting image at 00040000 ...
        Image name:    2.4.18    kernel
        Image Type:    ARM Linux kernel Image (gzip compressed)
        Data Size:        714025 Bytes =697.3kB
        Load Address:   a0008000
        Entry Point:        a0008000
        Verifying Checksum ... OK
        Uncompressing Kernel Image ... OK
    Starting kernel...
    (hangs)

why? should I change some envs?
Hongda Zhao
----- Original Message -----
From: "Kyle Harris" <[email protected]>
To: "Jacob Chan" <[email protected]>; "'Zhao Hongda'" <[email protected]>
Cc: "u-boot" <[email protected]>
Sent: Tuesday, July 01, 2003 8:20 PM
Subject: Re: [U-Boot-Users] How can I save zImage & fsimage.tar into Flash memory then boot

Quoted 10 lines · Jacob Chan
Quoted 5 lines

I am using diff-2.4.18-rmk7-pxa3 kernel.
Could you tell me the complete command about mkimage that you type I am type mkimage -A arm -O linux -T kernel -C none -a 0xa0200000 -e 0xc0004000 -n zImage -d zImage bootm

I think this has been discussed on this mailing list before.

Quoted 8 lines

Here is the procedure I use for creating a bootable image for PXA.

arm-linux-objcopy -S -O binary vmlinux linux
gzip -vf9 linux

mkimage -n kernel_name -A arm -O linux -T kernel -C gzip -a a0008000 \
              -e a0008000 -d linux.gz linuxgz.image

I then copy this in to flash at 0x40000 and boot with "bootm 40000". Since

I

Quoted 5 lines

use a mtd device as the rootfs there is only a single arg to the bootm command.

HTH, Kyle.

#4 lore raw
Quoted 11 lines · Zhao Hongda

After do such steps, I try to "bootm 0x40000", but the kernel hangs:

    ## Booting image at 00040000 ...
        Image name:    2.4.18    kernel
        Image Type:    ARM Linux kernel Image (gzip compressed)
        Data Size:        714025 Bytes =697.3kB
        Load Address:   a0008000
        Entry Point:        a0008000
        Verifying Checksum ... OK
        Uncompressing Kernel Image ... OK
    Starting kernel...
    (hangs)

What are your bootargs? Make sure the console is configured correctly.

console=ttyS0,115200

#5 lore raw

my kernel config is (arch/arm/def-configs/lubbock):
...
CONFIG_CMDLINE="root=/dev/nfs ip=bootp console=ttyS0,115200"
...
my u-boot env config is:
...
bootargs=root=/dev/nfs ip=bootp console=ttyS0,115200
...
stdin=serial
stdout=serial
stderr=serial
...

is it right?
Hongda zhao
----- Original Message -----
From: "Kyle Harris" <[email protected]>
To: "Zhao Hongda" <[email protected]>; <[email protected]>
Sent: Tuesday, July 01, 2003 9:14 PM
Subject: Re: [U-Boot-Users] How can I save zImage & fsimage.tar into Flash memory then boot

Quoted 30 lines · Zhao Hongda
Quoted 12 lines

After do such steps, I try to "bootm 0x40000", but the kernel hangs:

    ## Booting image at 00040000 ...
        Image name:    2.4.18    kernel
        Image Type:    ARM Linux kernel Image (gzip compressed)
        Data Size:        714025 Bytes =697.3kB
        Load Address:   a0008000
        Entry Point:        a0008000
        Verifying Checksum ... OK
        Uncompressing Kernel Image ... OK
    Starting kernel...
    (hangs)

What are your bootargs? Make sure the console is configured correctly.

console=ttyS0,115200

-------------------------------------------------------
This SF.Net email sponsored by: Free pre-built ASP.NET sites including Data Reports, E-commerce, Portals, and Forums are available now. Download today and enter to win an XBOX or Visual Studio .NET.
http://aspnet.click-url.com/go/psa00100006ave/direct;at.asp_061203_01/01
_______________________________________________
U-Boot-Users mailing list
U-Boot-Users at lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/u-boot-users