Kernel booting on serial console ... crawling
Quoted 11 lines
I tried to boot my kernel using the serial console, using the console=ttyS0,115200 (it does the same thing with 9600) ... it work great until :
Freeing unused kernel memory: 36k freed serial console detected. Disabling virtual terminals. console=/dev/ttyS0
At this point the output of the serial line slow down dramaticly ... almost to a halt ... I get 1 line every 30 seconds !!!
Is this an AMD Elan's built-in serial port, perchance ?
Rob
----------------------------------------------------------------
Robert Kaiser email: [email protected]
SYSGO RTS GmbH
Am Pfaffenstein 14 phone: (49) 6136 9948-762
D-55270 Klein-Winternheim / Germany fax: (49) 6136 9948-10
Hi Rob,
Quoted 1 line · Robert Kaiser
Is this an AMD Elan's built-in serial port, perchance ?
I got a patch for the Elan's serial port from Jason Sodergren some days ago, but it's not clear to me what exactly the problem is with this port. I'm using the serial console on a DIL/Net-PC without any problems so far. Perhaps it might be a good idea to join forces and try to get a patch for the Elan series into the main kernel?
However, my current affords can be found on
http://www.schwebel.de/software/dnp/index_en.html
This currently implements a new CPU configuration parameter and a fix for the clock on the Elan CPUs.
Robert
Signature · 6 lines
+--------------------------------------------------------+ | Dipl.-Ing. Robert Schwebel | | Pengutronix - Linux Solutions for Science and Industry | | Braunschweiger Straße 79, 31134 Hildesheim, Germany | | Phone: +49-5121-28619-0 Fax: +49-5121-28619-4 | +--------------------------------------------------------+
Hi Robert,
Am Freitag, 9. November 2001 13:27 schrieben Sie:
Quoted 9 lines · Robert Kaiser
Quoted 1 line
Is this an AMD Elan's built-in serial port, perchance ?
I got a patch for the Elan's serial port from Jason Sodergren some days ago, but it's not clear to me what exactly the problem is with this port. I'm using the serial console on a DIL/Net-PC without any problems so far. Perhaps it might be a good idea to join forces and try to get a patch for the Elan series into the main kernel?
Quoted 6 lines
However, my current affords can be found on
http://www.schwebel.de/software/dnp/index_en.html
This currently implements a new CPU configuration parameter and a fix for the clock on the Elan CPUs.
This is interesting, I was not aware of the different clock frequency issue.
Anyway, the patch I am using to fix the crawling console output symptom on the Elan is entirely different (see attachment). It was originally posted by Anders Larsen <[email protected]> and we have been using it with good success in our embedded Linux product for quite a while now. The comments in the source describe the problem. Interestingly, even the latest AMD Elan product (SC520) seems to have this problem too.
Rob
----------------------------------------------------------------
Robert Kaiser email: [email protected]
SYSGO RTS GmbH
Am Pfaffenstein 14 phone: (49) 6136 9948-762
D-55270 Klein-Winternheim / Germany fax: (49) 6136 9948-10
Index: sysgo/elinos/linux/drivers/char/serial.c
diff -c sysgo/elinos/linux/drivers/char/serial.c:1.2 sysgo/elinos/linux/drivers/char/serial.c:1.3
*** sysgo/elinos/linux/drivers/char/serial.c:1.2 Wed May 17 14:07:00 2000
--- sysgo/elinos/linux/drivers/char/serial.c Wed Jun 7 15:19:53 2000
***************
*** 607,612 ****
--- 607,613 ----
int status;
struct async_struct * info;
int pass_counter = 0;
+ int iir;
struct async_struct *end_mark = 0;
#ifdef CONFIG_SERIAL_MULTIPORT
int first_multi = 0;
***************
*** 627,635 ****
first_multi = inb(multi->port_monitor);
#endif
do {
if (!info->tty ||
! (serial_in(info, UART_IIR) & UART_IIR_NO_INT)) {
if (!end_mark)
end_mark = info;
goto next;
--- 628,637 ----
first_multi = inb(multi->port_monitor);
#endif
+ iir = serial_in(info, UART_IIR);
do {
if (!info->tty ||
! ((iir = serial_in(info, UART_IIR)) & UART_IIR_NO_INT)) {
if (!end_mark)
end_mark = info;
goto next;
***************
*** 645,650 ****
--- 647,663 ----
if (status & UART_LSR_DR)
receive_chars(info, &status);
check_modem_status(info);
+ #ifdef CONFIG_AMD_ELAN
+ /*
+ ** There is a bug (misfeature?) in the UART on the AMD Elan
+ ** SC4x0 and SC520 embedded processor series; the THRE bit of
+ ** the line status register seems to be delayed one bit
+ ** clock after the interrupt is generated, so kludge this
+ ** if the IIR indicates a Transmit Holding Register Interrupt
+ */
+ if ((iir & UART_IIR_ID) == UART_IIR_THRI)
+ status |= UART_LSR_THRE;
+ #endif
if (status & UART_LSR_THRE)
transmit_chars(info, 0);
***************
*** 679,685 ****
*/
static void rs_interrupt_single(int irq, void *dev_id, struct pt_regs * regs) {
! int status;
int pass_counter = 0;
struct async_struct * info;
#ifdef CONFIG_SERIAL_MULTIPORT
--- 692,698 ----
*/
static void rs_interrupt_single(int irq, void *dev_id, struct pt_regs * regs) {
! int status, iir;
int pass_counter = 0;
struct async_struct * info;
#ifdef CONFIG_SERIAL_MULTIPORT
***************
*** 701,706 ****
--- 714,720 ----
first_multi = inb(multi->port_monitor);
#endif
+ iir = serial_in(info, UART_IIR);
do {
status = serial_inp(info, UART_LSR);
#ifdef SERIAL_DEBUG_INTR
***************
*** 709,714 ****
--- 723,739 ----
if (status & UART_LSR_DR)
receive_chars(info, &status);
check_modem_status(info);
+ #ifdef CONFIG_AMD_ELAN
+ /*
+ ** There is a bug (misfeature?) in the UART on the AMD Elan
+ ** SC4x0 and SC520 embedded processor series; the THRE bit of
+ ** the line status register seems to be delayed one bit
+ ** clock after the interrupt is generated, so kludge this
+ ** if the IIR indicates a Transmit Holding Register Interrupt
+ */
+ if ((iir & UART_IIR_ID) == UART_IIR_THRI)
+ status |= UART_LSR_THRE;
+ #endif
if (status & UART_LSR_THRE)
transmit_chars(info, 0);
if (pass_counter++ > RS_ISR_PASS_LIMIT) {
***************
*** 717,723 ****
#endif
break;
}
! } while (!(serial_in(info, UART_IIR) & UART_IIR_NO_INT));
info->last_active = jiffies;
#ifdef CONFIG_SERIAL_MULTIPORT
if (multi->port_monitor)
--- 742,748 ----
#endif
break;
}
! } while (!((iir = serial_in(info, UART_IIR)) & UART_IIR_NO_INT));
info->last_active = jiffies;
#ifdef CONFIG_SERIAL_MULTIPORT
if (multi->port_monitor)